Electrical Testing - Page 827

Manufacturer: Megger Brand: Megger Model: 241005-7

The Megger 241005-7 series duplex test lead with gold-plated Kelvin clip is for use with Megger DLRO10HD, DLRO10, DLRO10X, 247000, 247001, 247002, 247100, 247101, and BT51 digital low-resistance ohmmeters. This 7' (2 m) long duplex test lead measure both current and resistance when taking four-wire resistance measurements, which are more accurate than two-wire resistance measurements and allow low resistance values to be detected. The lead has a maximum test current input of 10 amp. The gold-plated Kelvin clip provides low contact resistance and has better resistance to corrosion and wear than a silver plated clip. The Kelvin clip directs current through one jaw and potential through other jaw when taking resistance measurements on cables and small wires. It has a jaw opening of 0.5" (1.3 cm).A test probe, test lead, test prod, or scope probe transmits an electrical signal to a testing device for display and analysis. Designs range from simple test leads with probe-style or clamp-on tips to more complex oscilloscope probes and current detectors. Some test probes, such as basic test leads, have wires with tips for connecting to test equipment. Other test probes, such as voltage detectors, are built into the meter. Depending on what is to be tested, the probe might either be passive or have active parts that require external power to operate. Some probes require contact for testing, while some are capable of taking measurements from a distance. Some also have finger barriers, insulation, or other features to help protect the operator's hand from electrical shock and burns. Test probes are rated according to the amount of voltage, current, temperature, or other input they can measure. When choosing a test probe, the maximum amount of input that the probe can measure should match or exceed both the maximum amount that can be tested by the test equipment, as well as that of the property expected to be present in the application.Megger manufactures equipment for cable fault locating, protective relay testing, telecommu...

Manufacturer: Megger Brand: Megger Model: 242011-30

The Megger 242011 series duplex test lead with helical spring-point duplex hand spikes is for use with Megger 247100, 247101, DLRO10HD, DLRO10, and DLRO10X digital low-resistance ohmmeters. This duplex test lead measures both current and resistance when taking four-wire resistance measurements, which are more accurate than two-wire resistance measurements and allow low resistance values to be detected. The lead has a maximum test current input of 10 amp. The helical spring-point hand spikes compress and rotate to make contact with a conductor. There is 0.4" (10 mm) between the current and potential probe tips on the duplex hand spikes.A test probe, test lead, test prod, or scope probe transmits an electrical signal to a testing device for display and analysis. Designs range from simple test leads with probe-style or clamp-on tips to more complex oscilloscope probes and current detectors. Some test probes, such as basic test leads, have wires with tips for connecting to test equipment. Other test probes, such as voltage detectors, are built into the meter. Depending on what is to be tested, the probe might either be passive or have active parts that require external power to operate. Some probes require contact for testing, while some are capable of taking measurements from a distance. Some also have finger barriers, insulation, or other features to help protect the operator's hand from electrical shock and burns. Test probes are rated according to the amount of voltage, current, temperature, or other input they can measure. When choosing a test probe, the maximum amount of input that the probe can measure should match or exceed both the maximum amount that can be tested by the test equipment, as well as that of the property expected to be present in the application.Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger, Biddle, States, and AVO. The company, founded in 1889, is ...

Manufacturer: Rohde & Schwarz Brand: Rohde & Schwarz Model: 3593.0980.02

The HMC8012 provides a diverse choice of easily accessible measurement and mathematical functions. Multimeter is able to simultaneously display up to three measurements that are now even easier to read from a crisp color TFT display. Considering the compact size of HMC8012, it will fit perfectly both on a bench and on a shelf. Other specifications: Measurement range: DC to 100 kHz. Resolution: 1 μV, 100 nA, 1 mΩ, 1 pF, 1 Hz, 0.1 °C/F. Measurement rate: up to 200 values/s. Measurement functions: V (DC), I (DC), V (AC), I (AC), frequency, DC power, resistance (two and four-wire), temperature (PT100/PT500/PT1000), capacitance, diode and continuity test.

