Electrical Testing - Page 48

Manufacturer: Fluke Corporation Brand: Fluke Model: PM9091/001

The set consists of three black cables with colored BNC male connectors (red, gray and black) for easy identification. Cable length is 1.5m. Maximum signal voltage: 300V rms. Maximum voltage to ground: 600V rms. CAT III per IEC 61010-031. BB120 Shielded banana to BNC adapter is required to adapt to ScopeMeter 120 series shielded banana jack inputs.

Manufacturer: B&K Precision Corporation Brand: B&K Precision Model: CP 3

Outputs 1 mV per Amp, operates on 2V range of any DMM. Measures to 400A DC or AC

Manufacturer: Fluke Brand: Fluke Model: FLUKE 15B+ Color: Orange

New Feature: Faster response Greater capacitance range: 0.01nF ~ 1000μF The more bright: Add white LED backlight Larger screen: Larger than the original 1.5 times Maximum Voltage between any Terminal and Earth Ground: 1000 V Display(LCD)..................................................4000 counts,updates 3/sec Battery Type...................................................2 AA,NEDA 15A, IEC LR6 Battery life.......................................................500 hours minimum(50 hours in LED Test mode without load. The hours with load depends on the type of LED under test) Temperatuer Operating.........................................................0 deg to 40 deg Storage.............................................................-30 deg to 60 deg Relative Humidity Operating Humidity.......................................Non-condensing≤90%at 10deg to 30deg;≤75% at 30deg to 40deg Operating Humidity,40MC Range..............≤80% at 10deg to 30deg;≤70% at 30deg to 40deg Altitude Operating.........................................................2000m Storage.............................................................12.000m Temperature Coefficient..............................0.1×(specified accuracy)/deg( 28deg) Fuse protection for current inputs............440 mA,1000 V Fast Fuse, Fluck specified part only. 11A,1000v Fast Fuse Size(H×W×L)...................................................183×91×49.5(mm) Weight..............................................................455g IP Rating..........................................................IP 40 Safety...............................................................IEC 61010-1, IEC61010-2-030 600V CAT Ⅲ,1000V CATⅡ，Pollution Degree 2 Electromagnetic Environment...................IEC 61326-1:Portable Electromagnetic Compatibility..................Applies to use in Korea only

Manufacturer: Signstek Brand: Signstek

Product Description: DSO201 Pro Nano V3 is an upgraded version 32bit digital storage oscilloscope. Based on ARM -M3, it's equipped with 320*240 color display, USB port and recharging function. It's compact, simple to operate; meets the basic demands of school lab, electric furniture repairmen and electric engineering. The version 3 of DSO Nano differs from version 2 in that it does not use white plastic shell. Instead, it uses black metal shell which is more durable and strong. Product Specification: Display: 2.8′ Color TFT LCD Display Resolution: 320×240 Display Color: 65K Analog bandwidth: 0 - 1MHz Max sample rate: 1Msps 12Bits Sample memory depth: 4096 Point Horizontal sensitivity: 1uS/Div～10S/Div (1-2-5 Step) Horizontal position: adjustable with indicator Vertical sensitivity: 10mV/Div～10V/Div (with ×1 probe); 0.5V/Div～10V/Div (with ×10 probe) Vertical position: Adjustable with indicator Input impedance: >500Kω Max input voltage: 80Vpp (by ×1 probe) Coupling: DC Trig modes: Auto, Norma, Single, None and Scan Test signal: Built-in 10Hz～1MHz (1-2-5 Step) Upgrade: By bootloader via USB Power supply: 3.7V Chargeable Lithium battery / U SB Dimension (w/o probe): 105mm X 53mm X 8mm PC connection: Mini USB B-Type Our Guarantee If you have any questions about the product you got, please feel free to contact with us at any time, we'll provide our best service to you and do our best to resolve the problem you met. Package 1 x DS0201 Digital Oscilloscope Device 1 x Probe (x1/x10) 1 x Mini USB Cable 1 x Flannel bag

Manufacturer: Extech Brand: Extech Model: MA260

The MA260 is a True RMS 200A AC Open Jaw Clamp Meter. The MA260 has a built in NCV detector and can measure up to 200A in its 0.6 in. open jaw. True RMS for accurate readings of noisy, distorted or non-sinusoidal waveforms. Complete with test leads and two AAA batteries. UL listed with a CAT IV 600V safety rating.

Manufacturer: TKDMR Brand: LONGH Color: White

LED LCD TV screen backlight problems are getting increasingly common. As we know, slight voltage change can have a big influence on TV function. When LED TVs come backlight failure,what should you do? So you need a useful tool which is called LED Lamp LED TV Backlight Tester. This LED Lamp LED TV Backlight Tester can find defective LED on the strip in few seconds because of automatically adjust the voltage level and current. This LED tester can save your time to find the TV which back light is defective.It is really a good tool for Every Technician. If there is something wrong with LED strip, you can change it or replace the bad LED beads. Applicable to any size LED TV , perfect backlight inspection and maintenance tool !  Input Voltage: 85-265V  Output Voltage: 0-300V  Main Application: - Suitable for single LED beads, LED stirng, LED panel and Integrated optical LED - Support testing the capacitance voltage and the diode voltage - No need to disassemble panel to test the LED stripswhich can save a lot of time for you. - Safe Protection: Double Isolated  - Burn protection: Voltage and Current Intelligent Adjustment  - Safety design : Slow boost , soft start. Increase the current steadily.  How to operate this LED Lamp LED TV Backlight Tester? 1. Plug in power, it would be cost about 3 to 5 seconds to start 2. The soft start mode make the backlight getting brighter gradually 3. If you can't make sure which is"+"and "-", then not test for a long time 4. Don't touch the output terminal of probes for a long time  5. Retardancy materials: Double Isolate Design makes tester safety with high strength and flame 

