Electrical Testing - Page 214

Manufacturer: IDI Brand: IDGroup

Contact Probes HEADED SERRATED

Manufacturer: Fluke Brand: Fluke Model: 4542273

The Fluke Series Battery Analyzer is ideal test tool for maintenance, troubleshooting and performance testing of individual stationary batteries and battery banks used in critical battery back-up applications.

Manufacturer: Fluke Corporation Brand: Fluke Model: SCC190EFG

C190 Protective hard shell carrying case for 190 series ScopeMeter. OC4USB Optically isolated USB adapter/cable. SW90W/034EFG FlukeView software for Windows. English, French and German language.

Manufacturer: KEYSIGHT TECHNOLOGIES Model: U1733C

With the U1733C you can perform quick, basic LCR measurements at your convenience. Now you can measure at frequencies as high as 100 kHz, a capability that is typically found only in benchtop meters. With the auto identification, Ai which conveniently displays component type and detailed component analysis such as Z, ESR, DCR, you can get measurements done faster. Better yet, the battery lasts up to 16 hours, ideal for testing on the go. 20,000 counts resolution 0.2% accuracy Wide LCR ranges with 5 selectable test frequencies (100Hz, 120Hz and 1kHz, 10kHz and 100kHz) Detailed component analysis with DCR, ESR, Z, D and Q functions IR-to-USB connectivity for data logging to PC

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-787CAL120

Fluke 787CAL120 USA Calibration Module The Fluke 787CAL module permits users and service facilities to perform automated MET/CAL verifications and calibrations of the Fluke 787 ProcessMeter. Application: The calibration module provides a 9 volt dc supply to the 787. At the same time, it facilitates RS232 communication from the PC running MET/CAL to the 787 over the battery leads of the 787. Note: An installation of MET/CAL Calibration Software plus appropriate calibration hardware must be provided by the user.

Manufacturer: Fluke Corporation Brand: Fluke Model: I3000S FLEX-36

The i3000s Flex is an ac current clamp utilizing the Rogowski principle. It can be used to measure currents up to 3000 A when used in conjunction with oscilloscopes, recorders or data loggers. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas. Three ranges: 30A, 300A and 3000A, 1, 10 or 100 mV/A output. Ideal for current measurement on thick and hard to reach conductors without breaking the circuit. Maximum conductor diameter 178mm. CAT III 600V safety rating. Output sensitivity (AC-coupled): 100 mV, 10 mV, 1 mV per A. Load impedance: 100 kilo ohm minimum. Accuracy at +25 degree C: +/-1 percent of range (45 Hz to 65 Hz). Linearity 10 to 100 percent of range: +/-0.2 percent of reading. Noise: 8 mV AC rms (30 A), 2 mV AC rms (300A, 3000A). Frequency range: 10 Hz to 50 kHz (-3 dB). Phase error: less than +/-1 degree (45 Hz to 65 Hz), +/-10 degree (at 20 kHz). Position sensitivity with cable greater than 25 mm from the coupling: +/-2 percent of range. External field with cable greater than 200mm from the head: +/-1 percent of range. Power supply: 2 x AA/MN 1500/LR6 Alkaline, 400 hours, low battery indicator or dedicated external power supply. Temperature Coefficient: +/-0.08 percent of reading per degree C. Working voltage: 600V AC rms or DC. Head circumference: 915mm. Head cable diameter: 14.3mm. Head bend radius: 38.1mm. Cable length (head to electronics): 2m. Output connection: 0.5m cable terminated with safety BNC connector. Supplied with 4mm safety plug adapter. Operating temperature range: -20 to +90 degree C (-4 to 190 degree F) (head), -20 to +85 degree C (-4 to 185 degree F) (electronics). Storage temperature range: -40 to +105 degree C (-40 to 221 degree F) (head), -20 to +85 degree C (-4 to 185 degree F) (electronics). Operating humidity: 15 to 85 percent (non-condensing).

Manufacturer: AEMC Brand: AEMC Model: 2126.84

The High Frequency MiniFlex Probe is a compact flexible AC current measurement device composed of a flexible sensor and an electronic module. It is designed to measure AC Current from 5Hz to 1MHz. The flexible sensor permits measurements on conductors where standard clamp-on probes could not be used.

Manufacturer: Rigol Brand: Rigol Model: DP821

Dual Output, 140 W Power Supply     Remote Controls Methods User-defined Programming You can program and control the instrument using the SCPI (Standard Commands for Programmable Instruments)   Send SCPI Commands via the PC Software You can control the power supply remotely by sending SCPI commands via the PC software (Ultra Sigma) provided by RIGOL.. SCPI Command Overview SCPI (Standard Commands for Programmable Instruments) is a standardized instrument programming language that is built upon the standard IEEE488.1 and IEEE 488.2 and conforms to various standards (such as the floating point operation rules in IEEE754 standard, ISO646 7-bit coded character for information interchange (equivalent to ASCII programming)). This section introduces the syntax, symbols, parameters and abbreviation rules of the SCPI commands. SCPI Status Registers All the SCPI instruments execute the status register operations in the same way. The status system records the various instrument states into three register sets: status byte register, standard event register and questionable status register sets. The status byte register records the advanced summary information reported by other register sets. The SCPI status systems of the DP800 series multi-channel models. Build Remote Communication You can build the remote communication between DP800 and PC over USB, LAN, RS232 or GPIB (option, can be extended via the USB-GPIB interface converter) interface.   OVERVIEW   The DP800 Series Power Supplies combine the ability to source, analyze, and coordinate over time in a powerful new package. The DP800 Series is a family of linear power supplies systems with 3 outputs and up to 195 Watts in total. With one channel isolated users can reconfigure instruments into any number of systems or applications

Manufacturer: Applied Materials (Amat) Brand: Applied Materials (Amat)

Rf Isolator, Mircowave Clean

Manufacturer: Vetus Brand: Hantek Color: Grey

Feature 4 Channel Oscilloscope+8 Channel Logic Analyzer + 25MHz Arb. Waveform Generator(MSO5074FG). Abundant Trigger type: Video, Edge, Slope, Pluse Width, Overtime, Alternative, Code-type, Duration, Queue, Repeat trigger. Large 7 inch 64K color Display, WVGA: 800*480. USB host and device connectivity, standard. Ultrathin desigh, handy volume, easily portable. Oscilloscope 1Gsa/s Real Sample Rate; 4 Channels Oscilloscope; 70MHz Bandwidth, 1MRecord Length; 32 automotive measurement and FFT Analysis for Simplified Waveform Abalysis. Logic Analyzer 8 Channles Logic Analyzer; 500MHz Sample Rate 1MRecord Length Arb. Waveform Generator 25MHz Arb. Waveform Generator Output(Sine wave up to 75MHz) 200MSa/s Sample Rate; 12bit Pattern Generator 50MHz Frenquery Counter