The Amprobe ACD-10 Plus digital clamp meter is an average-sensing, auto-ranging multimeter for measuring current, voltage, capacitance, resistance, and frequency in electrical testing applications. It has a transformer clamp that measures alternating current (AC) to 600 amp and frequency to 100 kilohertz (kHz), and it comes with detachable test leads that measure direct current (DC) voltage and AC voltage to 600 volts (V), capacitance to 3,000 microfarads, resistance to 40 megaohms, and frequency to 100 kHz. The clamp has two 0.4" (10 mm) thick jaws that are slimmer than standard clamp jaws for improved access to tight areas. The jaws can close around electrical conductors up to 1" (26 mm) in diameter to measure current without touching or interrupting the circuit. A relative zero mode stores a reading in memory to use as a zero point for subsequent readings, allowing for quick comparison of multiple readings. The maximum reading mode displays the highest reading in a session to track a sudden increase in measurements. An audible continuity sensor confirms that the circuit conducts electricity, and a diode test detects whether a circuit’s diodes are working properly. The hold function keeps the reading on the display, even after the meter is disconnected. The unit automatically turns off after 30 minutes of non-use to conserve battery life, and a low-battery indicator signals when the meter's batteries need to be replaced. A finger guard on the body of the meter helps protect fingers from shock.
This average-sensing, or average-responding, meter provides accurate readings when measuring linear loads, such as standard induction motors and incandescent lights, where the current or voltage has a sinusoidal waveform. It is an auto-ranging multimeter and automatically selects the correct operating range for the property being measured. The meter has a 4,000-count resolution, meaning that it can display up to 3,999 units (3-3/4 digits) before the operating range needs to be changed. It meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category III installations up to 600V, which covers items used with enclosed building circuit installations (service panel parts, branch circuits, and fixed installations that are connected directly to a building's AC power supply). The unit comes with a soft vinyl carrying case.
Specifications
Maximum alternating current (AC) input
600 amp
Maximum AC voltage input
600 volts (V)
Maximum direct current (DC) voltage input
600V
Maximum resistance detected
40 megaohms
Maximum capacitance detected
3,000 microfarads
Maximum frequency detected
100 kilohertz (kHz)
Power supply
3V IEC-CR2032 coin battery (one, installed)
Standards met and certifications
European Normal (EN); International Electrotechnical Commission (IEC) and EN safety standard 61010-1; European Conformity (CE); and Australia N10140 certified
Weight
4.9 oz./139 g
Meter dimensions
7.4 x 2.5 x 1.3 inches/190 x 63 x 32 mm (H x W x D)
H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Clamp meters (also called clamp-on meters) measure electrical current without cutting through wires or touching or interrupting the electrical circuit. Available in handheld or benchtop models, clamp meters diagnose problems in electrical equipment, wiring, and power supplies. The meter's current clamp has two jaws that fit around a conductor to take measurements. All clamp meters test for current. Some come with test leads and inputs for measuring voltage, capacitance, and resistance. They display information either in analog or digital form. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltages determine meter choice. Safety ratings are based on the International Electrotechnical Commission's (IEC) standards for low-voltage test equipment. IEC 61010 delineates four overvoltage installation categories. In general, a meter with a category IV rating will provide more protection against transient voltages than a meter with a lower category rating.
Amprobe manufactures electrical testing equipment for commercial, industrial, and home use. The company was founded in 1948 and is headquartered in Everett, WA.
What’s in the Box?
ACD-10 Plus average-sensing digital clamp multimeter
(1) Test lead set
(1) 3V coin battery (installed)
Soft vinyl carrying case
Instructions
Digital clamp meter measures alternating current (AC) to 600 amp, direct current (DC) voltage and AC voltage to 600 volts (V), capacitance to 3,000 microfarads, resistance to 40 megaohms, and frequency to 100 kilohertz
Average-sensing meter provides accurate readings when measuring linear loads, where the current or voltage has a sinusoidal waveform
Transformer clamp with 1" (26 mm) jaw opening has jaws that are slimmer than standard clamp jaws, for improved access to tight areas, and measures current without touching or interrupting the circuit
A relative zero mode stores a reading in memory to use as a zero point for subsequent readings
Meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category III installations up to 600V
Rubber over-molded case
Hold and maximum reading functions
Capacitance to 3000 uF
Meets EN61010-2-032, UL61010B-2-032, IEC61010-1 2nd Ed., EN61010-1 2nd Ed., UL61010-1 2nd Ed. CAT III-600 Volts ac & dc
Pollution degree : 2
Product Information Specifications for Amprobe ACD-10 PLUS 600A Clamp Multimeter Below:
The Fluke 59 Series Infrared Thermometer is designed to provide precise laser technology for more accurate and repeatable measurements. It has a large, easy-to-read backlit LCD display for easy viewing. It is small and lightweight design fits easily ...
Display 3-1/2 digits LCD, maximum reading 1999 Range 200/2000 mG,20/200μT Resolution 0.1/1 mG or 0.01/0.1 μT Frequency response 30Hz to 300Hz Sensor Single Axis Accuracy ± (2.5%+6dgt) at 50Hz/60Hz Over load LCD display "OL" Sample rate 2.5 t...
Model name:10mW visual fault locator Universally connector for test different ST,SC,FC interfaces Test for both single-mode and multi-mode cables with optional 2.5mm fiber optic(Standard) connectors to 1.25mm adapter(Optional) High effective power ci...
SainSonic WattsOut OP-600 Portable Optical Power Meter + 20mW Visual Fault Locator Fiber Optic Cable Tester Meter for CATV CCTV Telecommunications Engineering Maintenance Cabling System
SainSonic WattsOut OP-600 miniature handheld optical power meter is for installation, operation and maintenance of optical fiber network special design of a precise, durable, convenient portable test instrument. With clever appearance, can choose to ...
Reed ST-335 Clamp Meter with Temperature Measurement, 40 Megaohms Resistance, 600V AC/DC Voltage, 400A AC Current
Resistance to 40 megaohm. Temperature range to 2372 degree F (1300 degree C). Capacitance to 100 microF. EN 61010-1 CAT 600V. Complete with test leads, type K thermocouple wire probe, batteries and carrying case. Specifications: AC current range: 400...
Mastercool (62010) Gray/Yellow Refrigerant Recovery Tank - 30 lb. Capacity