Thermal Imagers - Page 7

Manufacturer: HT Instruments Brand: HT Instruments Model: T2000

HT Instruments T2000 Earth Ground Clamp Meter The T2000 model is designed for the resistance measurement on earth probes with ground loop method without the disconnection of parts of plants under test. This type of measurement carried out by the instrument can be used for evaluation of single rods' resistances within an earth installation assuming they do not affect each other. The inner part of the instrument is made of 2 jaws one for current and one for voltage. The voltage jaw generates a potential (E) on the loop during resistance measurement. A current (I) is consequently generated on the loop and is measured by the current jaw. Based on the value of parameters E and I the instrument displays the resistance value R calculated as their ratio. The T2000 also performs AC current up to 20A and leakage current with 0.05mA resolution and the setting of alarm thresholds on measurements is possible. The instrument is in compliance with IEC/EN61010-1, CAT III 150V and is ideal to carry out easily measurements both in domestic and industrial environments.

Manufacturer: Fluke Brand: Fluke

.da-ilf-gsep{ background-color: #ffc70a; } .da-ilf-gsep h3{ color: #f6f7e5 !important; }

Manufacturer: Fluke Brand: Fluke Model: 5609-20-G

Fluke 5609-20-G Probe, Secondary PRT, 100 OHM (1/4 X 20 INCH). If you want a very stable thermometer from -200 °C to 670 °C and are particular about the calibration, then look no further than our 5609 Secondary Reference PRT. Its short-term stability at the triple point of water is only ± 7 mK and its one-quarter inch (6.23mm) diameter lets you get accurate measurements in only 100 mm of immersion. The 5608 is also a ± 7 mK probe at the triple point of water, but its one-eighth inch (3.18 mm) diameter gets you accurate measurements from -200 °C to 500 °C with only 80mm (3.1 in) of immersion. With multiple sheath length options on both of these probes, you can find the dimensions that are just right for your specific application. The 5608 comes with a one-eighth inch (3.18 mm) diameter sheath in lengths of 9 inches or 12 inches. The 5609 comes with a one-quarter inch (6.35 mm) diameter sheath in lengths of 12 inches, 15 inches, and 20 inches; or with a 6 mm diameter in lengths of 300 mm, 400 mm, or 500 mm. When looking for improved response time and reduced stem effect in shallow immersion, look for small diameter probes, because the measurement error called stem effect is caused by the diameter of the stem rather than the length of the stem. Both of these probes have InconelTM sheaths and are made using a special manufacturing process, giving them great precision over a wide temperature range. The sensors for these probes are reference-grade platinum and feature four-wire connections with less noisy measurements than two-wire counterparts. These probes come with a certificate of compliance to ensure the meet their specifications. If you'd like, you can also order a NVLAP-accredited calibration from our laboratory, lab code 200348-0. On the report of calibration, you'll get the test data and the ITS90 calibration coefficients that you can easily input into any Fluke Calibration thermometer

Manufacturer: CEM Brand: CEM Model: DT-980

Thermal cameras are designed to enhance the electrical, mechanical and building diagnostics of users across key industries and professions. The DT-980 model has the following features: *2% accuracy with temperature range from -20°C to +150°C (-4°F to 302°F) *Display 2.8" LCD, 240 x 320; *Swappable Li-ion Battery with 4 hour life *2% accuracy *8GB storage SD *JPG storage format *Onboard digital camera 5MB

Manufacturer: Fluke Brand: Fluke Model: 5618B-6-S

With each probe you will receive a full NVLAP-accredited calibration report. On the report you'll get the test data and the ITS-90 calibration coefficients that you can easily input into your Fluke Calibration thermometer. The 5618B is also a great probe to use for calibrating your Fluke Calibration 9132 or 9133 infrared calibrators. In fact, these IR black body heat sources were designed to be calibrated with this type of probe. Now you can calibrate these targets in your own lab! For use from -200 °C to 500 °C (the six-inch model goes to 300 °C), you won't find a better industrial standard in this configuration than our 5618B. We recommend using the 5618B PRTs with the 1523, 1524, 1502A, 1529, or 1560 thermometer readouts.

Manufacturer: Iris Brand: IRIS USA, Inc.

.da-ilf-gsep{ background-color: #000000; } .da-ilf-gsep h3{ color: #5798c9 !important; }

Manufacturer: HT Instruments Brand: HT Instruments

Insulation Resistance, Ground Resistance & Bonding Continuity New Icon Menu Easy to use and to connect Innovative Design       One instrument for all electrical safety tests according to IEC/EN61557-1. Earth resistance with 2- or 3-pole volt-ampere method in TT, TN and IT systems, non-trip earth loop impedance measurement. Measurement of electrical parameters in single phase installations (V, A ,W,VAR,VA, PF) Continuity measurement of protective conductors. Soil resistivity. Insulation resistance measurement. Stackless earth ground resistance measurement with T2100 (optional).   MACROTESTG2 EARTH GROUND | INSULATION | CONTINUITY | POWER QUALITY   MACROTEST G2 is an innovative multifunction installation tester capable of carrying out safety tests on civil and industrial electric systems in compliance with IEC/EN61557-1. Its resistive TFT color touch-screen display, its icon menu, its help-on-line and its user-friendly development make the instrument extremely intuitive even for unskilled users. Its numberless features grant the user a wide range of applications in the world of measurements. The multifunction installation tester MACROTEST G2 allows saving all measures into an internal memory so transferring the saved data to a PC by means of USB (provided as standard) or built in Wi-Fi interfaces with an iOS and Android smartphones or tablets .The software supplied among standard accessories allows printing testing reports.The multifunction installation tester MACROTESTG3 has as Optional clamp T2100 permits to quickly check the resistance of earth probes without disconnection from earth system

Manufacturer: Fluke Brand: Fluke

Fluke 750P5IN Pressure Module, 0 to 5 Inch H2O (0 TO 12.5 MBAR). The 750P5IN Pressure Modules are easy to use. To measure pressure, connect the pressure module to a pressure source or hand pump and then connect the pressure module cable to the calibrator. Apply pressure from the pressure source and it is displayed digitally on the calibrator. At the touch of a button, the pressure may be displayed in up to 11 different engineering units. The Fluke 750P5IN Differential Pressure Module is part of a family of pressure models designed for the 750 and 740 series Documenting Process Calibrators and the 720 and 710 series Multifunction Process Calibrators. Differential pressure modules have two pressure fittings and measure the difference between the applied pressure on the high fitting versus the low fitting.

Manufacturer: Fluke Brand: Fluke

Silicone Oil Fluid, 200.20, 5 Gallon.

Manufacturer: NETCNA Brand: NETCNA

The OTS-HD 384 1.25-5x19 Thermal Digital Monocular from ATN features gyroscopic image stabilization that keeps the image steady at higher power. The OTS-HD can capture 1280 x 960 still images or video at 30 fps and saves them to an on-board microSD card slot. A micro-HDMI output lets you display the captured photos or video to a computer or TV for playback and storage. An easier way to share images is to use the built-in Wi-Fi. It features a Smart Range Finder, with only two clicks and a simple shift of the scope you will be able to range your target. Once ranged in your reticle, it will automatically adjust its point of impact. Connect the monocular to any device running the free Obsidian app and stream the current view, save images to the device, and instantly post them on social media, message them, or email them to friends and family. A built-in GPS antenna enables geo-tagging your photos or video so you can map where every image was taken. The GPS system will also log your altitude and speed so you'll know if you'll make your next waypoint on-time or if you need to pick up your pace.