The i30s current clamp is based on hall effect technology for use in measurement of both DC and AC current. The i30s may be used in conjunction with oscilloscopes and other suitable recording instruments for accurate non-intrusive current measurement. Specified current range: 30 mA to 30A DC, 30 mA to 20 A AC rms. Usable current range: 5 mA to 30 A DC, 30 mA to 20 A AC rms. Crest factor: 1.4". Output sensitivity: 100 mV/A. Accuracy (at +25 degree C): +/-1 percent of reading +/-2 mA. Resolution: +/-1 mA. Load impedance: greater than 100 kilo ohm. Conductor position sensitivity: +/-1 percent relative to center reading. Frequency range: DC to 100 kHz (- 0.5 dB). Phase shift below 1 kHz: less than 2 degrees. Temperature coefficient: +/-0.01 percent of reading/degree C. Power supply: 9 V Alkaline, MN1604/PP3, 30 hours, low battery indicator. Working voltage (see Safety Standards section): 300 V AC rms or DC. Maximum conductor size: 19mm diameter. Output connection: Safety BNC connector, supplied with safety 4mm adapter. Output zero: Manual adjust via thumbwheel. Cable length: 2 meters. Operating temperature range: 0 to +50 degree C. Storage temperature range (with battery removed): -20 to +85 degree C. Operating humidity: 15 to 85 percent (non-condensing). Safety standards: BS EN 61010-1: 2001, BS EN 61010-2-032: 2002, BS EN 61010-031: 2002, 300 Vrms, Category III, Pollution Degree 2, Use of the probe on uninsulated conductors is limited to 300 V AC RMS or dc and frequencies below 1 kHz. EMC Standards: EN 61326: 1998 +A1, A2, and A3. Measures 71mm width by 183mm height by 25mm depth.
Current clamp is based on hall effect technology
Use in measurement of both DC and AC current
it may be used in conjunction with oscilloscopes and other suitable recording instruments for accurate non-intrusive current measurement
1.4" Crest factor
100 mV/A output sensitivity
Product Information Specifications for Fluke I30S AC/DC Current Clamp, 300V AC/DC Voltage, 30A DC, 20A AC rms Current Below:
Mid-West Instrument Backflow prevention assembly test kit includes 5 valve. The 835 is in the list of acceptable gages from both FCCC and HR-USC and CA-NV AWWA. Backflow test kits provide the capability for testing all brands of reduced pressure prin...
Loop Calibrator is a high performance solution for calibration, repair and maintenance of current loops. The new "Quick Click" knob making it extremely fast and easy to use. Large display and simple, quick-click interface for easy one-handed operatio...
General Wire P-XP-B Mini-Rooter XP Drain Cleaner with Power Cable Feed and 5/16-Inch x 75-Inch Cable, Small
Manufacturer: General Wire
Brand: General Wire
The Mini-Rooter XP gives you extra portability because 8" semi-pneumatic wheels let you keep the weight on the ground. An easy-grip handle folds down to save space and locks to use as an additional lifting handle. A roll bar protects the 1/3 hip moto...
The Fluke 1587 MDT advanced insulation and motor drive troubleshooting kit is designed for troubleshooting and preventive maintenance applications including three-phase motors, cables, switch gear, and in applications where testing is required withou...
Pouring (wide) end diameter = 1-5/16" (35 mm)
Insertion (narrow) end diameter = 3/16" (5 mm)
Easily transfer your essential oils into smaller dispensers
As with any product, please wash before use.
Pressure Switch, High, Switch Type SPST, Switch Action Open on Rise, Range (PSI) 150-700, Close (PSI) 150, Open (PSI) 200, Differential Pressure (PSI) 200 to 150, Auto Reset, Pressure Connection 1/4 In Female SAE, Capillary Length (In.) 18, Universal...