Manufacturer: Fluke Corporation Brand: Fluke Model: 65157MM-AMZN

The Fluke 1587 mdt advanced insulation and motor drive troubleshooting Kit is designed for troubleshooting and preventive maintenance applications including three-phase motors, cables, switch gear, and in applications where testing is required without the need to break the circuit. The Kit includes the Fluke 1587 Digital insulation Multimeter, Fluke I400 current clamp, and Fluke 9040 phase rotation indicator.

Manufacturer: AEMC Brand: AEMC

The Ground Resistance Tester Model 6417 measures ground rod and grid resistance and impedance without the use of auxiliary rods. Clamp-on ground resistance testers can be used in multi-grounded systems without disconnecting or de-energizing the ground system under test it. The Model 6417 simply clamps around the grounding electrode or conductor and measures the resistance to ground. By performing measurements on intact ground systems, the user also verifies the quality of the grounding connections and bonds. Resistance and continuity of grounding loops around pads and buildings may also be measured. Three new features unique to AEMC® are: Test frequency selection provides more accurate results in inductive environments Touch voltage indication  indicates the voltage on the display along with a warning buzzer when the voltage derived from current and resistance measurements detect a potentially dangerous touch condition Loop resistance indication alerts the user to the fact that the measurement may not be ground resistance The Ground Resistance Tester Models 6416 and 6417, measure ground rod and grid resistance without the use of auxiliary rods. Clamp-on ground resistance testers can be used in multi-grounded systems without disconnecting the ground system under test or de-energizing them. The Models 6416 and 6417 simply clamp around the ground conductor or rod and measure the resistance to ground. By performing measurements on intact ground systems, the user also verifies the quality of the grounding connections and bonds. Resistance and continuity of grounding loops around pads and buildings may also be measured. Two new features unique to AEMC ® are test frequency selection and touch voltage indication. The ability to select the test frequency provides more accurate results in inductive environments

Manufacturer: Hioki Brand: Hioki

Hioki 3511-50 LCR Hi-Tester (120Hz and 1kHz)   LCR Hi-Tester × Compact, lightweight single-function model High-speed measurement Comparator function LED display Two interfaces The Hioki 3511-50 LCR HiTESTER features both high performance and high speed measurements with a low price. The minimum measurement time of 5 ms and a basic accuracy of ±0.08% makes the instrument suitable for use on production lines and laboratories. The built-in high speed comparator significantly reduces production line tact time and allows the construction of automatic production lines. The compact body features a clearly visible LED display that facilitates easy operation and allows settings to be confirmed at a glance The PW3360 Clamp on Power Logger is a clamp-type power meter capable of mea- suring lines with from single-phase to three-phase four-wire. The instrument can perform basic measurements including voltage, current, power, power factor, and energy. Hioki LCR Meters and Impedance Analyzers range from 1mHz to 1.3GHz devices to suit a wide range of applications in the testing of electronic components. The 3511-50 is a compact, general purpose LCR meter for on-board testing of capacitors and coils used in electrical equipment and devices such as automotive-related components.   Front View Front View × Measurement display Displays a testing parameter and corresponding measurement. Status display Displays current test conditions, presettings, and other information. Comparator judgment display Displays judgment in comparator mode

Manufacturer: Fluke Corporation Brand: Fluke Model: EI-162BN

The Fluke EI-162BN split core clamp-on transformer allows the Fluke 1623 or Fluke 1625 earth ground tester to take ground loop resistance measurements around transmission line pylons. The split core transformer makes it possible to measure individual resistances for each tower leg without disconnecting ground leads, overhead static wires, or ground wires. The transformer has 1,000 windings, with connections at winding ratios of 1,000, 500, 300, 200, and 0 available to set before use with meter for minimum measuring and maximum parasitic currents expected to flow through the transmission line pylon. The inside diameter of the clamp is 320mm/12.6 inches. The split core transformer includes two fasteners for holding the transformer halves together, a cable bobbin with two 12m/40ft. test leads for connecting the transformer to the tester’s jack, contact clamp, user manual, and a carrying case. If the user owns the non-kit version of the Fluke 1623 or 1625 ground resistance meter, the split core transformer also requires use of a Fluke 2539195 probe cable (sold separately). The Fluke E1-162BN is manufactured in compliance with DIN ISO 9001 quality assurance system. Specifications Transformation ratios 1:1000, 1:800, 1:500, 1:300, and 1:200 Temperature range -10 degrees to 50 degrees C/14 degrees to 122 degrees F Weight 4.9kg/11lb. Dimensions 377mm/15 inches outside diameter, 310mm/12 inches inside diameter, 30mm/1.25 inches depthGround-resistance meters test the condition of a grounding system, and provide resistivity measurements in ohms. The meters are available in digital, analog, and clamp models. Grounding systems protect people and equipment, and provide a safe path for the dissipation of fault currents, lightning strikes, static discharges, EMI and RFI signals, and interference. Regular testing of a grounding system is important for safety and protection of equipment. For example, corrosive soil with high moisture content can degrade ground rods and connections in existing systems and increas...

