Viscometers - Page 8

Manufacturer: YF&EB Brand: YF&EB

Usually the product will be sent in 2-5 working days and takes about 3--9 business days to reach you Description GB / T 1723-93 design, suitable for measuring the viscosity of coatings and other related products (out of time not less than 20 seconds). Under certain temperature conditions, the time required for the quantitative sample to flow out of all of the pores of a given diameter is measured, denoted by S. Specification Capacity: 50ml, with round water bath Cylinder diameter: Φ51 ± 0.01mm Cylinder bottom line to groove height: 46 ± 0.2mm The inner cone angle is: 101o ± 30 ' Drain mouth: length 14 ± 0.02mm Hole diameter: Φ5.6 ± 0.02mm Model: QND-1 Material: Aluminum Note: If you need to be converted into kinematic viscosity PCT (mm2 / s) can refer to the following formula: T = 0.053 v + 1.0 T-flow time (s) v- kinematic viscosity (mm2 / s)

Manufacturer: BYK-Gardner USA Brand: BYK-Gardner Model: 0616

The BYK-Gardner 616 replacement bubble viscometer standard tube has a viscosity of approximately 151.9 centistokes (cSt), and is suitable for testing fluids such as resins and varnishes. The 9mL capacity sealed bubble tube standard is lettered F and has a bubble test time of approximately 1.67 seconds. Sample fluid viscosity is determined by comparing bubble rise time to those of bubble tube standards and choosing the closest match. The sealed standard tube has a 15-year shelf life and can be National Institute of Standards and Technology (NIST) recertified. This bubble viscometer standard tube is ASTM International certified and meets the ASTM International D1545 standard for testing viscosity. A viscometer, also called a viscosimeter, is an instrument used to measure the friction caused by the relative motion of a Newtonian fluid and a known surface, and is usually expressed in units of poise (P), centipoise (cP), pascal seconds (Pa s), and millipascal seconds (mPa s). Viscometers have several forms, including but not limited to falling ball, rotational, vibrating, capillary, funnel, and bubble. A falling ball viscometer measures the time it takes for a ball of known diameter and density to fall through fluid in a cylinder of known diameter. A rotational viscometer measures the force required to stir a fluid. A vibrating viscometer measures the power input necessary to keep the oscillator vibrating at constant amplitude while immersed in a fluid. A capillary viscometer has a narrow-bore vertical section with two printed marks that measure time required for a known volume of fluid to fall a known distance. A funnel viscometer, such as a Ford, Zahn, or Shell cup, measures the time it takes a known volume of fluid to flow from the base of a cone through a short tube. A bubble viscometer measures the time required for an air bubble to rise through a fluid. Viscosity measurements are used in laboratories, research and development, process control, and plant quality control applications. Some viscometers are manufac...

Manufacturer: BYK-Gardner USA Brand: BYK-Gardner Model: 0628

The BYK-Gardner 0628 replacement bubble viscometer standard tube has a viscosity of approximately 467.4 centistokes (cSt), and is suitable for testing fluids such as resins and varnishes. The 9mL capacity sealed bubble tube standard is lettered R and has a bubble test time of approximately 4.85 seconds. Sample fluid viscosity is determined by comparing bubble rise time to those of bubble tube standards and choosing the closest match. The sealed standard tube has a 15-year shelf life and can be National Institute of Standards and Technology (NIST) recertified. This bubble viscometer standard tube is ASTM International certified and meets the ASTM International D1545 standard for testing viscosity. A viscometer, also called a viscosimeter, is an instrument used to measure the friction caused by the relative motion of a Newtonian fluid and a known surface, and is usually expressed in units of poise (P), centipoise (cP), pascal seconds (Pa s), and millipascal seconds (mPa s). Viscometers have several forms, including but not limited to falling ball, rotational, vibrating, capillary, funnel, and bubble. A falling ball viscometer measures the time it takes for a ball of known diameter and density to fall through fluid in a cylinder of known diameter. A rotational viscometer measures the force required to stir a fluid. A vibrating viscometer measures the power input necessary to keep the oscillator vibrating at constant amplitude while immersed in a fluid. A capillary viscometer has a narrow-bore vertical section with two printed marks that measure time required for a known volume of fluid to fall a known distance. A funnel viscometer, such as a Ford, Zahn, or Shell cup, measures the time it takes a known volume of fluid to flow from the base of a cone through a short tube. A bubble viscometer measures the time required for an air bubble to rise through a fluid. Viscosity measurements are used in laboratories, research and development, process control, and plant quality control applications. Some viscometers are manufa...

