Electrical Testing - Page 386

Manufacturer: Pomona Electronics Brand: Pomona Electronics

Test Plugs & Test Jacks RED PANEL JACK BU-31609-2

Manufacturer: Fluke Corporation Brand: Fluke Model: EI-162AC

Fluke EI-162AC Clip-on Current Transformer (Inducing) The EI-162AC Clip-On Current Transformer (Inducing) is used along with the Fluke 1623 or 1625 to perform Selective and Stakeless testing. Selective testing means using one clamp along with earth ground stakes to provide earth ground loop resistance values for one earth ground electrode. Stakeless testing uses two clamps to perform earth ground loop resistance measurement without stakes. Both tests have the advantage of providing measurements with no disconnection from the grounding system! Safer and quicker.

Manufacturer: Gossen Metrawatt Brand: GOSSEN METRAWATT

In addition to multimeter hardware, the BD pack includes everything required for setting up a single-channel recording system: BD232 Interface adapter METRAwin10 software RS232 interface cable The infrared interface allows for electrically isolated data transmission between PC and multimeter. METRAwin 10 analyzes and displays acquired data. It cannot be used for online recording with type SI232-II adapters.

Manufacturer: Kyoritsu Brand: Kyoritsu Model: 8124

Kyoritsu 8124 load current clamp sensor. In order to monitor energy saving and to control the electric facilities, it is essential and imperative to control the leak and load currents from mains and branch power lines up to the equipment. Clamp sensor is easy to carry and simple to install. Load current detection type clamp sensors provide superior characteristic in phase for the use of power meter. Rated current 1000Amp AC. 68mm conductor size. Output voltage: AC 500mV/1000A (AC 0.5mV/A). Accuracy: +/- 0.5 percent rdg +/- 0.1mV (50/60Hz), +/- 1.0 percent rdg +/- 0.2mV (40Hz to 1kHz). Phase shift within +/- 1.0 degree. Output connector: Mini-DIN 6-pin. 0 to 50 degree c temperature range. Withstand voltage: 5350V AC for 5 seconds. Approximate 3m cable length. Approximate 1 ohm output impedance. Accessories includes: portable case, instruction manual, cable marker. Measures 186 mm length by 129 mm width by 53mm depth.

Manufacturer: Harwin Brand: Harwin

Contact Probes 1.27mm SPRING PROBE 2 PART CONVEX HEAD

Manufacturer: Megger Brand: Megger Model: 6111-022

The Megger 6111 series duplex test lead with helical spring-point duplex hand spikes is for use with Megger DLRO10HD, DLRO10, DLRO10X, and BT51 digital microhmmeters. This duplex test lead measures both current and resistance when taking four-wire resistance measurements, which are more accurate than two-wire resistance measurements and allow low resistance values to be detected. The helical spring-point hand spikes compress and rotate to make contact with a conductor. There is 0.4" (10 mm) between the current and potential probe tips on the duplex hand spikes.A test probe, test lead, test prod, or scope probe transmits an electrical signal to a testing device for display and analysis. Designs range from simple test leads with probe-style or clamp-on tips to more complex oscilloscope probes and current detectors. Some test probes, such as basic test leads, have wires with tips for connecting to test equipment. Other test probes, such as voltage detectors, are built into the meter. Depending on what is to be tested, the probe might either be passive or have active parts that require external power to operate. Some probes require contact for testing, while some are capable of taking measurements from a distance. Some also have finger barriers, insulation, or other features to help protect the operator's hand from electrical shock and burns. Test probes are rated according to the amount of voltage, current, temperature, or other input they can measure. When choosing a test probe, the maximum amount of input that the probe can measure should match or exceed both the maximum amount that can be tested by the test equipment, as well as that of the property expected to be present in the application.Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger, Biddle, States, and AVO. The company, founded in 1889, is headquartered in Dover, England, and meets International Organization for St...

