Electrical Testing - Page 779

Manufacturer: Hantek Brand: Hantek HDG2032B

We need about 4 business days to prepare it for you and will send it to you by FedEx, UPS or DHL service. Specifications: Main Features *Model:HDG2032B *Channel:2 *Waveform Length:64M *Bandwidth:30MHz *Frequency:1μHz-30MHz *Sample Rate:250MSa/s *Voltage Resolution:16Bit *Digital Output Mode:16 Channels Frequency Characteristics *Waveform:Sine,Square,Ramp,Pulse,Noise,Sinc,Exponential Fall,ECG,Gauss,Haver Sine, Lorentz,Dual-Tone,DC *Sine:1μHz-30MHz *Square: 1μHz-25MHz *Pulse: 1μHz-20MHz *Ramp: 1μHz-2MHz *White Noise:30Mhz *Harmonic/Arbitray: 1μHz-20MHz *Resolution: 1μHz *Accuracy:±2ppm,18℃-28℃ Square *Rise/Fall time(Typical):＜14ns *Overshoot:Typical Value(100KHz,1Vpp)＜3% *Duty Cycel:≤10MHz:20.0%-80.0%;10MHz-40MHz:40.0%-60.0%;＞40MH:50.0%(fixed) *Non-symmetry:1% of period+5ns Ramp *Linearity:≤1%(Typical,1kHz,1VPP,Symmetry 100%) *Symmetry:0%-100% Pulse *Period:200ns-1millons *Pulse:≥16ns *Leading/Trailing Edge Time: ≥10ns *Overshoot:Typical (1Vpp)＜3% Amplitude Characteristic *Amplitude Range:≤20MHz:1mVpp-20Vpp; ≤60MHz:1mVpp-15Vpp; ≤80MHz:1mVpp-10Vpp ;≤90MHz:1mVpp-5Vpp; ≤10MHz:1mVpp-2Vpp *Resolution:1mv or 4 digits *Isolation:＜-80dB *Impedance:50Ω(Typical) 7.Modulation Characteristic:Support AM,FM,PM,ASK,FSK,PSK and PWM modulations 8.Burst Characteristic *Burst Count:200000000 *Gated Source:External Trigger *Trigger Source:Internal External or Manual 9.Sweep Characteristic *Direction:Up *Type:Linear *Sweep/Hold/Return Time:280000s

Manufacturer: B&K Precision Corporation Brand: B&K Precision Model: 4045B

Models are versatile sweep function generators utilizing an advanced direct digital synthesis (DDS) design. These instruments generate sine, square, and triangle waveforms with high signal precision and stability. Both models provide variable output voltages from 0 to 10 Vpp into 50 ohms or up to 20 Vpp into open circuit, and a continuously variable DC offset to inject signals directly into circuits at the correct bias level.

Manufacturer: AEMC Brand: AEMC Model: 1045

The AEMC 1045 digital megohmmeter is an auto-ranging insulation tester with a voltage safety check and three test voltages—250, 500, and 1,000V—for measuring insulation resistance to 2,000MΩ to indicate the condition of windings or cables in motors, switchgears, electrical installations, and other insulated equipment, and it also measures low-resistance to 400kΩ and AC and DC voltage to 600V, disabling insulation testing when a voltage greater than 25V is detected. The timer mode enables timed insulation resistance measurements, sounding a buzzer at appropriate intervals so the user can calculate the PI (polarization index) and DAR (dielectric absorption rate) which give a truer indication of insulation condition than single-point measurements. High and low thresholds for insulation and resistance measurements can be set, triggering an alarm when readings fall outside the settings, and will be retained even after the meter is powered off. When measurement is complete, the meter enters voltage detection mode and automatically discharges residual voltage from the circuit under test. The meter can perform a continuity check up to 20Ω and buzzes to confirm that a circuit conducts electricity. It has a 4,000-count LCD with a backlight for visibility in low light that automatically turns off after one minute. The display shows readings numerically and on a 34-segment bar graph. This auto-ranging meter automatically selects the appropriate operating range for measurements. It is rated for category (CAT) II installations to 300V, which covers energy-consuming equipment connected to a fixed installation, including household, office, and laboratory appliances. The unit automatically turns off after five minutes of non-use to conserve battery life and has a low-battery indicator that signals when the batteries need to be replaced. It comes with a set of test leads, a set of alligator clips, a test probe, six 1.5V AA batteries, a soft carrying case, and instructions. Megohmmeters are commonly used for ...

Manufacturer: FLUKE Brand: Materro(tm)

FLUKE 1503 DIGITAL INSULATION TESTER 1000V 2000MOHM

Manufacturer: Rigol Brand: Rigol Model: DG1011

Manufacturer: Agilent Technologies Brand: Agilent Technologies

Agilent Eclipse Plus Ph-Hex,3x50mm,1.8u,600bar - BC

Manufacturer: REED Instruments Brand: Reed Instruments Model: R9900-NIST

The REED R9900 Indoor Air Quality Meter measures carbon dioxide levels, air, dew point and wet bulb temperatures, as well as humidity levels; all critical factors in diagnosing air quality within and around buildings and structures. Thermal comfort can be achieved only when air temperature, humidity and air movement are within a specified range. The REED R9900 Indoor Air Quality Meter can be an economical choice in maintaining constant thermal conditions that are crucial both for one's well-being and for productivity.

Manufacturer: Veris Brand: Veris

Bi-Directional Power and Energy Meter, Data Logging: 10 16 Bit Configurable Data Buffers, 60 Day Readings (15-min Intervals), Alarm Output (N.C.), 1 Pulse Output (N.O.), RS-485 Serial Modbus RTU Protocol, 5-Year Warranty

Manufacturer: Schneider Brand: Schneider Model: A9MEM3555

Energ Meter, iEM3555 3PH, Rogowski coil, Cls 0.5S, Modbus, 4-quad, (1)DI, (1)DO

Manufacturer: Megger Brand: Megger Model: 6320-245

The Megger 6320-245 professional ground test kit is a kit of accessories for conducting ground resistance tests with a Megger DET3 or DET4 ground resistance tester (sold separately). The kit includes 50m (164’) red and black cable reels, 30m (98’) yellow and green cable reels, 4m (13’) earth electrode leads, a 4mm shrouded plug and large croc clip, 4 auger-style spikes, fiberglass measuring tape, and a molded plastic carrying case that holds all of the accessories. The 6320-245 is an accessory for use with Megger DET3 and DET4 series ground resistance testers.Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger, Biddle, States, and AVO. The company, founded in 1889, is headquartered in Dover, England, and meets International Organization for Standardization (ISO) 9001:2008 standards.