Oscilloscope Accessories - Page 6

Manufacturer: Fluke Corporation Brand: Fluke Model: FLK-CNX-3000

The CNX 3000 Wireless Multimeter is the captain of the Fluke wireless team.With the CNX 3000 Wireless Multimeter you see live measurements from multiple modules simultaneously and remotely on a single screen. The CNX 3000 Wireless Multimeter displays the meter measurement, plus readings from up to 3 wireless modules and as far as 20 meters away. By seeing multiple readings at the same time, troubleshooters can see: Cause and effect, interactions between inputs/outputs, or other measurement points (simultaneously and remotely).If more than three readings are required from more modules, add an optional PC adapter to your laptop for real time viewing of up to 10 modules.The CNX wireless enabled module measures AC voltage, AC current, and temperature, which display on the CNX Wireless Multimeter. Choose a standard clamp or flexible clamp to measure AC current. Mix and match modules to suit your unique measurement needs. Read the primary measurement on the main display and up to three modules at any one time. Modules are available separately or as part of CNX kits.

Manufacturer: Fluke Corporation Brand: Fluke Model: I30S

The i30s current clamp is based on hall effect technology for use in measurement of both DC and AC current. The i30s may be used in conjunction with oscilloscopes and other suitable recording instruments for accurate non-intrusive current measurement. Specified current range: 30 mA to 30A DC, 30 mA to 20 A AC rms. Usable current range: 5 mA to 30 A DC, 30 mA to 20 A AC rms. Crest factor: 1.4". Output sensitivity: 100 mV/A. Accuracy (at +25 degree C): +/-1 percent of reading +/-2 mA. Resolution: +/-1 mA. Load impedance: greater than 100 kilo ohm. Conductor position sensitivity: +/-1 percent relative to center reading. Frequency range: DC to 100 kHz (- 0.5 dB). Phase shift below 1 kHz: less than 2 degrees. Temperature coefficient: +/-0.01 percent of reading/degree C. Power supply: 9 V Alkaline, MN1604/PP3, 30 hours, low battery indicator. Working voltage (see Safety Standards section): 300 V AC rms or DC. Maximum conductor size: 19mm diameter. Output connection: Safety BNC connector, supplied with safety 4mm adapter. Output zero: Manual adjust via thumbwheel. Cable length: 2 meters. Operating temperature range: 0 to +50 degree C. Storage temperature range (with battery removed): -20 to +85 degree C. Operating humidity: 15 to 85 percent (non-condensing). Safety standards: BS EN 61010-1: 2001, BS EN 61010-2-032: 2002, BS EN 61010-031: 2002, 300 Vrms, Category III, Pollution Degree 2, Use of the probe on uninsulated conductors is limited to 300 V AC RMS or dc and frequencies below 1 kHz. EMC Standards: EN 61326: 1998 +A1, A2, and A3. Measures 71mm width by 183mm height by 25mm depth.

Manufacturer: Digilent Brand: Digilent

The Digilent Electronics Explorer board (EE board) includes all of the test and measurement equipment needed to design and test analog and digital circuits of all types. Built around a large solderless breadboard, the EE board includes oscilloscopes, waveform generators, power supplies, voltmeters, reference voltage generators, and thirty-two digital signals that can be configured as a logic analyzer, pattern generator, or any one of several static digital I/O devices. All of these instruments can be connected to circuits built on the solderless breadboards using simple jumper wires. Designed for daily use and intended for every student to own, the EE board combines everything needed to design and test circuits in a single "all in one" device. Even in introductory classes, students can complete, test, and analyze real circuit designs as a part of every homework assignment. No more once a week labs; now every student can complete designs in virtually any setting - any residence can be a complete, 24-hour design studio! The EE board is powered by the free, PC-based WaveFormsTM software that makes it easy to acquire, store, analyze, produce and reuse analog and digital signals. WaveFormsTM runs well on virtually any notebook PC, including low-cost Netbooks. A high-speed USB2 connection ensures all EE board instruments respond in near real-time. WaveFormsTM data files are stored using standard formats, making it easy to share data between instruments, and to export data to word processors or graphics editors. This means well documented student lab/project reports can be completed using standard office tools, and submitted electronically. Additional Product Information

