Electrical Testing - Page 280

Manufacturer: Fluke Brand: Fluke Model: Fluke-805 FC

Make go or no-go maintenance decisions with confidence. The Fluke 805 FC Vibration Meter is the most reliable vibration screening device available for frontline mechanical troubleshooting teams that need repeatable, severity-scaled readings of overall vibration and bearing condition.

Manufacturer: Fluke Brand: Fluke Model: 281-U 115V

The fluke 281 1 channel. 40 ms/s arbitrary waveform generator and waveform manager plus software has waveform creation and editing features incorporated within the instrument. These universal waveform generators combine many generators in one instrument. Their extensive signal simulation capabilities include arbitrary waveforms, function generator, pulse/pulse train generator, sweep generator, trigger generator, tone generator, and amplitude modulation source. 40 MS/s maximum sampling speed. 16 MHz function generator. 10 MHz pulse generator. Pulse train pattern generator. Arbitrary waveforms of up to 65 k points. Powerful modulation capabilities. Built-in trigger generators. Waveform manager plus for windows software. Multiple standard waveforms recalled from internal memory. LCD display. +/- 14 percent accuracy. 115V supply voltage. 50/60 Hz frequency. Measures 335mm length by 212mm width by 130mm height.

Manufacturer: AEMC Brand: AEMC Model: 6240

The AEMC 6240 digital microohm meter with data analysis software is a manual-ranging four-input meter with six test current and resistance ranges for precise, low-resistance measurements from 1 microohm (μΩ) to 400 ohms (Ω) of switches, relays, test wires, cables, printed circuit boards, and other electrical components. Four input terminals enable Kelvin-type, four-wire resistance measurements, which are more accurate than two-wire resistance measurements. The meter includes PC software for configuring the meter, storing and analyzing data, generating reports, and performing temperature compensation of readings. The software is compatible with Windows XP, Vista, 7, and 8, and requires at least 80MB of hard disk space. A cable with USB connector is included for connecting from the meter's optical interface to a PC. The meter's memory function allows storage of up to 99 readings. The polarity reversal function improves reading accuracy by compensating for interference from thermal electromagnetic fields (EMF). When measurement is complete, residual voltage will be automatically discharged from the device under test. Built into a sealed field case, the meter has a 4,000-count LCD with a backlight for visibility in low light. It operates on a rechargeable 6-volt nickel-metal hydride (NiMH) battery pack (included) and has a low-battery indicator that signals when the battery needs to be recharged. It comes with a set of test leads with Kelvin clips, data analysis software, a pad of 50 test results forms, an interface cable with USB and optical connectors, a 115V power cord, two 12.5A replacement fuses, a carrying bag, and instructions. Milliohm meters are commonly used for electrical maintenance and testing in industries such as heating, ventilation, and air conditioning (HVAC), transportation, telecommunications, power plants, and utilities, among others.This manual-ranging meter allows the user to select the operating range for measurements. Accuracy and resolution specifications vary according to the range...

Manufacturer: Megger Brand: Megger Model: 6111-429

The Megger DLRO10 series digital microhmmeter measures resistance in switch and contact breakers, bus-bar and cable joints, battery systems, resistive components, and other electrical component links. The meter is autoranging and digital for safety and ease of use. The auto current reversal function cancels out thermal electromagnetic fields (EMFs) for more accurate test results. The unit has a noise limit set at 100mV. An indicator light illuminates when the noise limit has been exceeded. The unit automatically measures continuity when it is connected to a circuit. The DLRO10 series is used by electricians and electrical contractors.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Electrical test meters display information either in analog form using a needle that moves on a calibrated scale, or in digital form on an LED screen. Meters have electrical properties that are to be measured and the anticipated range of results, and should have a rating that is higher than the maximum value of the anticipated range. Meters measure electrical properties and are safety rated to measure a specific range of results. The range on the meter should be higher than the maximum anticipated value to be measured. An electrical test meter has multiple settings corresponding to potential ranges of values for the properties it can measure. A manual ranging meter requires the operator to flip through different settings until the correct range is reached. An autoranging meter cycles through range settings automatically until it reaches the correct range. Megger manufactures equipment for cable fault locating, prot...

