Pressure & Vacuum - Page 28

Manufacturer: Monarch Instrument Brand: Monarch Instrument Model: 5396-0301

The Track-It Pressure/Temperature Data Logger is a battery powered stand alone water tight compact data logger that records up to 64,000 samples of Pressure and/or Temperature data. It can be configured to record Pressure and Temperature or either parameter alone to maximize data storage space. The unit is easily configured using the included Track-It Software. Simply connect a standard USB cable to the logger and an open USB port on your PC and the Track-It™ Software automatically identifies the logger. Configure the unit to start and stop recording at a predetermined time and date or only when an alarm condition is sensed. The sample storage rate can be set from 1 sample every 2 seconds to 1 sample every 24 hours. The on board data storage is non-volatile so data will not be lost in the event of a depleted battery. The Track-It™ Pressure/Temperature Data Logger can be ordered in several pressure ranges: 0-35, 0-150, 0-350, 0-550 and 0-2000 PSI. The logger is packaged in a rugged submersible 316L stainless steel housing and has a standard 1/4” NPT fitting. The replaceable internal lithium battery has up to a 5 year life.

Manufacturer: General Wire Brand: General Wire Model: KR-D-WC Color: NA

The Kinetic Water Ram uses a burst of compressed air that drives a shock wave (kinetic energy) through water to break up stoppage. It's particularly useful when the stoppage is on the far side of a drum trap or series of tight bends, since the shock wave can travel around bends without losing its force.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-1503

The Fluke high-voltage digital megohmmeter is an insulation tester with preset and adjustable test voltages for measuring insulation resistance to 1TΩ (2TΩ for 10kV models) to indicate the condition of windings or cables in motors, switchgears, electrical installations, and other insulated equipment, and it also measures leakage current to 2 milliamperes (mA), capacitance to 20μF, and AC and DC voltage to 600V, signaling when a voltage greater than 30V is detected. In addition to the preset test voltages of 250V, 500V, 1,000V, 2,500V, 5,000V, plus 10,000V for the 10kV models, test voltages can be adjusted in 50V increments to 1,000V and 100V increments above 1,000V. Its PI/DAR (polarization index/dielectric absorption rate) function automatically calculates PI and DAR, which are measurements over time that give a truer indication of insulation condition than single-point measurements. The meter can perform timed tests up to 99 minutes, adjustable in 1-minute increments, and has storage for up to 99 test results. Stored results can be uploaded to a PC with the included FlukeView Forms Basic software. The software is compatible with Microsoft Windows 2000, XP, and Vista. For improved accuracy during high-resistance testing, the guard terminal eliminates interference from leakage current. The meter has an LCD that shows the reading numerically and in a bar graph. Megohmmeters are commonly used for electrical maintenance and testing in industries such as HVAC, transportation, manufacturing, mining, and utilities, among others. The meter is rated for category (CAT) IV installations to 600V, which covers equipment at the origin of the installation, such as electricity meters and primary over-current protection equipment, and CAT III installations to 1,000V, which covers equipment in fixed installations, such as switches in the fixed installation and some industrial equipment that is permanently connected to the fixed installation. The unit has a low-battery indicator that signals when the battery needs to be r...

Manufacturer: Missyee Brand: Missyee

Detail about Diesel Fuel Injector checker: Power:W Item Height:20 cm Brand Name: Voltage:V Model Name:Diesel Fuel Injector checker Item Width:30 cm Car Maker:Audi,Australia Ford,Benz,BMW,Brilliance,Chevro Hardware Version: 2016 Software Version: Diesel Fuel Injector checker Language: English External Testing Certification: CE Item Length: 50 cm Item Type: Pressure & Vacuum Testers Material Type: Metal and plastic Item Weight:5 kg fuel injector nozzle tester : 0 - 400 BAR / 0 - 6000 PSI Dual Scale Gauge BO-SCH injector checker is suitable for: all common rail injector and mechanical injectors Special Features:Diesel Injector Nozzle Tester Color:Black Quality:High Quality Place of Origin:Mainland China Price:Factory Price Is_customized:yes Unit Type: piece Package Weight: 5.000kg (11.02lb.) Package Size: 50cm x 30cm x 20cm (19.69in x 11.81in x 7.87in)