Manufacturer: Megger Brand: Megger Model: 6410-919

The Megger BM15 5kv insulation resistance tester measures insulation resistance and voltage in electrical installations, building maintenance, and telecom systems. This analog meter has manual test voltage selection for flexibility of use. The unit has four test voltage options at 500, 1,000, 2,500, and 5,000V. The unit measures insulation resistance from 100 kilohms to 20 gigaohms and voltage from 0 to 600V alternating current (AC). The tester is safety rated to European Standard EN61010-1, Category III, 300V and Category I, 600V. The Megger BM15 is commonly used by electricians, electrical contractors, and telecommunications workers.Specifications Power supply 8 AA batteries Voltage testing range 0 to 600V AC Test voltages 500, 1,000, 2,500, and 5,000V Insulation resistance range 100 kilohms to 20 gigaohms Weight 1.2kg / 2.6 lb. Safety standard met International Electrotechnical Commission (IEC)/European Standards (EN) 61010-1 Cat III 300V, Cat I 600V Dimensions 220 x 160 x 115mm / 8.9 x 6.3 x 4.5 inchesH is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Electrical test meters display information either in analog form using a needle that moves on a calibrated scale, or in digital form using digits or a graphic representation on an LED screen. Meters have electrical properties that are to be measured and the anticipated range of results, and should have a rating that is higher than the maximum value of t...

Manufacturer: BCX Utra Brand: BCX ULTRA Model: BT-HFPCM2 Color: Black

Double Bubble Tube that connects to BCX Ultra. The number one reason people use this device is that they are hands free and is perfect for use while sleeping or running on multiple people. This device runs all of our built in prestored programs, sweeping programs and Rife's original frequencies since it runs the full range of BCX Ultra frequencies and carrier wave. Another reason is because of it is power, 150 watts!

Manufacturer: Megger Brand: Megger Model: 6410-979

The Megger BT51/120 digital microhmmeter measures resistance in un-energized lines in substation equipment, transmission lines, bond testing, domestic and industrial wiring, and other electrical systems. This digital meter has manual range selectioin for flexibility of use. The unit is designed for 120V operation. The 2A test current is used on two different ranges. The 0 to 2,000 milliohm range has a resolution of 1 milliohm, while the 0 to 20 milliohm range has a resolution of 0.01 milliohm for greater accuracy. The unit is safety rated to International Electrotechnical Commission standard IEC61010-1. The BT51/120 is used by electricians and electrical contractors.Specifications Power supply 4Ah capacity NiCad rechargeable battery with internal charging Resistance range 0 to 2,000 milliohms Test current 2A Weight (including batteries) 45kg/10 lb. Safety standard met International Electrotechnical Commission (IEC) 61010-1 Dimensions 245 x 344 x 158mm/9.6 x 13.5 x 6.25 inches (H x W x D)H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Electrical test meters report electrical circuit properties, such as voltage, resistance, capacitance, and continuity. Available in handheld or benchtop form, they detect electrical problems in equipment, wiring, and power supplies. A variety of probes, clamps, and leads can be used to connect the meter to a circuit or device. Single-function meters, such as battery testers and voltage testers, measure one property of a circuit, and multimeters measure multiple properties. Electrical test meters display information either in analog form using a needle that moves on a calibrated scale, or in digital form on an LED screen. Meters have electrical properties that are to be measured and the anticipated range of results, and should have a rating that is higher than the maximum value of the anticipated range. Meters measure electrical properties and...