Manufacturer: BYK-Gardner USA Brand: BYK-Gardner Model: 0645

The BYK-Gardner 0645 replacement bubble viscometer standard tube has a viscosity of approximately 1,737 centistokes (cSt), and is suitable for testing fluids such as resins and varnishes. The 9mL capacity sealed bubble tube standard is lettered Y and has a bubble test time of approximately 18.4 seconds. Sample fluid viscosity is determined by comparing bubble rise time to those of bubble tube standards and choosing the closest match. The sealed standard tube has a 15-year shelf life and can be National Institute of Standards and Technology (NIST) recertified. This bubble viscometer standard tube is ASTM International certified and meets the ASTM International D1545 standard for testing viscosity. A viscometer, also called a viscosimeter, is an instrument used to measure the friction caused by the relative motion of a Newtonian fluid and a known surface, and is usually expressed in units of poise (P), centipoise (cP), pascal seconds (Pa s), and millipascal seconds (mPa s). Viscometers have several forms, including but not limited to falling ball, rotational, vibrating, capillary, funnel, and bubble. A falling ball viscometer measures the time it takes for a ball of known diameter and density to fall through fluid in a cylinder of known diameter. A rotational viscometer measures the force required to stir a fluid. A vibrating viscometer measures the power input necessary to keep the oscillator vibrating at constant amplitude while immersed in a fluid. A capillary viscometer has a narrow-bore vertical section with two printed marks that measure time required for a known volume of fluid to fall a known distance. A funnel viscometer, such as a Ford, Zahn, or Shell cup, measures the time it takes a known volume of fluid to flow from the base of a cone through a short tube. A bubble viscometer measures the time required for an air bubble to rise through a fluid. Viscosity measurements are used in laboratories, research and development, process control, and plant quality control applications. Some viscometers are manufa...

Manufacturer: BYK-Gardner USA Brand: BYK-Gardner Model: 0643

The BYK-Gardner 0643 replacement bubble viscometer standard tube has a viscosity of approximately 1,073 centistokes (cSt), and is suitable for testing fluids such as resins and varnishes. The 9mL capacity sealed bubble tube standard is lettered W and has a bubble test time of approximately 11.5 seconds. Sample fluid viscosity is determined by comparing bubble rise time to those of bubble tube standards and choosing the closest match. The sealed standard tube has a 15-year shelf life and can be National Institute of Standards and Technology (NIST) recertified. This bubble viscometer standard tube is ASTM International certified and meets the ASTM International D1545 standard for testing viscosity. A viscometer, also called a viscosimeter, is an instrument used to measure the friction caused by the relative motion of a Newtonian fluid and a known surface, and is usually expressed in units of poise (P), centipoise (cP), pascal seconds (Pa s), and millipascal seconds (mPa s). Viscometers have several forms, including but not limited to falling ball, rotational, vibrating, capillary, funnel, and bubble. A falling ball viscometer measures the time it takes for a ball of known diameter and density to fall through fluid in a cylinder of known diameter. A rotational viscometer measures the force required to stir a fluid. A vibrating viscometer measures the power input necessary to keep the oscillator vibrating at constant amplitude while immersed in a fluid. A capillary viscometer has a narrow-bore vertical section with two printed marks that measure time required for a known volume of fluid to fall a known distance. A funnel viscometer, such as a Ford, Zahn, or Shell cup, measures the time it takes a known volume of fluid to flow from the base of a cone through a short tube. A bubble viscometer measures the time required for an air bubble to rise through a fluid. Viscosity measurements are used in laboratories, research and development, process control, and plant quality control applications. Some viscometers are manufa...

Manufacturer: BYK-Gardner USA Brand: BYK-Gardner Model: 8300

The BYK-Gardner 8300 S90-series Zahn-type viscosity cup has a 31 to 60 centistokes (cSt) viscosity range and is suitable for testing fluids such as cements and other adhesives. Efflux times range 15 to 78 seconds. It has a metal body with a 12-inch loop handle for hand-dipping into a liquid container and a finger-ring for maintaining a vertical position during use. The orifice diameter is calibrated against National Institute of Standards and Technology (NIST) for testing standard oils. It includes an ASTM certificate. This Number 1 Zahn-type viscosity cup meets ASTM D816 standard for testing rubber cements and ASTM D1084 standard for testing viscosity of adhesives. A viscometer, also called a viscosimeter, is an instrument used to measure the friction caused by the relative motion of a Newtonian fluid and a known surface, and is usually expressed in units of poise (P), centipoise (cP), pascal seconds (Pa s), and millipascal seconds (mPa s). Viscometers have several forms, including but not limited to falling ball, rotational, vibrating, capillary, funnel, and bubble. A falling ball viscometer measures the time it takes for a ball of known diameter and density to fall through fluid in a cylinder of known diameter. A rotational viscometer measures the force required to stir a fluid. A vibrating viscometer measures the power input necessary to keep the oscillator vibrating at constant amplitude while immersed in a fluid. A capillary viscometer has a narrow-bore vertical section with two printed marks that measure time required for a known volume of fluid to fall a known distance. A funnel viscometer, such as a Ford, Zahn, or Shell cup, measures the time it takes a known volume of fluid to flow from the base of a cone through a short tube. A bubble viscometer measures the time required for an air bubble to rise through a fluid. Viscosity measurements are used in laboratories, research and development, process control, and plant quality control applications. Some viscometers are manufactured to meet industry or gove...