Manufacturer: Fluke Corporation Brand: Fluke Model: I30S

The i30s current clamp is based on hall effect technology for use in measurement of both DC and AC current. The i30s may be used in conjunction with oscilloscopes and other suitable recording instruments for accurate non-intrusive current measurement. Specified current range: 30 mA to 30A DC, 30 mA to 20 A AC rms. Usable current range: 5 mA to 30 A DC, 30 mA to 20 A AC rms. Crest factor: 1.4". Output sensitivity: 100 mV/A. Accuracy (at +25 degree C): +/-1 percent of reading +/-2 mA. Resolution: +/-1 mA. Load impedance: greater than 100 kilo ohm. Conductor position sensitivity: +/-1 percent relative to center reading. Frequency range: DC to 100 kHz (- 0.5 dB). Phase shift below 1 kHz: less than 2 degrees. Temperature coefficient: +/-0.01 percent of reading/degree C. Power supply: 9 V Alkaline, MN1604/PP3, 30 hours, low battery indicator. Working voltage (see Safety Standards section): 300 V AC rms or DC. Maximum conductor size: 19mm diameter. Output connection: Safety BNC connector, supplied with safety 4mm adapter. Output zero: Manual adjust via thumbwheel. Cable length: 2 meters. Operating temperature range: 0 to +50 degree C. Storage temperature range (with battery removed): -20 to +85 degree C. Operating humidity: 15 to 85 percent (non-condensing). Safety standards: BS EN 61010-1: 2001, BS EN 61010-2-032: 2002, BS EN 61010-031: 2002, 300 Vrms, Category III, Pollution Degree 2, Use of the probe on uninsulated conductors is limited to 300 V AC RMS or dc and frequencies below 1 kHz. EMC Standards: EN 61326: 1998 +A1, A2, and A3. Measures 71mm width by 183mm height by 25mm depth.

Manufacturer: Mid-West Instrument Brand: Mid-West Instrument Model: 845

Mid-West Instrument Backflow prevention assembly test kit includes 5 valve. The 835 is in the list of acceptable gages from both FCCC and HR-USC and CA-NV AWWA. Backflow test kits provide the capability for testing all brands of reduced pressure principle, pressure vacuum breaker, spill resistant vacuum breaker and double check valve backflow prevention assemblies. Over 30 years of input from Backflow technicians. Specially designed for testing backflow prevention assemblies. Soft-seated brass needle valves (with replaceable valve seats). Test kit is protected with 90 micron filters to minimize plugging with scale, sand, etc. Filter elements can be cleaned or replaced. Improved case with storage compartments for fittings and tools. Test procedures are laminated in clear plastic. 5 Year warranty. Gauge type diaphragm differential pressure. Dial size and range (4-1/2-inches) 0-15 psid/0-100 KPA. Differential pressure accuracy +/-0.2 P.S.I.D. (Descending). Working pressure: 200 psig. Body material: glass reinforced engineering thermoplastic. Wetted internals: EP elastomers, brass and 316 stainless steel metal parts. Line pressure gauge: 1-1/2-inches 0-200 psig. Hoses and end fittings: Buna-N jacket and liner. Schrader 1/4-inches brass coupler. Hose length: three (3) each/5-feet long (color-coded). Bleed tube, one each/4-feet long clear bleed tube. Adaptor fittings: (3) sets of brass fittings provided for hookup to all standard size test cocks. Temperature limitations: maximum 150 degree F/65 degree C. Measures 18-1/2-inches length by 9-inches width by 9-3/4-inches height. Freezing temperatures must be avoided.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-707