Manufacturer: Armada Technologies LLC Brand: Armada Technologies

The Armada Technologies Pro48 TechTool Sprinkler Solenoid and Clock Checker is a new low cost test set for irrigation contractors and maintenance personnel. The Armada Tech Pro48 performs a series of simple procedures to test, verify, and identify solenoid, wire, and clock problems. Sprinkler solenoids can be checked using either activation or chatter modes. Lost or buried solenoids are quickly found as well by listening for the chatter.Wiring can be verified and tagged with the built in tone generator function. Clocks also are tested for proper 24v transmission with a simple LED power check. Made from a grommeted, thick walled plastic case, the highly visible yellow Armada Technologies Pro48 TechTool Sprinkler Solenoid Activator is designed for rugged use in the field.

Manufacturer: Greenlee Brand: Greenlee Model: CSJ-100 Color: NA

Greenlee CSJ-100 Specifications: Amperage measurement: 200.0 AC Voltage measurement range: 200.0, 1000V Resistance: 200.0 Ohms; 2.000, 20.00, 200.0 kOhms; 2.000, 20.00 MOhms Display: 2000 count LCD Jaw opening: 0.63" (16mm) Measurement Category: Cat IV 600V, Cat III 1000VGreenlee CSJ-100 Includes: (2) 1.5V AAA batteries Test leads Carrying caseGreenlee CSJ-100 Features: AC amperage, AC/DC voltage measurement. Open jaw design eases AC current measurement. Slim profile with built-in probe storage on back. Measures resistance up to 20MOhms. Audible continuity and diode test. Bright LED and audible alarm for non-contact voltage detection. Auto power off for longer battery life. Data hold to capture measurements. 2000 count LCD. Replacement test leads also available separately (Greenlee 11372)

Manufacturer: EKM Metering Inc. Brand: EKM Metering Inc. Model: EKM-25IDS

Voltage: 120/240 volts 3-Wire Amperage: up to 100 amps Type: Pass-Through, Single-Phase, 60Hz Data: Pulse Output - 800 pulses per kWh Model: EKM-25IDS This is a very popular product if you are metering your North American household power and you want a simple read-off-the-face kWh meter. State-of-the-art, fully solid-state kWh meter with 800 pulse per kWh pulse output 1% accuracy class, LCD readout in hundredths of a kWh, to 99999.99 kWh. No conversion factor or multiplier. Basic single phase 120/240V 3-wire, 100A version, Neutral bypasses the meter. PLEASE NOTE: No external current transformers are needed with this meter. The CTs are inside the meter already. Wires pass through the body of the meter and through the internal current transformers. Do NOT buy additional current transformers with this meter, even if Amazon says that they are frequently bought together. Compact, very easy to install design. Simple DIN-rail mounting. Wires pass through 3/8+" diameter tubes in the meter body--Will accept #3AWG insulated wire. The only electrical connection is made by 2 small screws which penetrate the wire insulation and pick up power--less than 1 watt--to power the meter. Non-resettable LCD display. Usage data is maintained through power outages. Single-phase energy meter, 100A 120/240-volt, 3-wire, 60Hz. Standard North American household current. Most commonly a white neutral, a black hot and a red hot wire, 200V to 252V between the hots, 110V to 126V either hot to neutral. Very voltage tolerant--the meters will tolerate voltages from 168 V to 312V hot to hot, 84V to 156V hot to neutral. *This meter will not work on a single phase 120v 2-wire system. For that application please see our EKM-15IDS.

Manufacturer: EKM Metering Inc Brand: EKM Metering Inc. Model: EKM-15IDS

Voltage: 120 volts Amperage: up to 50 amps Type: Pass-Through, Single-Phase, 60Hz Data: Pulse Output - 800 pulses per kWh Model: EKM-15IDS Our EKM-15IDS is a revenue grade kWh submeter. It is great for metering any 120 volt load to a high accuracy required for billing purposes or just for tracking usage. This meter provides an excellent value if you are looking for a simple, read-off-the-face meter. Very reliable and easy to install. This is the 120 volt version of our EKM-25IDS which is a 120/240 volt 3-wire meter. State-of-the-art, fully solid-state kWh meter with 800 pulses per kWh pulse output Accurate to within 1%, LCD readout in hundredths of a kWh, to 99999.99 kWh. No conversion factor or multiplier needed. Compact, very easy to install design. Simple DIN-rail mounts. Wires pass through 3/8+" diameter tubes in the meter body--Will accept some (but not all) #2AWG insulated wire. The only electrical connection is made by 2 small screws which penetrate the wire insulation and pick up power for the meter and give the meter it's voltage reference. This meter draws less than 1 watt. Non-resettable LCD display. Usage data is stored even if the meter loses power for 10 years. Tamper-proof and meter sealable. Single-phase energy meter, 50A 120-volt 2-wire 60Hz Most commonly a white neutral and a black or red hot wire, 110V to 126V between them. Very voltage tolerant--the meters will tolerate voltages from 84V to 156V!! Perfect for knowing how much power your apartment, office, RV park, industrial space, or any other device that uses 120 volt electricity.