Manufacturer: BYK-Gardner USA Brand: BYK-Gardner Model: 8308

The BYK-Gardner 8308 EZ-series Zahn-type viscosity cup has a 10 to 60 centistokes (cSt) viscosity range and is suitable for testing fluids such as cements and other adhesives. Efflux times range 79 to 784 seconds. It has a metal body with a 12-inch loop handle for hand-dipping into a liquid container and a finger-ring for maintaining a vertical position during use. The orifice diameter is calibrated against National Institute of Standards and Technology (NIST) for testing standard oils. It includes an ASTM certificate. This Number 4 Zahn-type viscosity cup meets ASTM International D4212 standard for measuring viscosity using dip-type cups, ASTM D816 standard for testing rubber cements, and ASTM D1084 standard for testing viscosity of adhesives. A viscometer, also called a viscosimeter, is an instrument used to measure the friction caused by the relative motion of a Newtonian fluid and a known surface, and is usually expressed in units of poise (P), centipoise (cP), pascal seconds (Pa s), and millipascal seconds (mPa s). Viscometers have several forms, including but not limited to falling ball, rotational, vibrating, capillary, funnel, and bubble. A falling ball viscometer measures the time it takes for a ball of known diameter and density to fall through fluid in a cylinder of known diameter. A rotational viscometer measures the force required to stir a fluid. A vibrating viscometer measures the power input necessary to keep the oscillator vibrating at constant amplitude while immersed in a fluid. A capillary viscometer has a narrow-bore vertical section with two printed marks that measure time required for a known volume of fluid to fall a known distance. A funnel viscometer, such as a Ford, Zahn, or Shell cup, measures the time it takes a known volume of fluid to flow from the base of a cone through a short tube. A bubble viscometer measures the time required for an air bubble to rise through a fluid. Viscosity measurements are used in laboratories, research and development, process control, and plant quality ...

Manufacturer: BYK-Gardner USA Brand: BYK-Gardner Model: 4890

BYK-Gardner 4890 Brookfield Viscometer, LV Spindle (Pack of 4)

Manufacturer: Cannon Instrument Brand: CANNON Instrument

The Cannon ZCAC-RO-9 Zeitfuchs cross-arm viscometer has a permanently attached 51mm diameter round metal holder and a 6,000 to 30,000 centistokes (cSt) viscosity measuring range. It is suitable for the measurement of either transparent or opaque Newtonian fluids such as fuels and lubricants. It uses a viscometer constant of 30 centistokes per second (cSt/s) for calculating kinematic viscosity of sample sizes as small as 1.0mL. The ZCAC-RO-series size 9 viscometer uses a 230mm depth water bath (not included) for temperature-control testing and a vacuum (not included) to draw a sample up for timed testing between two sets of printed marks. It includes an ASTM International certificate of calibration. This calibrated capillary-style viscometer meets the ASTM International D446 standard for viscometers and the D445 standard for testing viscosity. A viscometer, also called a viscosimeter, is an instrument used to measure the friction caused by the relative motion of a Newtonian fluid and a known surface, and is usually expressed in units of poise (P), centipoise (cP), pascal seconds (Pa s), and millipascal seconds (mPa s). Viscometers have several forms, including but not limited to falling ball, rotational, vibrating, capillary, funnel, and bubble. A falling ball viscometer measures the time it takes for a ball of known diameter and density to fall through fluid in a cylinder of known diameter. A rotational viscometer measures the force required to stir a fluid. A vibrating viscometer measures the power input necessary to keep the oscillator vibrating at constant amplitude while immersed in a fluid. A capillary viscometer has a narrow-bore vertical section with two printed marks that measure time required for a known volume of fluid to fall a known distance. A funnel viscometer, such as a Ford, Zahn, or Shell cup, measures the time it takes a known volume of fluid to flow from the base of a cone through a short tube. A bubble viscometer measures the time required for an air bubble to rise through a fluid. Viscosity ...

Manufacturer: COLE-PARMER Brand: Cole-Parmer

Take viscosity measurements of very thin paints, inks, solvents, adhesives, and coating materials of all kinds. Simply fill the cup by immersing it in the test liquid. After withdrawing the cup, measure the time it takes until the first break in the liquid stream. Each cup is supplied with a conversion table to determine viscosity in centistokes (cSt) from the elapsed time. Dip cups have an anodized aluminum handle for easy dipping and holding during timing. Replaceable orifice snaps in quickly and easily - no need to replace the whole cup. Standard Ford Dip Viscosity Cups have the same capacity as the Ford cups designed for use with a stand. Cup numbers 3 and 5 have a ±3% tolerance; cup number 4 has a ±2% tolerance. Feature handle for easy sample dipping - great for field testing Compatible with ASTM D 1200