Loop Calibrator is a high performance solution for calibration, repair and maintenance of current loops. The new "Quick Click" knob making it extremely fast and easy to use. Large display and simple, quick-click interface for easy one-handed operation. Simultaneous mA and percent readout for quick, easy interpretation of readings. mA accuracy of 0.015 percent, superior to other loop calibrators in this price range. 1 microampere resolution for mA source, simulate and measure. Push button 25 percent steps for fast, easy linearity checks. 0-100 percent "span check" for fast confirmation of zero and span. Selectable slow ramp, fast ramp, and step ramp to provide smooth outputs for valve slewing and loop functional tests. 24 volt internal loop supply, so you can power and read a transmitter at the same time without carrying a DMM. Measures V dc to 28V. Single 9V battery that is easily changed without braking calibration seal 0 - 20 mA or 4 - 20 mA default start up modes. Innovative output adjustment dial with 1 microampere and 100 resolution. HART mode connects 250 O resistor in series with 24 V loop for compatibility with HART communicators. Current measurement: : 0 to 24 mA range, 0.001 mA resolution, 0.015 percent Rdg + 2 LSD accuracy. Voltage measurement: : 0 to 28V DC range, 1 mV resolution, 0.015 percent Rdg + 2 LSD accuracy. Loop power: while measuring mA, 24V. Operating temperature: -10/55 degree C. Storage temperature: -30/60 degree C. Measures 152mm length by 70mm width by 41mm depth. Including: protective yellow holster with test lead storage, instructions sheet (14 languages), single 9V alkaline battery, test leads and alligator clips, NIST- traceable calibration report and data. Weight: approx. 330 g (21 oz)

Manufacturer: Fluke Brand: Fluke Model: 4550041

Fluke 820 LED Stroboscope.

Manufacturer: General Wire Brand: General Wire Model: GIDDS-214230

The Mini-Rooter XP gives you extra portability because 8" semi-pneumatic wheels let you keep the weight on the ground. An easy-grip handle folds down to save space and locks to use as an additional lifting handle. A roll bar protects the 1/3 hip motor when going up or down stairs. And the power cord and foot pedal can be stowed away on convenient cord wraps. The XP gives you extra performance and value, enabling you to clear clogged drain lines from 1-1/4" to 4" in diameter with just one machine. The drum easily holds 75 feet of 3/8" or 1/2" cable and features a free floating inner drum with an integral distributor tube to help prevent cable tangling. By switching to the optional J-Drum or dual drum you can handle smaller drain lines. You'll want to equip your XP with a power cable feed too. It makes a lot of tough jobs go much easier. Even with the power cable feed option, the drum is a snap to remove, taking less than a minute. Of course the XP comes with an air foot pedal and ground fault circuit interrupter for safety and General's patented Flexi core wire rope center cable for durability.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-1587 MDT

The Fluke 1587 MDT advanced insulation and motor drive troubleshooting kit is designed for troubleshooting and preventive maintenance applications including three-phase motors, cables, switch gear, and in applications where testing is required without the need to break the circuit. The kit includes the Fluke 1587 digital insulation multimeter, Fluke i400 current clamp, and Fluke 9040 phase rotation indicator. The Fluke 1587 digital insulation multimeter (also known as a multitester) is a true RMS, auto- and manual-ranging meter insulation resistance, current, voltage, and resistance for testing line insulation in telecommunications applications. The insulation test voltage settings of 50V, 100V measure resistance from 0.01 to 100 megohms. The meter also measures capacitance, frequency, and resistance. Temperature is measured using a K-type thermocouple (included). A diode test detects correct functioning of a circuit's diodes. A low-pass filter provides accurate AC voltage and AC frequency measurements on inverters and variable-frequency motor drives by blocking unwanted voltages. Live circuit detection increases user safety by preventing insulation tests when voltages exceed 30V, and auto-discharge of capacitive voltage increases user protection. An audible continuity sensor confirms a circuit conducts electricity. The LCD is backlit for readability in low light. A hold function freezes the reading on the display. An alarm sounds when the test leads are connected to the wrong jack for the measurement being taken. The unit automatically turns off after 20 minutes of nonuse to conserve battery life or can be disabled for extended readings, and a low-battery indicator signals when the meter's batteries need to be replaced. The meter included a set of detachable test leads, a remote probe, alligator clips, a hard case, and instructions. This true RMS (root mean square) insulation multimeter provides accurate readings when measuring linear loads, such as standard induction motors and incandescent lights, where the c...