LCR Meters

Manufacturer: Peak Electronic Design Ltd Brand: Peak Electronic Design Ltd Model: CRC01M

Gold coated Crocodile Clip set with 2mm sockets, designed for use with the LCR40/LCR45 Peak Atlas testers. A pair of very high quality croc clips designed for the new 2mm LCR plugs. The sockets are superb quality, gold plated and compatible with industry standard 2mm banana plugs. These fit easily and securely to the 2mm LCR plugs. Supplied with fitting and probe compensation instructions. (Please note that these crocs are not compatible with 0.63mm square pin socket connectors. Datasheet is available at alltronics.com.

Manufacturer: B&K Precision Corporation Brand: B&K Precision Model: TL885D

BK Precision TL885D 885 & 886 Shorting Bar

Manufacturer: SainSmart Brand: SainSmart Color: Blue

* One -button operation, automatic shutdown, only 20nA shutdown current * Automatically detect NPN, PNP bipolar transistors, N -channel and P -channel MOS FET, JFET, diodes, two diodes, thyristors small power unidirectional and bidirectional thyristor * Automatic identification components pin arrangement * Measuring bipolar transistor current amplification factor and base - emitter threshold voltage. * Via the base - emitter threshold voltage and high current amplification factor to identify Darlington transistors * Can detect bipolar transistors and MOS transistors protection diodes. * Measuring the gate MOS FET threshold voltage and the gate capacitance. * Can simultaneously measure two resistors and resistor symbol is displayed. Displayed on the right with a decimal value of 4 . Resistance symbol on both sides shows the pin number. So you can measure the potentiometer. If the potentiometer wiper is not transferred to an extreme position , we can distinguish the middle and both ends of the pin. * Resistance measurement resolution is 0.1 ohms , 50M ohms can be measured * Can measure capacitance of 30pF-100mF , resolution 1pF. * 2uF more capacitors can simultaneously measure the equivalent series resistance ESR values. The two can be displayed with a decimal value , resolution 0.01 ohms. * Can be in the correct order and the diode symbol display two diodes , and gives the diode forward voltage. * LED is detected as a diode forward voltage higher . Combo of the LED is identified as two diodes. * Reverse breakdown voltage is less than 4.5V Zener diode can be identified. * Measure a single diode reverse capacitance. If the bipolar transistor connected to the base and collector or emitter of a pin , it can measure the collector or emitter junction reverse capacitance . * Can be obtained with a single measurement rectifier bridge connection.

Manufacturer: GW Instek Brand: GW Instek Model: LCR-13

4 Wire SMD/chip test fixture. SMD/chip components support. Suitable for SMD range: 0201 to 0805. For LCR-8000G and LCR-800 series LCR meter. Frequency: DC to 10 MHz. Maximum voltage: +/- 35V. BNC inputs are standard-spaced, and compatible with most four-wire LCR bridges.

Manufacturer: Gold-Line Brand: Gold-Line Model: ZM1P

A portable, battery operated meter useful to every sound contractor or installer, this unique instrument will make measurements on 25, 50, 70, or 100 volt line systems.

Manufacturer: B&K Precision Corporation Brand: B&K Precision Model: 886

High accuracy LCR/ESR meters were the first handheld meters of their type on the market, offering fast, reliable, and versatile testing at a low cost. With a wide range of test frequencies up to 100 kHz, these LCR meters can perform many different measurements - Z, L, C, DCR, ESR, D, Q, and diameter. Test conditions: 100 Hz, 120 Hz, 1 kHz, 10 kHz, 100 kHz (886), 1 Vrms, 0.25 Vrms, 0.05 Vrms. These instruments are designed for both component evaluation on the production line and fundamental impedance testing for benchtop applications. With a built-in direct test fixture, you can test lead components very easily. The optional 4-wire test clip can give a convenient connection to larger components and assemblies with the accuracy of 4-wire testing. Measurement parameters: Z, L, C, DCR, ESR, D, Q, and Diameter. 0.2 percent basic accuracy. Dual LCD display. SMD Surface Mount Tweezer Probe included. Very quick response, user friendly. Fully auto/manual selection. DC resistance measurement. Rechargeable battery / AC powered. Frequency accuracy: +/-0.1 percent. Level: 1Vrms, 0.25Vrms, 0.05Vrms, 1Vdc (for DCR). Level accuracy: +/-5 percent. Output impedance: 100 ohm, +/-5 percent. Operating temperature: 32 to 104 degree F (0 to 40 degree C). Storage temperature: -4 to 158 degree F (-20 to 70 degree C). Relative humidity: up to 85 percent. Battery type: Ni-MH or Alkaline (2 x AA size). Battery charge: Constant current 150mA approximately. Battery operating life: 2.5 hours typical. AC operation: 110V/220V AC, 60/50Hz with proper adapter. Low power warning: under 2.2V. Measures 6-57/64" length by 3-25/64" width by 1-57/64" height. 3 year warranty.

Manufacturer: Global Specialties Brand: Global Specialties Model: LCR-600

The LCR-600 is a high precision test instrument used for measuring the inductance (L), capacitance (C), and resistance (R) of an electrical component. The LCR-600 has an operational frequency range of 100 Hz to 100 kHz and basic measurement accuracy of 0.3%. There is a dual LCD display, measurement voltage fixed at 0.6 V, auto-detect function, and open-circuit /short-circuit compensation. Use the meter to check ESR values of capacitors and inductors, sort and select components, identify unknown components, and general LCR values.

Manufacturer: DER EE ELECTRICAL INSTRUMENT Brand: DER EE ELECTRICAL INSTRUMENT

Service parts For DE-5000

Manufacturer: DER EE ELECTRICAL INSTRUMENT Brand: DER EE ELECTRICAL INSTRUMENT Model: DE-5000

1. 100 / 120 / 1k / 10k / 100k Hz test frequency 2. Dual 19999/1999 display 3. Backlight 4. Ls / Lp / Cs / Cp / Rs / Rp / dissipation factor (D) / quality factor (Q) /phase angle/ ESR LCR auto selection 5. Auto Ranging mode 6. Auto Serial / Parallel mode 7. Components sorting function *Selectable tolerance ±0.25%, ±0.5%, ±1%, ±2%, ±5%, ±10%, ±20%, -20% +80% 8. Low battery indication

Manufacturer: GW Instek Brand: GW Instek Model: LCR-12

4 Wire test lead with kelvin clip. Odd-shaped components support. Suitable for low R or high C. For LCR-8000G and LCR-800 series LCR meter. Frequency: DC to 10 MHz. Maximum voltage: +/- 35V.