|
|
-
4.9 of 5.0 with 2 Reviews
SALE PRICE: $995.00
Manufacturer: HT Instruments
Brand: HT Instruments
Manufacturer: HT Instruments
Brand: HT Instruments
|
HT Instruments T2100 Earth Ground Clamp Meter with RS23 The T2100 model is designed for the resistance measurement on earth probes with ground loop method without the disconnection of parts of plants under test. This type of measurement carried out by the instrument can be used for evaluation of single rods' resistances within an earth installation assuming they do not affect each other. The inner part of the instrument is made of 2 jaws one for current and one for voltage. The voltage jaw generates a potential (E) on the loop during resistance measurement. A current (I) is consequently generated on the loop and is measured by the current jaw. Based on the value of parameters E and I the instrument displays the resistance value R calculated as their ratio. The T2100 is equipped with a half-duplex RS-232 interface to operate with MACROTESTG3 instrument. The instrument is in compliance with IEC/EN61010-1, CAT III 150V and is ideal to carry out easily measurements both in domestic and industrial environments.
-
4.9 of 5.0 with 8 Reviews
SALE PRICE: $1,135.00
Manufacturer: Fluke
Brand: Fluke
Model: 5609-9BND-G
Manufacturer: Fluke
Brand: Fluke
Model: 5609-9BND-G
|
Fluke 5609-9BND-G Probe, Secondary PRT, 100 OHM, 9IN 90 DEG BEND. If you want a very stable thermometer from -200 °C to 670 °C and are particular about the calibration, then look no further than our 5609 Secondary Reference PRT. Its short-term stability at the triple point of water is only ± 7 mK and its one-quarter inch (6.23mm) diameter lets you get accurate measurements in only 100 mm of immersion. The 5608 is also a ± 7 mK probe at the triple point of water, but its one-eighth inch (3.18 mm) diameter gets you accurate measurements from -200 °C to 500 °C with only 80mm (3.1 in) of immersion. With multiple sheath length options on both of these probes, you can find the dimensions that are just right for your specific application. The 5608 comes with a one-eighth inch (3.18 mm) diameter sheath in lengths of 9 inches or 12 inches. The 5609 comes with a one-quarter inch (6.35 mm) diameter sheath in lengths of 12 inches, 15 inches, and 20 inches; or with a 6 mm diameter in lengths of 300 mm, 400 mm, or 500 mm. When looking for improved response time and reduced stem effect in shallow immersion, look for small diameter probes, because the measurement error called stem effect is caused by the diameter of the stem rather than the length of the stem. Both of these probes have InconelTM sheaths and are made using a special manufacturing process, giving them great precision over a wide temperature range. The sensors for these probes are reference-grade platinum and feature four-wire connections with less noisy measurements than two-wire counterparts. These probes come with a certificate of compliance to ensure the meet their specifications. If you'd like, you can also order a NVLAP-accredited calibration from our laboratory, lab code 200348-0. On the report of calibration, you'll get the test data and the ITS90 calibration coefficients that you can easily input into any Fluke Calibration thermometer
-
4.9 of 5.0 with 38 Reviews
SALE PRICE: $1,199.00 11% OFF
Manufacturer: CEM
Brand: Botterrun
Model: DT-980
Manufacturer: CEM
Brand: Botterrun
Model: DT-980
|
Botterrun CEM DT-980 Thermal Imagers is designed to make your work easier, more productive and effective. Specifications: Imaging and optical data IR Resolution: 80 x 80 pixels Focal Plane Array/Spectral Range: Uncooled microbolometer / 8-14μm Focal Length: 9mm Field of View: 17°x17° Minimum Focus Distance: 0.5m Spatial Resolution: 3.78mrad Thermal Sensitivity/NETD: < 0.1℃@+30℃(+86℉)/100mK Image Frequency: 50Hz Zoom: 1-32x continuous,digital zoom Image Presentation Image Modes: IR image, visual image, picture in picture Picture in Picture: IR area on visual image Color Palettes: iron/rainbow/grey/grey inverted Measurement Object Temperature Range: -20 to 150℃(-4 to 302℉) Accuracy: ±2℃(±3.6℉) or ±2% of reading Storage of Videos/Images Inside Memory: 100M bytes, about 80pictures or one minute video record Video Storage Format: Standard MPEG-4, 1280x960@30fps, on memory card > 60minutes Image Storage Format: Standard JPEG, including measurement data, on memory card > 6000 pictures Digital Camera Built-in Visible Light Digital Camera: 5 Megapixels Built-in Digital Lens Data: 59° Interfaces&Video Out: USB-Mini, audio, HDMI USB: Data&Live video transform between camera and PC or smartphone Package Include: 1 * Infrared Camera with Lens 1 * Earphone(Optional) 1 * Battery 1 * Software CD-ROM 1 * Wrist Strap 1 * 8GB Micro SD Card 1 * Adaptor 1 * USB Cable & HDMI Cable(Optional)
-
4.9 of 5.0 with 49 Reviews
SALE PRICE: $1,199.98
Manufacturer: Fluke
Brand: Fluke
Manufacturer: Fluke
Brand: Fluke
SILVER CAREPLAN TI10/TIR 2 YR
-
4.9 of 5.0 with 38 Reviews
SALE PRICE: $1,218.20 1% OFF
Manufacturer: NETCNA
Brand: NETCNA
Manufacturer: NETCNA
Brand: NETCNA
The 30mm Lens for OTS-X Thermal Monocular from ATN is an accessory optic for the OTS-X handheld thermal imaging device. An interchangeable lens mount system enables this lens to be connected to any configuration of the OTS-X monocular. The 30mm lens transmits a 22° angle of view on a 640x480 monocular, or a 11° angle of view on one of the 320x240 configurations.
