|
|
-
5.0 of 5.0 with 5 Reviews
SALE PRICE: $29.80 22% OFF
Manufacturer: Testex
Brand: Testex
Manufacturer: Testex
Brand: Testex
|
The Press-O-Film X-Coarse Grade (1.5-4.5 mils / 40-115 microns) Replica Tape, Roll is used with a gauge to measure the surface roughness ("profile") of blast-cleaned steel. Testex Press-O-Film Replica Tape offers a unique replica technique and with a simple snap gauge will allow you to take accurate, low-cost blast-surface profile measurements. Testex makes surface replicas easy to obtain and produces average maximum peak-to-valley readings that ensure optimum blasting effectiveness. Replicas can be retained for future needs.The accuracy of Testex measurements is due to an innovative two-level film that can produce virtually exact replicas of the abrasive blast surfaces. The film is available in three different thickness grades to cover the most common range of blast profiles.Measurements can be taken in locations that are not possible using conventional stylus devices, e.g. internal pipe diameters and grooves, etc.Easy to use, remove the protective paper from the tape and place firmly on the blasted surface. Apply moderate pressure with the Burnishing Tool over the circular cut-out in the tape. Remove the tape. The replica is now ready for measurement using the Snap Gauge.
-
5.0 of 5.0 with 2 Reviews
SALE PRICE: $36.99 3% OFF
Manufacturer: Testex
Brand: Press-O-Film
Manufacturer: Testex
Brand: Press-O-Film
The Press-O-Film X-Coarse Grade (1.5-4.5 mils / 40-115 microns) Replica Tape Roll is used to measure the Testex Tape and determine the average maximum peak-to-valley height of the blasted profile. Measurements are made by firstly zeroing the gauge on 50m (2mils). This is to allow for the film backing. Place the replicated area between the anvils and gently lower the moveable anvil onto the film. The reading can now be taken, giving you the average peak-to-valley height of the blasted profile. Supplied in a Carrying Case with Burnishing Tool. The Testex Snap Gauge is available in a Test Kit, comprising 2 rolls of X coarse Testex (specify if you require other grades), Snap Gauge, Training Surface, Burnishing Tool and instructions.
-
4.8 of 5.0 with 20 Reviews
SALE PRICE: $31.99 15% OFF
Manufacturer: Testex
Brand: Testex
Manufacturer: Testex
Brand: Testex
|
The Press-O-Film Coarse Minus Grade (0.5-1.0 mils / 12-25 microns) Replica Tape, Roll is used with a gauge to measure the surface roughness ("profile") of blast-cleaned steel. Testex Press-O-Film Replica Tape offers a unique replica technique and with a simple snap gauge will allow you to take accurate, low-cost blast-surface profile measurements. Testex makes surface replicas easy to obtain and produces average maximum peak-to-valley readings that ensure optimum blasting effectiveness. Replicas can be retained for future needs.The accuracy of Testex measurements is due to an innovative two-level film that can produce virtually exact replicas of the abrasive blast surfaces. The film is available in three different thickness grades to cover the most common range of blast profiles.Measurements can be taken in locations that are not possible using conventional stylus devices, e.g. internal pipe diameters and grooves, etc.Easy to use, remove the protective paper from the tape and place firmly on the blasted surface. Apply moderate pressure with the Burnishing Tool over the circular cut-out in the tape. Remove the tape. The replica is now ready for measurement using the Snap Gauge.
-
4.7 of 5.0 with 44 Reviews
SALE PRICE: $48.99 13% OFF
Manufacturer: Testex
Brand: Testex
Manufacturer: Testex
Brand: Testex
|
The Press-O-Film X-Coarse Plus Grade (4-6.5 mils / 100-165 microns) Replica Tape, Roll is used with a gauge to measure the surface roughness ("profile") of blast-cleaned steel. Testex Press-O-Film Replica Tape offers a unique replica technique and with a simple snap gauge will allow you to take accurate, low-cost blast-surface profile measurements. Testex makes surface replicas easy to obtain and produces average maximum peak-to-valley readings that ensure optimum blasting effectiveness. Replicas can be retained for future needs.The accuracy of Testex measurements is due to an innovative two-level film that can produce virtually exact replicas of the abrasive blast surfaces. The film is available in three different thickness grades to cover the most common range of blast profiles.Measurements can be taken in locations that are not possible using conventional stylus devices, e.g. internal pipe diameters and grooves, etc.Easy to use, remove the protective paper from the tape and place firmly on the blasted surface. Apply moderate pressure with the Burnishing Tool over the circular cut-out in the tape. Remove the tape. The replica is now ready for measurement using the Snap Gauge.
