Current Testers - Page 121

Manufacturer: VDO Brand: VDO Model: A2C53210973-S

VDO A2C53210973-S Ammeter - +/- 100 Amps - Electronic - Viewline Onyx - Bezel not included

Manufacturer: Pomona Electronics Brand: Pomona Electronics

Test Leads BANANA PLUG/PIN TIP PLUG (RED)

Manufacturer: Fluke Corporation Brand: Fluke Model: BP190

Designed for use with the Fluke ScopeMeter 190 and 190C series, the Fluke BP190 rechargeable NiMH battery pack, this set of NiMH batteries has to be charged in the instrument. 7.2V Nominal voltage. 3,500 mAh capacity.

Manufacturer: Ruby Electronics Brand: Ruby Electronics Model: DT-3347 Color: Dark Gray & Yellow

This is a brand new CEM DT-3347 CE certified digital clamp-on AC/DC meter. DT-3347 Professional True RMS Clamp Meter provides accurate AC/DC Current and Voltage readings regardless of waveforms. This meter should be used in most industrial and commercial applications where non-linear loads distort the Current or Voltage waveform. This meter is CAT III 600V rated. It also measures capacitance, frequency, resistance and temperature. It comes with a heavy duty carrying case to protect your device when working in the field.

Manufacturer: Mueller Electric Brand: Mueller Electric

Test Clips Green Insul Alligato

Manufacturer: Kyoritsu Brand: Kyoritsu Model: 8128

Kyoritsu 8128 load current clamp sensor. In order to monitor energy saving and to control the electric facilities, it is essential and imperative to control the leak and load currents from mains and branch power lines up to the equipment. Clamp sensor is easy to carry and simple to install. High efficiency on the test terminal in power distribution facilities. Rated current 5Amp AC. 24mm conductor size. Output voltage: AC 50mV/5A[Max. 500mV/50A] (AC 10mV/A). Accuracy: +/- 0.5 percent rdg +/- 0.1mV (50/60Hz), +/- 1.0 percent rdg +/- 0.2mV (40Hz to 1kHz). Phase shift within +/- 2.0 degree. Output connector: Mini-DIN 6-pin. 0 to 50 degree c temperature range. Withstand voltage: 3540V AC for 5 seconds. Approximate 3m cable length. Approximate 20 ohm output impedance. Accessories includes: portable case, instruction manual, cable marker. Measures 100 mm length by 60 mm width by 26mm depth.

Manufacturer: Johnson / Emerson Connectivity Solutions Brand: Johnson / Emerson Connectivity Solutions

Test Plugs & Test Jacks .175 TURRET BLK

Manufacturer: Pomona Electronics Brand: Pomona Electronics

Test Plugs & Test Jacks BANANA PLUG VIOLET

Manufacturer: Amprobe Brand: Amprobe Model: ACDC-100 TRMS

The Amprobe digital clamp meter is auto- or manual-ranging multimeter for measuring current, voltage, capacitance, and resistance in electrical testing applications. It has a Hall effect clamp that measures alternating current (AC) to 800 amp and direct current (DC) to 1,000 amp. The meter comes with detachable test leads that measure DC voltage and AC voltage to 600 volts (V), capacitance to 3,000 microfarads, and resistance to 40 megaohms. The clamp has two jaws that can close around an electrical conductor up to 2" (50 mm) in diameter to measure current without touching or interrupting the circuit. The inrush reading displays measurement of entire motor inrush period at startup. A relative zero mode stores a reading in memory to use as a zero point for subsequent readings, allowing for quick comparison of multiple readings. The maximum reading mode displays the highest reading in a session to track a sudden increase in measurements. An audible continuity sensor confirms that the circuit conducts electricity, and a diode test detects whether a circuit’s diodes are working properly.

Manufacturer: Extech Instruments Brand: Extech Model: EX810 Color: Multicolor

Theses clamp-on multimeters priovide a built-in IR thermometer with laser pointer that makes troubleshooting heat sensitive areas simple. Features include data hold, Min/Max, autoranging with manual range button, auto power off, and an easy-to-read 4000 count backlit dual LCD display. Units ar CAT III, 600V rated. Model 26834-26 is CAT IV 600V rated. Clamp meter, multimeter and infrared thermometer all in one! Locate hot spots and overheating equipment with built-in IR thermometer Compact and powerful, the Extech EX810 1000-Amp AC Clamp Meter with Infrared Thermometer provides the versatility of multiple meters in one convenient device. The EX810 measures AC/DC voltage and current, resistance, diode, continuity, frequency, and capacitance. It also includes a built-in, non-contact infrared thermometer that allows you to detect invisible hot spots. A large, backlit display allows for easy reading, while the ergonomically designed housing offers comfortable, one-handed operation.1000A AC Clamp Meterwith IR ThermometerAt a Glance:Accurately makes a variety of electrical measurementsBuilt-in non-contact infrared thermometer for finding invisible hot spotsLarge LCD screen and backlit display for easy viewingErgonomic design and durable housing for one-handed operation and durabilityOne-year limited warranty on parts and laborEX810 clamp-on multimeter with built-in InfraRed Thermometer is ideal for industrial applications. View larger.Multipurpose Meter in One Convenient DeviceThe Extech EX810 offers multiple functions so service technicians can carry one meter into the field instead of several. This device measures AC current, AC/DC voltage, frequency, resistance, capacitance, diode, and continuity. Its wide-opening, 1-7/10- inch circular jaw fits around conductors up to 750 MCM, or two 500 MCM. The EX810 also features min/max, as well as data and peak hold of current surges during motor startup and other transience that "freezes" data in the display. Additionally, there is auto-ranging with manual override.Built-In, N...