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-705

Loop Calibrator is a cost-effective, integrated solution for calibration, repair and maintenance of current loops. A large display and simple, pushbutton interface for ease of use. Simultaneous mA and percent readout for quick, easy interpretation of readings. mA accuracy of 0.02 percent. Push button 25 percent steps for fast, easy linearity checks. Save time over traditional knob type controls. "Span Check" for fast confirmation of zero and span. Selectable slow ramp, fast ramp, and step to provide smooth outputs for valve slewing and loop functional tests. 24 volt internal loop supply, so you can power and read a transmitter at the same time without carrying a DMM. Single 9V battery that is easily changed. 0 - 20 mA or 4 - 20 mA default start up modes. 0.02 percent accuracy and 0.001 mA resolution. Simultaneous mA and percent of span display. Selectable step or ramp outputs. 24V Loop supply with mA measure. 0-28 VDC measurement to check Loop Voltage. Easy battery exchange without opening the case. Compact case with separate protective holster. 3 year warranty. Current measurement: : 0 to 24 mA range, 0.001 mA resolution, 0.02 percent Rdg + 2 LSD accuracy. Voltage measurement: : 0 to 28V DC range, 1 mV resolution, 0.025 percent Rdg + 2 LSD accuracy. Loop power: while measuring mA, 24V. Operating temperature: -10/55 degree C. Storage temperature: -40/60 degree C. Measures 152mm length by 70mm width by 41mm depth. Loop calibrator including: AC70A alligator clips, C10 protective yellow holster with Flex-Stand, instruction sheet, TL75 safety-designed test lead set, NIST- traceable calibration report and data. Weight: 340g.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-707

Loop Calibrator is a high performance solution for calibration, repair and maintenance of current loops. The new "Quick Click" knob making it extremely fast and easy to use. Large display and simple, quick-click interface for easy one-handed operation. Simultaneous mA and percent readout for quick, easy interpretation of readings. mA accuracy of 0.015 percent, superior to other loop calibrators in this price range. 1 microampere resolution for mA source, simulate and measure. Push button 25 percent steps for fast, easy linearity checks. 0-100 percent "span check" for fast confirmation of zero and span. Selectable slow ramp, fast ramp, and step ramp to provide smooth outputs for valve slewing and loop functional tests. 24 volt internal loop supply, so you can power and read a transmitter at the same time without carrying a DMM. Measures V dc to 28V. Single 9V battery that is easily changed without braking calibration seal 0 - 20 mA or 4 - 20 mA default start up modes. Innovative output adjustment dial with 1 microampere and 100 resolution. HART mode connects 250 O resistor in series with 24 V loop for compatibility with HART communicators. Current measurement: : 0 to 24 mA range, 0.001 mA resolution, 0.015 percent Rdg + 2 LSD accuracy. Voltage measurement: : 0 to 28V DC range, 1 mV resolution, 0.015 percent Rdg + 2 LSD accuracy. Loop power: while measuring mA, 24V. Operating temperature: -10/55 degree C. Storage temperature: -30/60 degree C. Measures 152mm length by 70mm width by 41mm depth. Including: protective yellow holster with test lead storage, instructions sheet (14 languages), single 9V alkaline battery, test leads and alligator clips, NIST- traceable calibration report and data. Weight: approx. 330 g (21 oz)

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-355

The Fluke 355 digital clamp-meter is a true RMS sensing, auto-ranging multimeter for measuring current, voltage, frequency, and resistance in electrical testing applications. It has a clamp that measures AC (alternating current) and DC (direct current) to 2,000A (amperes) (1,400A AC RMS). The clamp has two jaws that can close around an electrical conductor up to 58mm (2.3 inches) in diameter to measure the current of large or multiple conductors without touching or interrupting the circuit. A set of test leads is included for measuring AC voltage to 600V, DC voltage to 1,000V, frequency to 1kHz (kilohertz), and resistance to 400kΩ (kilohms). The test leads are silicone-insulated for flexibility and resistance to heat and cold. The meter has a rotary switch to select the property to measure, and an LCD with a backlight for visibility in low light that turns off automatically after five minutes.The meter's inrush current function analyzes the surge current at the startup of motors and other inductive loads to provide accurate, stable measurements. It features a low-pass filter that reduces high-frequency interference to allow accurate measurements of complex wave shapes. The minimum/maximum function toggles to display the lowest, highest, and average readings. To aid documentation of readings and capture readings in tight spaces, the data hold function keeps the reading on the display after disconnecting from the circuit. A continuity buzzer confirms that the circuit conducts electricity. The unit operates on six 1.5V AA batteries, and turns off automatically after 20 minutes of non-use to conserve battery life. It has a low-battery indicator that signals when the battery needs to be replaced.This true RMS (root mean square) sensing meter provides accurate readings when measuring linear or non-linear loads, regardless of waveform. It is auto-ranging, so it automatically selects the appropriate operating range for the property being measured. Accuracy and resolution specifications vary according to the range bein...

