Electrical Testing - Page 442

Manufacturer: Megger Brand: Megger Model: 242004-7

The Megger 242002 series duplex test lead with C-clamp is for use with Megger DLRO10HD, DLRO10, DLRO10X, 247000, 247001, 247002, 247100, 247101, and BT51 digital low-resistance ohmmeters. This duplex test lead measures both current and resistance when taking four-wire resistance measurements, which are more accurate than two-wire resistance measurements and allow low resistance values to be detected. The lead has a maximum test current input of 10 amp. The C-clamp provides a hands-free connection to a conductor and can accommodate conductors up to 2" (5 cm). The C-clamp directs the current through the clamp and screw and the potential through a four-point anvil that is insulated from the clamp.A test probe, test lead, test prod, or scope probe transmits an electrical signal to a testing device for display and analysis. Designs range from simple test leads with probe-style or clamp-on tips to more complex oscilloscope probes and current detectors. Some test probes, such as basic test leads, have wires with tips for connecting to test equipment. Other test probes, such as voltage detectors, are built into the meter. Depending on what is to be tested, the probe might either be passive or have active parts that require external power to operate. Some probes require contact for testing, while some are capable of taking measurements from a distance. Some also have finger barriers, insulation, or other features to help protect the operator's hand from electrical shock and burns. Test probes are rated according to the amount of voltage, current, temperature, or other input they can measure. When choosing a test probe, the maximum amount of input that the probe can measure should match or exceed both the maximum amount that can be tested by the test equipment, as well as that of the property expected to be present in the application.Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger...

Manufacturer: Dranetz Brand: Dranetz Model: PR150/SP2

All Current Probes listed here are compatible with Dranetz portable instruments: PowerXplorer, PowerGuide, PowerVisa, PowerGuia, Energy Platform, PP4300, 658 with CA4300 adapter; and Dranetz permanent instruments: Encore 61000 with 61MAC module, Signature System 5513. Adapters are available for use with other instrument configurations; contact us for details. Dranetz recommends only Dranetz-brand probes be used with Dranetz power quality equipment

Manufacturer: Fluke Corporation Brand: Fluke Model: I6000S FLEX-24

The i6000sflex is an AC current probe utilizing the Rogowski principle. It can be used to measure currents up to 6000A when used in conjunction with oscilloscopes, recorders or data loggers. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas. Current ranges: 60A/600A/6000A AC rms. Output sensitivity (AC coupled): 50 mV /5mV / 0.5mV per A. Load impedance: 100 k ohm minimum. Accuracy (at +25 degree C): +/-1 percent of range (45 - 65 Hz). Linearity (10 to 100 percent of range): +/-0.2 percent of reading. Noise: 8mV AC rms (60 A), 2 mV AC rms (600/6000A). Frequency range: 10 Hz to 50 kHz (- 3 dB). Phase error: < +/-1 degree (45 – 65Hz), +/-10 degree (at 20 kHz). Position sensitivity (with cable > 25mm from the coupling): +/-2 percent of range. External field (with cable > 200mm from the head): +/-1 percent of range. Power supply: 2 x AA MN 1500 LR6 alkaline 400 Hours, low battery indicator or dedicated ext power supply. Temperature coefficient: +/-0.08 percent of reading per degree C. Working voltage: 600 V AC rms or DC. Head cable diameter: 14.3mm. Cable length (head to electronics): 2 meters. Operating temperature range: -20 to +90 degree C (head), -20 to +85 degree C (electronics). Storage temperature range: -40 to +105 degree C (head), -20 to +85 degree C (electronics). Operating humidity: 15 to 85 percent (non condensing).

Manufacturer: Agilent Technologies Brand: Agilent Technologies

Agilent Eclipse Plus Ph-Hex,2.1x50mm,1.8u,600bar - BC

Manufacturer: Agilent Technologies Brand: Agilent Technologies

Agilent Hypersil ODS, 3um, 4.0 x 100mm cartridge - BC

Manufacturer: Fluke Corporation Brand: Fluke Model: 2650124

Fluke molded transit case for 1750 and 1760 3 Phase power quality recorder.

Manufacturer: Amprobe Brand: Amprobe Model: 4416119

The Amprobe CT-326-C current tracer is a circuit tracer for locating and tracing electrical wires, breakers, neutrals, and ground lines in industrial settings. Twelve sensitivity settings allow the tracer to identify shorts and ground faults on both electrified and non-electrified circuits. LED lights indicate the presence of wires and breakers. The unit traces live wires and circuit breakers from 9 to 300V AC and 9 to 300V DC. The tracer digitally filters out electrical noise for increased accuracy in industrial settings. The unit locates and traces live wires and breakers buried underground or hidden in walls up to 13 feet deep without interrupting power. The tracer is powered by one 9V battery (installed), which provides power for about 100 hours of testing. It is shielded, so it does not interfere with sensitive equipment. The CT-326-C is designed to trace energized and non-energized wires and circuit breakers by electricians and electrical contractors in industrial settings. Specifications Power supply: 9V battery (one, installed) AC voltage range: 9 to 300V DC voltage range: 9 to 300V Amprobe manufactures electrical testing equipment for commercial, industrial, and home use. The company was founded in 1948 and is headquartered in Everett, WA. What’s in the Box? CT-326-C Current Tracer Transmitter Receiver (1) Set connection cables Carrying case (2) 9V batteries Instructions

Manufacturer: Linkinstruments Brand: Link Instruments

As a logic analyzer the IO-3208A topping out at 200Msa/s, the IO-3208A records at a blistering rate of 6.4Gbs/s into its deep 256Kpt buffer. Event resolution of 5ns can easily be analyzed. But what makes it so special is the integrated 8 ch Pattern Generator. The Pattern Generator is capable of clocking data out at the same furious rate as the Logic Analyzer. Precise sample to sample Input to output switching means that the IO-3208A can inject and listen to data on your bus. For ASIC designers, the IO-3208A offers a low cost solution to ASIC validation. For FPGA designers, you will no longer need to allocate precious logic and routing resources to soft logic analyzers. Timing closure can be achieved with a smaller device, just think of the cost saving in that! For embedded designers, external peripheral functions can be simulated using the Pattern Generator, which will greatly optimize your design workflow. For designers that need mostly logic analysis and occasional pattern generation, the IO-3208A offers an attractive lower cost option. Max sample rate: 200 MSa/s (internal), 200 Mhz (external) Channels: 32 (Logic Analyzer) + 8 (Pattern Generator) Buffer size: 256 KPt/channel Package contents: IO-3208A main unit, 4 wire harnesses, 11 clips, USB cable, CD

Manufacturer: DENT Instruments Brand: DENT Instruments Model: TCA-5-HV-KIT

Dent Instruments RoCoil TCA-5 Trans conductance Amplifier High Voltage Kit makes it easy to use RoCoil flexible with power meters that have 5A current transformer inputs. Dent Instruments RoCoil TCA-5 translates the output signal from RoCoil CTs into a 5Amp AC current to make them compatible with a variety of power meters. This kit includes the required 200/500VAC High Voltage power supply.

Manufacturer: Megger Brand: Megger

Be sure to Login to transcat.com for preferred member pricing.