Manufacturer: Megger Brand: Megger Model: 6111-022

The Megger 6111 series duplex test lead with helical spring-point duplex hand spikes is for use with Megger DLRO10HD, DLRO10, DLRO10X, and BT51 digital microhmmeters. This duplex test lead measures both current and resistance when taking four-wire resistance measurements, which are more accurate than two-wire resistance measurements and allow low resistance values to be detected. The helical spring-point hand spikes compress and rotate to make contact with a conductor. There is 0.4" (10 mm) between the current and potential probe tips on the duplex hand spikes.A test probe, test lead, test prod, or scope probe transmits an electrical signal to a testing device for display and analysis. Designs range from simple test leads with probe-style or clamp-on tips to more complex oscilloscope probes and current detectors. Some test probes, such as basic test leads, have wires with tips for connecting to test equipment. Other test probes, such as voltage detectors, are built into the meter. Depending on what is to be tested, the probe might either be passive or have active parts that require external power to operate. Some probes require contact for testing, while some are capable of taking measurements from a distance. Some also have finger barriers, insulation, or other features to help protect the operator's hand from electrical shock and burns. Test probes are rated according to the amount of voltage, current, temperature, or other input they can measure. When choosing a test probe, the maximum amount of input that the probe can measure should match or exceed both the maximum amount that can be tested by the test equipment, as well as that of the property expected to be present in the application.Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger, Biddle, States, and AVO. The company, founded in 1889, is headquartered in Dover, England, and meets International Organization for St...

Manufacturer: IDI Brand: D.I.D.

Contact Probes HEADED .035 60 DEG CHISEL STEEL

Manufacturer: JinHan Brand: Jinhan

The JinHan JDS3022A is a handheld electrical test device that combines a 30 MHz, Double-channel, handheld digital oscilloscope for viewing electrical signals with a manual- and auto-ranging digital multimeter for measuring AC voltage to 750V and DC voltage to 1000V, AC and DC current to 10 amp, resistance to 60 MΩ, and capacitance to 4000 μF. The oscilloscope has maximum real-time sample rate of 250MS/s and a record length of 6,000 points for acquiring detailed waveforms. Its 18 automatic measurements such as period, frequency, and peak-to-peak enable an in-depth analysis of waveforms. Up to four waveforms can be stored in the internal memory. The multimeter has two ranging modes: manual, which allows the user to select the operating range, and auto, which automatically selects the appropriate operating range. The delta relative function allows a measurement to be set as a reference value and displays subsequent measurements as a positive or negative deviation from that value, and the data-hold function freezes a reading on the display to aid documentation. A continuity buzzer confirms that the circuit conducts electricity, and a diode check detects whether a circuit's diodes are working properly. Additional specifications include various triggering features. The unit has a 4.3" color TFT (thin film transistor) LCD with a resolution of 400 x 272 pixels for viewing waveforms and measurements. An oscilloscope is used for electronics applications such as product design, assembly lines, repair and servicing, and electrical engineering education, among others. A multimeter is an electrical testing tool for measuring multiple properties of an electrical circuit to verify proper operation or diagnose problems. The unit has a USB port for connecting to a PC, It is rated for CAT II installations to 400V, which covers energy-consuming equipment connected to a fixed installation, including household, office, and laboratory. It has European Conformity (CE) marking.

Manufacturer: AEMC Brand: AEMC Model: SL261

The model SL261 is designed for AC/DC current measurement capabilities using hall effect technology. It measures from a few mA to over 100A. The "screw driver" shape, with its narrow elongated prod, was chosen to permit probing in crowded cable bundles, or measuring in tight areas such as on circuit boards, motor controllers and automotive circuitry. The electronics and batteries are self - contained in the handles. It is an excellent companion to DMMs, recorders and loggers, oscilloscopes and waveform displaying instruments. Low phase shift also insures reliable power and power quality measurements. The model SL261 is designed for current measuring and displaying on oscilloscopes. AC + DC output signals proportional to the total current are provided for true RMS measurements. Low AC and DC measurements. 50mA to 120AAC/150ADC. Unique design for probing in crowded wiring in industrial and automotive environments. Hall effect sensor technology. Use with DMMs, voltmeters and other voltage measuring instruments. Double insulation, CE mark. 10A and 100A Nominal range. 100mA to 100A Measurement range. Voltage output transformation ratio. 10A-100mV/A, 100A-10mV/A Output signal. Overload: red LED indicates input greater than the selected range. DC to 100kHz (-3dB with current derating) Frequency range. 600Vrms Working/Common mode voltage. 6.5' coaxial cable output termination. Operating temperature: 32 degree to 122 degree F. Storage temperature: -22 degree to 176 degree F. 0.46" Jaw opening. Dimensions: 9-11/128" width by 1-53/128" height by 2-81/128" depth. Weight 11.6oz with battery.