Manufacturer: Fluke Brand: Fluke Model: 4550041

Fluke 820 LED Stroboscope.

Manufacturer: Fluke Brand: Fluke Model: 4697049

Part of the Fluke Performance series and offers affordable quality images combined with easy to use, point and shoot technology.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-1587 MDT

The Fluke 1587 MDT advanced insulation and motor drive troubleshooting kit is designed for troubleshooting and preventive maintenance applications including three-phase motors, cables, switch gear, and in applications where testing is required without the need to break the circuit. The kit includes the Fluke 1587 digital insulation multimeter, Fluke i400 current clamp, and Fluke 9040 phase rotation indicator. The Fluke 1587 digital insulation multimeter (also known as a multitester) is a true RMS, auto- and manual-ranging meter insulation resistance, current, voltage, and resistance for testing line insulation in telecommunications applications. The insulation test voltage settings of 50V, 100V measure resistance from 0.01 to 100 megohms. The meter also measures capacitance, frequency, and resistance. Temperature is measured using a K-type thermocouple (included). A diode test detects correct functioning of a circuit's diodes. A low-pass filter provides accurate AC voltage and AC frequency measurements on inverters and variable-frequency motor drives by blocking unwanted voltages. Live circuit detection increases user safety by preventing insulation tests when voltages exceed 30V, and auto-discharge of capacitive voltage increases user protection. An audible continuity sensor confirms a circuit conducts electricity. The LCD is backlit for readability in low light. A hold function freezes the reading on the display. An alarm sounds when the test leads are connected to the wrong jack for the measurement being taken. The unit automatically turns off after 20 minutes of nonuse to conserve battery life or can be disabled for extended readings, and a low-battery indicator signals when the meter's batteries need to be replaced. The meter included a set of detachable test leads, a remote probe, alligator clips, a hard case, and instructions. This true RMS (root mean square) insulation multimeter provides accurate readings when measuring linear loads, such as standard induction motors and incandescent lights, where the c...

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-985

The new Fluke 985 Particle Counter is the preferred choice for HVAC and IAQ professionals. From filter testing to IAQ investigations, the Fluke 985 is the portable solution for determining airborne particle concentrations. Use the Fluke 985 to immediately respond to occupant complaints, or as part of a comprehensive preventive maintenance program. Drive additional business by demonstrating the need for maintenance and repair. With a large screen, intuitive icons for navigation and on-screen data presentation, the Fluke 985 allows users to run more tests quickly, with less time spent cycling through screens to obtain the data. The Fluke 985 is lightweight and easy to use in any position and with easy data export options using USB cable, memory stick. it's easy to review and analyze the data anywhere and anytime. Assess air quality more easily and accurately. Six channels and particle size range of 0.3 - 10.0 micron: Assures accurate measurements even for critical locations requiring ISO Class 5 - 9 certification. Ultra-lightweight and ergonomic design: Promises easy single-hand operation in tight or awkward spaces with less operator fatigue. Long battery life: Ten hours of standard-use battery life to last a full work day. Large 3.5 QVGC Color display: Easy navigation and viewing with the intuitive icons and large font options. 10,000 record storage: Quick access to historical data. On-screen data presentation: Data can be viewed in a traditional tabular or trend graph view at the user's preference. Personalized setting and configurations: Customizable settings for the display, sample methods, and alarm settings for sample count. Data export options: Download data to a PC using a USB memory stick, USB cable or Ethernet connection. No special software is required to download or view data.