-
4.9 of 5.0 with 44 Reviews
SALE PRICE: $1,295.00 1% OFF
Manufacturer: HT Instruments
Brand: HT Instruments
Manufacturer: HT Instruments
Brand: HT Instruments
|
HT Instruments COMBI 419 Multifunctional Meter for Safety Test on Installations Meter for Insulation test and Continuity of earth conductor test with use of remote probe. COMBI419 is an innovative multifunction installation tester designed to perform all safety test verifies on electrical installations in compliance to recently standards (VDE0100, BS7671 etc..), more than measure of leakage currents. The multifunction installation tester COMBI419 it's very easy to use and have a wide number of internal features which are selectable by using the multi language menu. The instrument permits, moreover, to start principal measures by using a special remote prove (PR400 optional accessory) particular useful to perform tests in very quickly mode and the AUTO internal function to perform sequential measurements of Global Earth Resistance, test on RCDs' and Insulation directly on sockets of civil installations. A contextual help menu selectable by user it's available for each measurement function and permits a valid information during connection of meter to the installation. The newest electronic function selector give to the meter a extreme rugged structure for perfect using "on field". A wide internal memory permits the saving of any measurements and the transfer to PC by serial port with dedicated software it's possible. Each measure it's saved with all the sub-results and test parameters with up to two ID locators (selectable by user on meter) in order to reach the exact point where the measure was performed. Help on line (available on each function) to support the user while connecting the instrument to the installation under measurement Each model permits the Start of measurements with remote probe (PR400 optional accessory) General menu to quickly selection of available test performed by meter (COMBI419 and COMBI420 models only)
-
4.9 of 5.0 with 4 Reviews
SALE PRICE: $1,399.98
Manufacturer: Fluke
Brand: Fluke
Manufacturer: Fluke
Brand: Fluke
SILVER CAREPLAN TI32/TIR32 2 YR
-
4.9 of 5.0 with 5 Reviews
SALE PRICE: $1,495.00 1% OFF
Manufacturer: HT Instruments
Brand: HT Instruments
Manufacturer: HT Instruments
Brand: HT Instruments
|
Ground Resistance and Bonding Continuity Tester New Icon Menu Easy to use and to connect Innovative Design     One instrument for all electrical safety tests according to IEC/EN61557-1. Earth resistance with 2- or 3-pole volt-ampere method in TT, TN and IT systems, non-trip earth loop impedance measurement. Measurement of electrical parameters in single phase installations (V, A ,W,VAR,VA, PF) Continuity measurement of protective conductors. Soil resistivity. Insulation resistance measurement. Stackless earth ground resistance measurement with T2100 (optional).  MACROTESTG1 EARTH GROUND | CONTINUITY | POWER QUALITY  MACROTEST G1 is an innovative multifunction installation tester capable of carrying out safety tests on civil and industrial electric systems in compliance with IEC/EN61557-1. Its resistive TFT color touch-screen display, its icon menu, its help-on-line and its user-friendly development make the instrument extremely intuitive even for unskilled users. Its numberless features grant the user a wide range of applications in the world of measurements. The multifunction installation tester MACROTEST G1 allows saving all measures into an internal memory so transferring the saved data to a PC by means of USB (provided as standard) or built in Wi-Fi interfaces with an iOS and Android smartphones or tablets.The software supplied among standard accessories allows printing testing reports.The multifunction installation tester MACROTESTG1 has as Optional clamp T2100 permits to quickly check the resistance of earth probes without disconnection from earth system
-
4.9 of 5.0 with 38 Reviews
SALE PRICE: $1,799.97
Manufacturer: Fluke
Brand: Fluke
Manufacturer: Fluke
Brand: Fluke
|
Maintenance and Extended Warranty Plans for Your Fluke Infrared Camera Repairs are always unexpected and they can be costly. Keep your camera in top operating condition and control your cost of ownership with a Fluke Silver CarePlan. Fluke CarePlans provide you the highest level of service at the best price available. They are easy to purchase and register. All Fluke CarePlans help you minimize your downtime and protect your investment in your Fluke infrared camera as coverage starts from the moment you register. Ensure your peace of mind by protecting your investment beyond your factory warranty by purchasing a 3 Year Fluke CarePlan. You can also extend your warranty for up to two additional years. Fluke CarePlans - Everything You Need to Make Your Life Easier and Worry-Free Silver CarePlan A comprehensive maintenance and extended warranty plan, including one annual performance check. Purchase this plan if you want free repairs and one annual free performance check, but not necessarily a calibration. Qualifying for Your CarePlan Purchase You may purchase your CarePlan at the time you order your new instrument or anytime within six months of original purchase date with proof of purchase from an authorized dealer (or from date of manufacture without proof of purchase). How to Purchase Pre-Purchase Registration is Required Careplan pre-purchase registration is required prior to processing your order. To pre- register simply go to CarePlans to download a CarePlan product registration form. You can also obtain a CarePlan registration form by contacting Fluke in your area. Complete this form and include it with your purchase order. When Does My Coverage Start? As soon as you receive your CarePlan documents and complete your on-line registration you begin enjoying your CarePlan benefits of First-on-bench priority handling, comprehensive repair coverage, Loaner services, annual performance checks or calibrations
-
4.9 of 5.0 with 15 Reviews
SALE PRICE: $1,896.00 14% OFF
Manufacturer: Testo
Brand: Testo
Manufacturer: Testo
Brand: Testo
The Testo 870-1 offers sharp, crisp, detailed, commercial quality images every time, right out of the box with the widest lens (34º x 26º) available. Stack this up with the easy 1-button control and you have a technologically advanced, well thought-out thermal imaging solution for Commercial Contractors, Facility Managers and Energy Auditors. The testo 8701 balances features and performance in an easy-to-use, small, compact design.
|
|