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-1550C

The Fluke high-voltage digital megohmmeter is an insulation tester with preset and adjustable test voltages for measuring insulation resistance to 1TΩ (2TΩ for 10kV models) to indicate the condition of windings or cables in motors, switchgears, electrical installations, and other insulated equipment, and it also measures leakage current to 2 milliamperes (mA), capacitance to 20μF, and AC and DC voltage to 600V, signaling when a voltage greater than 30V is detected. In addition to the preset test voltages of 250V, 500V, 1,000V, 2,500V, 5,000V, plus 10,000V for the 10kV models, test voltages can be adjusted in 50V increments to 1,000V and 100V increments above 1,000V. Its PI/DAR (polarization index/dielectric absorption rate) function automatically calculates PI and DAR, which are measurements over time that give a truer indication of insulation condition than single-point measurements. The meter can perform timed tests up to 99 minutes, adjustable in 1-minute increments, and has storage for up to 99 test results. Stored results can be uploaded to a PC with the included FlukeView Forms Basic software. The software is compatible with Microsoft Windows 2000, XP, and Vista. For improved accuracy during high-resistance testing, the guard terminal eliminates interference from leakage current. The meter has an LCD that shows the reading numerically and in a bar graph. Megohmmeters are commonly used for electrical maintenance and testing in industries such as HVAC, transportation, manufacturing, mining, and utilities, among others. The meter is rated for category (CAT) IV installations to 600V, which covers equipment at the origin of the installation, such as electricity meters and primary over-current protection equipment, and CAT III installations to 1,000V, which covers equipment in fixed installations, such as switches in the fixed installation and some industrial equipment that is permanently connected to the fixed installation. The unit has a low-battery indicator that signals when the battery needs to be r...

Manufacturer: B&K Precision Corporation Brand: B&K Precision Model: 2650A

BK Precision’s 2650A series handheld spectrum analyzers are compact, light weight, and cost-effective spectrum analyzers for quick and precise signal investigations, especially away from the bench. At a weight of only 1.8 kg (4 pounds), the 2650A series are by far the lightest full-featured spectrum analyzer available, yet they deliver performance and features comparable to full-size bench spectrum analyzers and can operate up to 4 hours on a single battery.

Manufacturer: solu Brand: Solu Color: red

About us (Solu ®), Professional factory of circuit boards for Arduino, welcome to our store for more choices with best price. What we pursue is your satisfication of our service, not just for our goods.For any reason you are unsatisfied with our product at any time, simply contact support for exchange or refund. we will reply you about any question you ask within 24 hours Specifications : Measuring Range: DC 2.50~30V Two-wire Access Measurement Accuracy: 0.1V Refresh Rate: ¡Ý200mS/times Display: 0.28" LED Digital Tube Display Color: Red Operating Temperature: -10¡ãc ~ + 65¡ãc Convenient access to the car, battery car, motorcycle line, reverse connect protection function Power supply same source, self-power Size: 3.1 x 1.2 x 0.9cm/1.22" x 0.47" x 0.35" (Approx.) Wiring: Red: Power Supply +, Measure Voltage +, (2.50~ 30V DC) Black: Power Supply -, Measure Voltage - Package Includes : * 1 x Digital Voltmeter Panel

Manufacturer: GB Electrical Brand: Gardner Bender Model: GMT-12A Color: Black

Testing equipment can be put to good use ensuring that electrical equipment is properly installed and safe to operate. Faulty installations can be lethal; the condition of electrical installations can be established when contractors use test equipment. Pocket sized analog tester. Tests voltage, dc voltage, dc current, resistance, continuity and batteries.

Manufacturer: JINHEZO Brand: JINHEZO Model: na Color: 6 PCS White

To protect your batteries, get this Clear Color 6 PCS of AA / AAA 4 Cell Battery Storage Case.

Manufacturer: Extech Brand: Extech Model: TL803

EXTECH INSTRUMENTS TL803 TEST LEAD SET, CATIII, 1KV