Electrical Testing - Page 106

Manufacturer: AEMC Brand: AEMC Model: 2113.33

The AmpFlex is a flexible AC current probe composed of a flexible sensor and an electronic module. The flexible sensor permits measurements on conductors where standard clamp-on probes cannot be used. Measurement range is 5 to 30,000A. Output signal is 1mV/A & 0.1mV/A. Sensor length is 24".

Manufacturer: GW Instek Brand: GW Instek

' 50 MHz Bandwidth with 2 Input Channels. 250MSa/s Real-Time and 25GSa/s Equivalent-Time Sampling. 4k Memory Length per Channel. Peak Detect as Fast as 10ns. Save/Recall of 15 Front Panel Settings & Waveforms. 5.7" TFT Color Display. 19 Auto Measurements. Arithmetic Operators - Add, Subtract, FFT. USB Port for PC Connection. Data Logger. Limited Lifetime Warranty through GW Instek. Image represents the GDS-1000-U series, and is for illustration purposes onlySpecifications:Display5.7" TFT LCD ColorBandwidth (MHz)50Number of Channel2Memory Depth4k PointsSample Rate250MSa/s (RTS); 25GSa/s (ETS)Vertical Resolution 8-bitVertical Sensitivity 2mV/div ~ 10V/divTime Base Range1ns/div ~ 50s/divInput Impedance Selection 1MOAuto Measurement19Waveform Memory15 Panel Setup Memory15InterfaceUSB Host/DevicePower SourceAC 100V ~ 240V'

Manufacturer: Mill-Max Brand: Mill-Max

Contact Probes LOOSE CONTACT Initial Height .375"

Manufacturer: LeCroy Corporation Brand: LeCroy Model: WSXS-I2CBUS TD

Advanced software algorithms deconstruct the waveform into protocol information, then overlay the decoded data on the waveform. Decode information condenses or expands depending on the timebase/zoom ratio setting, so understanding messages is easy. Various sections of the protocol are color-coded to make it easy to understand, especially for users new to I2C serial data. The decode operation is fast-even with long acquisitions. The user can choose to decode into hex, binary, or ASCII formats. Completely isolate specific I2C message events for better understanding and debug. Use a conditional DATA trigger to select a range of DATA values to trigger on, not just a single DATA value. Oftentimes, I2C utilizes DATA bytes to specify sub-addresses for accessing memory locations in EEPROMs. Conditional DATA trigger allows triggering on a range of DATA bytes that correspond to reads or writes to specific sub-address memory blocks in the EEPROM. It can also aid in monitoring DATA outputs from I2C-based sensors, such as analog-to digital converters, and triggering when DATA is outside a safe operating range. In both cases, verifying proper operation becomes a simple task. Of course, all the basic I2C triggering capability you would expect is also included. Turn your oscilloscope into a protocol analyzer with the Table display of protocol information. Custom configure the table to display only the information you want, and export table data to an excel file. Touch a message in the table and automatically zoom for detail. In all cases, the table never obscures your waveform data. Compatible with TD (Trigger and Decode) Option compatible with all WaveMaster 8 Zi/Zi-A, WavePro 7 Zi/Zi-A, WaveRunner 6 Zi, WaveRunner Xi and WaveSurfer Xs. D (Decode) Option fully compatible with WaveRunner 6000, WavePro 7000, and WaveMaster 8000 Series.

Manufacturer: GW Instek Brand: GW Instek Model: LCR-12

4 Wire test lead with kelvin clip. Odd-shaped components support. Suitable for low R or high C. For LCR-8000G and LCR-800 series LCR meter. Frequency: DC to 10 MHz. Maximum voltage: +/- 35V.

Manufacturer: Virtins Technology Brand: Virtins Technology

1. Package Contents: (1) VT DSO-2A20E unit with a hardware activated Multi-Instrument Standard software license. (2) 2 × 100MHz Oscilloscope Probe P6100 with two switchable positions: × 1, × 10. (3) 1m Signal Generator Test Lead. (4) 1.5m USB cable. (5)CD (contains the copy-protected Multi-Instrument software). 2. Applications: (1) Ordinary oscilloscope, spectrum analyzer and signal generator functions, all of which work simultaneously. (2) DUT (Device Under Test) analysis such as frequency response. (3) High resolution and low noises at lower sampling rates, 12 voltage ranges from full scale +/-10mV to +/-50V, and support of sensor calibration make it suitable to work as a data acquisition device. (4) Signal Recording and Replaying.....

Manufacturer: UNI-T Brand: UNI-T UTG2025A

Specification:UTG2025A Channels:2 Max.Sample Rate:200MS/s Max.Output Frequency:25MHz Frequency Resolution:1 μHz Vertical Resolution:14 bits Max. Arb Memory Depth:1Mpts Waveform:Sine,Square,Ramp,Triangle,Pulse,Noise,DC,Arb Output Amplitude Range:1mVpp～10Vpp （50Ω）；2mVpp～20Vpp （High Z） Modulation Types:AM、FM、PM、ASK、FSK、PWM、Sweep、Burst Interface:USB Device, USB Host, LAN (UTG2062A ) General Characteristic Power:100-240VAC, 40-440Hz Display:4.3 Inches 64K Color TFT LCD, 480×272 Product Color:White and Gray Product Net Weight:3.2 Kg Product Size:231mm × 94mm × 283mm Standard Accessories:BNC Cable,Power Cord , USB Cable,PC Software CD

Manufacturer: Instek Brand: GW Instek Model: USG-2030

Instek USG-2030 2000MHz to 3000MHz RF Signal Generator GW Instek debuts the brand new USG-Series RF signal generator, which comes with five models to meet users' requirements and is a pocket-sized, and USB interface compatible RF signal generator with the frequency range from 35MHz to 4400MHz. The USG-Series provides continuous wave (CW) signal outputs without any signal modulation function. The built-in electronic attenuator of the USG-Series allows an adjustable power range from -30dBm to 0dBm. The USG-Series has several operational modes including fixed frequency, frequency sweep, frequency hopping, and power sweep. The USB-Series RF signal generator, with the frequency bandwidth limitation, provides lower harmonic output performance.   Test Result of Similataneous Power Sweep and Frequency Sweep   The GW Instek USG-Series RF signal generator is a pocket-sized and USB interface compatible RF signal generator. It covers the frequency range from 335MHz ~ 4400MHz. The USG-Series provides continuous wave (CW) signal outputs without any signal modulation function. The built-in electronic attenuator of the USG-Series allows an adjustable power range between -30dBm to 0dBm. The USG-Series has several operational modes including fixed frequency, frequency sweep, frequency hopping, and power sweep.   Easy to Use Graphical Interface with Numeric Setting   A USG CD-ROM provides dedicated PC application programs, which were developed under JAVA software structure. This USG PC application program supports operating systems such as Windows 2000/XP/Vista/7/8, Linux & Mac OS X through the USB interface.   USG Android APP   Users can download USG APP to smart phone or tablet (or smart phone) and USG. The Android APP application software for the USG signal generator is available on Google Play Store

Manufacturer: Mueller Electric Brand: Mueller Electric

Test Plugs & Test Jacks Adptr-BNC Female to

Manufacturer: IDI Brand: IDGroup

Contact Probes HDLESS 30 DEG SPEAR