-
4.5 of 5.0 with 37 Reviews
SALE PRICE: $41.99
Manufacturer: Testex
Brand: Testex
Manufacturer: Testex
Brand: Testex
|
The Press-O-Film Medium Grade (5-75 microinch / 0.1-2 microns) Replica Tape, Roll is used with a gauge to measure the surface roughness ("profile") of blast-cleaned steel. Testex Press-O-Film Replica Tape offers a unique replica technique and with a simple snap gauge will allow you to take accurate, low-cost blast-surface profile measurements. Testex makes surface replicas easy to obtain and produces average maximum peak-to-valley readings that ensure optimum blasting effectiveness. Replicas can be retained for future needs.The accuracy of Testex measurements is due to an innovative two-level film that can produce virtually exact replicas of the abrasive blast surfaces. The film is available in three different thickness grades to cover the most common range of blast profiles.Measurements can be taken in locations that are not possible using conventional stylus devices, e.g. internal pipe diameters and grooves, etc.Easy to use, remove the protective paper from the tape and place firmly on the blasted surface. Apply moderate pressure with the Burnishing Tool over the circular cut-out in the tape. Remove the tape. The replica is now ready for measurement using the Snap Gauge.
-
4.4 of 5.0 with 39 Reviews
SALE PRICE: $43.49
Manufacturer: Testex
Brand: Testex
Manufacturer: Testex
Brand: Testex
|
The Press-O-Film Medium Grade (5-75 microinch / 0.1-2 microns) Replica Tape, Roll is used with a gauge to measure the surface roughness ("profile") of blast-cleaned steel. Testex Press-O-Film Replica Tape offers a unique replica technique and with a simple snap gauge will allow you to take accurate, low-cost blast-surface profile measurements. Testex makes surface replicas easy to obtain and produces average maximum peak-to-valley readings that ensure optimum blasting effectiveness. Replicas can be retained for future needs.The accuracy of Testex measurements is due to an innovative two-level film that can produce virtually exact replicas of the abrasive blast surfaces. The film is available in three different thickness grades to cover the most common range of blast profiles.Measurements can be taken in locations that are not possible using conventional stylus devices, e.g. internal pipe diameters and grooves, etc.Easy to use, remove the protective paper from the tape and place firmly on the blasted surface. Apply moderate pressure with the Burnishing Tool over the circular cut-out in the tape. Remove the tape. The replica is now ready for measurement using the Snap Gauge
-
4.3 of 5.0 with 16 Reviews
SALE PRICE: $16.65 1% OFF
Manufacturer: JAMECO BENCHPRO
Brand: JAMECO BENCHPRO
Manufacturer: JAMECO BENCHPRO
Brand: JAMECO BENCHPRO
2-to-150mA LED Tester, T1 & T1¾ Features: Plug any leaded LED into any 2 rows of sockets Can also test common-anode and common-cathode multi-leaded LEDs 13.1" spaced positions test T1/T1¾ LE
-
4.3 of 5.0 with 49 Reviews
SALE PRICE: $42.50 8% OFF
Manufacturer: Testex
Brand: Testex
Manufacturer: Testex
Brand: Testex
|
The Coarse Minus Grade (0.5-1.0 mils / 12-25 microns), Roll is used with a gauge to measure the surface roughness ("profile") of blast-cleaned steel. Testex Press-O-Film Replica Tape offers a unique replica technique and with a simple snap gauge will allow you to take accurate, low-cost blast-surface profile measurements. Testex makes surface replicas easy to obtain and produces average maximum peak-to-valley readings that ensure optimum blasting effectiveness. Replicas can be retained for future needs.The accuracy of Testex measurements is due to an innovative two-level film that can produce virtually exact replicas of the abrasive blast surfaces. The film is available in three different thickness grades to cover the most common range of blast profiles.Measurements can be taken in locations that are not possible using conventional stylus devices, e.g. internal pipe diameters and grooves, etc.Easy to use, remove the protective paper from the tape and place firmly on the blasted surface. Apply moderate pressure with the Burnishing Tool over the circular cut-out in the tape. Remove the tape. The replica is now ready for measurement using the Snap Gauge
-
4.1 of 5.0 with 22 Reviews
SALE PRICE: $17.88
Manufacturer: JAMECO BENCHPRO
Brand: JAMECO BENCHPRO
Manufacturer: JAMECO BENCHPRO
Brand: JAMECO BENCHPRO
RS232 LINE STATUS TESTER Identifies simple interface problems. Features: Works on lines: 2-6 8 <
-
4.0 of 5.0 with 2 Reviews
SALE PRICE: $31.49 20% OFF
Manufacturer: Testex
Brand: Testex
Manufacturer: Testex
Brand: Testex
|
The Press-O-Film Coarse Grade (0.8-2.0 mils / 20-50 microns) Replica Tape, Roll is used with a gauge to measure the surface roughness ("profile") of blast-cleaned steel. Testex Press-O-Film Replica Tape offers a unique replica technique and with a simple snap gauge will allow you to take accurate, low-cost blast-surface profile measurements. Testex makes surface replicas easy to obtain and produces average maximum peak-to-valley readings that ensure optimum blasting effectiveness. Replicas can be retained for future needs.The accuracy of Testex measurements is due to an innovative two-level film that can produce virtually exact replicas of the abrasive blast surfaces. The film is available in three different thickness grades to cover the most common range of blast profiles.Measurements can be taken in locations that are not possible using conventional stylus devices, e.g. internal pipe diameters and grooves, etc.Easy to use, remove the protective paper from the tape and place firmly on the blasted surface. Apply moderate pressure with the Burnishing Tool over the circular cut-out in the tape. Remove the tape. The replica is now ready for measurement using the Snap Gauge.
|
|