Electrical Testing - Page 143

Manufacturer: Megger Brand: Megger Model: GA-00380

The Megger four-piece sensing cable kit includes a 1.6' (0.5 m) current cable, connection plate, voltage sensing cable, and ground cable for use with the Megger MOM2 microhmmeter or other compatible low-resistance ohmmeters. The kit is used for taking four-wire resistance measurements, which are more accurate than two-wire resistance measurements and allow low resistance values to be detected.A test probe, test lead, test prod, or scope probe transmits an electrical signal to a testing device for display and analysis. Designs range from simple test leads with probe-style or clamp-on tips to more complex oscilloscope probes and current detectors. Some test probes, such as basic test leads, have wires with tips for connecting to test equipment. Other test probes, such as voltage detectors, are built into the meter. Depending on what is to be tested, the probe might either be passive or have active parts that require external power to operate. Some probes require contact for testing, while some are capable of taking measurements from a distance. Some also have finger barriers, insulation, or other features to help protect the operator's hand from electrical shock and burns. Test probes are rated according to the amount of voltage, current, temperature, or other input they can measure. When choosing a test probe, the maximum amount of input that the probe can measure should match or exceed both the maximum amount that can be tested by the test equipment, as well as that of the property expected to be present in the application.Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger, Biddle, States, and AVO. The company, founded in 1889, is headquartered in Dover, England, and meets International Organization for Standardization (ISO) 9001:2008 standards.

Manufacturer: Alltronics LLC Brand: AnaTek Instruments Model: BESR

Our Blue ESR Meter has been very popular since 2007. This is the latest Bob Parker design and successor to the famous Dick Smith MKII ESR and Low Ohms Meter. This handy and affordable ESR meter measures capacitor equivalent series resistance (ESR) for capacitors >1uF and up to 450V. ESR is a very important quality and performance characteristic of capacitors greater than 1 uF. This meter makes measurements which are often impossible to check with capacitance meters. It also can be used to assess health for LV alkaline/rechargeable batteries, find shorts on PCBs, inductive coil shorts and for assessing incoming quality assurance of components and can also be used to test the low resistance grounding of ANSI/ESD S20.20, ANSI/ESD S6.1, ESD TR20.20 and compliance verification for grounding systems. Includes quality test leads with banana jacks, basic alligator clips, easy-access battery compartment and on-board diagnostics to detect errors. You can add the optional croc clips and/or probes or use your own. This has the MkII firmware, Bob's latest version developed over many years. It can accurately test ESR down to an internal battery voltage of 5.5 volts. It has a full 1yr warranty on parts and assembly from Anatek.

Manufacturer: IDI Brand: IDGroup

Contact Probes R-3-SC

Manufacturer: Probe Master Brand: Probe Master Model: 4901-3KRA

Oscilloscope probe with readout actuator, 125MHz, 1X/10X, 600V, 6.6ft, DELUXE KIT

Manufacturer: B\u0026K Precision Brand: B\u0026K Precision

Function Generators & Synthesizers AUDIO GENERATOR

Manufacturer: Amprobe Brand: Amprobe Model: AMPRB-ET4

This kit contains a number of useful accessories for earth testing, and is the perfect accompaniment to many of Amprobe's products.

Manufacturer: LeCroy Corporation Brand: LeCroy Model: PACC-ZD002

Solder in lead for ZD differential probe.

Manufacturer: Knipex Tools LP Brand: KNIPEX Tools Model: 98 60 04

Voltage tester.

Manufacturer: Omniprobe Brand: Electron Microscopy Sciences

Custom tip designed from tungsten. Tip radius is 0.5µm with 13º taper angle for maximum lifetime service.

Manufacturer: 3M Brand: 3M

3M(TM) FP-301 is a heat shrinkable flexible polyolefin tubing that offers an outstanding balance of electrical, physical and chemical properties for a wide variety of industrial and military applications. Rated for 275(deg)F(135(deg)C) continuous operation. FP-301 tubing is typically used as a shrink-fit electrical insulation over cable splices and terminations. It is also used for lightweight wire harness covering, wire marking, wire bundling, component packaging and fire resistant covering. FP-301 clear tubing provides excellent visibility for component packing. All FP-301 tubing is split resistant, mechanically tough, easily marked and resists cold flow. FP-301 is available in black, white, red, blue, yellow and clear in the standard lengths of 6-inch (15,2 cm) cut pieces, 48-inch (1,21 m) and small (8.5-inch core diameter) spools of 50 (15,24 m) and 100 (30,48 m) feet. Four-foot lengths of green tubing are available in sizes 1/16 inch to 1/2 inch. The Assorted Color Kit has a total of 133 pieces and contains seven colors: black, red, white, yellow, blue, green and clear. The Black Kit contains 102 pieces, all 6" (512,4 mm) lengths (see chart below.)Additional sizes, colors and put-ups are available -please contact your 3M Electrical Products Sales Representative. Application Specifications: UL Recognized and CSA Certified at 600 volts at 257(deg)F(125(deg)C); UL File No. E-39100 and CSA No. 38227. MIL-I-23053/5, Class 1,2. AMS 3636 (Type I) and AMS 3637 (Type II). To Order: Reference specific product size, color and description on the following pages. Example: FP-301-1/4, white 6" (15,2 cm) pieces.