Calibration - Page 176

Manufacturer: LK Industries Brand: L-K Industries Model: LK-TB300

Lk’s gasoline Test cylinder features solid Stainless steel construction. The unit is designed especially for the following ASTM tests.

Manufacturer: Fluke Corporation Brand: Fluke Model: MA190

Kit includes 50 ohm BNC insulated feed through terminator, 50 ohm BNC terminator with 10:1 signal attenuation, 1 ohm current shunt for current measurements, safety-designed BNC cable, 1.5m (5'), insulated BNC (f) to 4mm-banana plug adapter, dual 4mm banana receptacles (1 red, 1 black). The MA190 accessory set enables interconnection of the Fluke ScopeMeter 190 series for use in the field of medical imaging and video systems.

Manufacturer: Fluke Corporation Brand: Fluke Model: 709H/TRACK

Fluke Corporation introduces the Fluke 709H Precision Current Loop Calibrator with HART Communications, an affordable, easy-to-use tool with a user-friendly interface and HART capabilities that reduces the time it takes to measure or source, voltage or current, and power up a loop. With its best-in-class accuracy at 0.01 percent reading, the Fluke 709H is ideal for process technicians who need a precise loop calibrator and powerful HART communicator in one compact, rugged, reliable tool. The Fluke 709H supports a select set of HART universal and common practice commands. In the communicator mode, technicians can read basic device information, perform diagnostic tests, and trim the calibration on most HART-enabled transmitters. In the past, this could only be done with a dedicated communicator, a high-end multifunction calibrator, or a laptop computer with a HART modem. It also features a built-in, selectable 250-ohm resistor to tune the loop for HART communications. The 709H and non-HART 709 models feature an intuitive interface with dedicated buttons, a Quick-Set rotary encoder knob, and simple two wire connection for quick, easy measurements. The dedicated 0-100 percent span and 25 percent step buttons make for quick and easy testing. Ramping and auto-stepping enables technicians to perform tests remotely and be in “two places at once.” The optional 709H/TRACK software with communication cable can document milliamp measurements and HART transmitter parameters and upload to a PC.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-700-IV

4-20mA Current shunt. Very accurate current shunt to use for verification and calibration of process control loops. Can be used with accurate voltmeters for calibration purposes. Can be used with Fluke 74X series in mA/mA applications (74X will display mA/mA automatically). 1 year warranty.

Manufacturer: Meriam Process Technologies Brand: Meriam Model: ZB34686

961P Pressure pump with integral variator. Bleed valve. 1/8" FNPT connection. 0 - 145 PSIG. Pack of 1.

Manufacturer: ABS Import Tools Brand: HHIP

For 0 Ledge Surface Plate | Overall working height: 36" | Made of heavy-gauge steel with durable baked enamel finish. | Assembly required. | Stand comes with leveling screws

Manufacturer: Fluke Corporation Brand: Fluke Model: I1010

The Fluke i1010 AC/DC current clamp is designed to extend the current ranges of Fluke tools and can take current readings without breaking the circuit. Battery-powered dual Hall-effect, clamp-on probe measures dc current from 1-1000A; AC current from 1-600A AC rms. Measures AC and DC current down to 1 amp with specified accuracy and is useable to 0.5A. Output is 1 mV per amp DC or AC. Jaws accept conductor size of 1 X 750 MCM ( 30 mm/1.18 in. diameter) or 2 x 500 MCM (2 x 25 mm/0.98"). AC and DC accuracy: +/- (2.0 percent of reading + 0.5A). Measurement type: Hall sensor. Nominal current range: 600 A AC, 1000 A DC. Continuous current range: 1 A - 600 A AC, 1 A - 1000 A DC. Maximum non-destructive current: 1000 A. Lowest measurable current: 0.5 A. Useable frequency: DC - 10 kHz. Output levels: 1 mV/A. With zero error adjustment. Safety: CAT III, 600 V. Maximum voltage: 600 V. Battery life: 9 V, 60 h. Maximum conductor diameter: 30mm, 2 x 25mm. Output cable length: 1.6m. With shrouded banana plugs.

Manufacturer: Fluke Corporation Brand: Fluke Model: I1010-KIT

Kit included i1010 1-600A AC rms, 1-1000A DC current clamp, zippered vinyl carry case with moveable divider. Special value kit for electrical professional who is looking to add on DC and AC current measurement capabilities to their DMM. Includes a roomy carry case to hold and protect your meter and current clamp, plus extra storage for your test leads, probes and manuals. The Fluke i1010 AC/DC current clamp is designed to extend the current ranges of Fluke tools and can take current readings without breaking the circuit. Battery-powered dual Hall-effect, clamp-on probe measures dc current from 1-1000A; AC current from 1-600A AC rms. Measures AC and DC current down to 1 amp with specified accuracy and is useable to 0.5A. Output is 1 mV per amp DC or AC. Jaws accept conductor size of 1 X 750 MCM ( 30 mm/1.18 in. diameter) or 2 x 500 MCM (2 x 25 mm/0.98"). AC and DC accuracy: +/- (2.0 percent of reading + 0.5A). Measurement type: Hall sensor. Nominal current range: 600 A AC, 1000 A DC. Continuous current range: 1 A - 600 A AC, 1 A - 1000 A DC. Maximum non-destructive current: 1000 A. Lowest measurable current: 0.5 A. Useable frequency: DC - 10 kHz. Output levels: 1 mV/A. With zero error adjustment. Safety: CAT III, 600 V. Maximum voltage: 600 V. Battery life: 9 V, 60 h. Maximum conductor diameter: 30mm, 2 x 25mm. Output cable length: 1.6m. With shrouded banana plugs.

Manufacturer: Fluke Corporation Brand: Fluke Model: 3949761

Fluke 5A clamp-on current transformer for 1750 3 phase power quality recorder.

Manufacturer: Fluke Brand: Fluke Model: FLK-A3000 FC KIT

Fluke a3000 FC Wireless AC Current Clamp Module A fully functional true-rms current clamp meter that wirelessly relays measurements to other Fluke ConnectTM enabled master units, listed below. Fluke 3000 FC DMM Fluke Ti200/300/400 Infrared Camera PC via optional pc3000 FC Adapter Fluke Connect Mobile app Fluke Connect See it. Save it. Share it. All the facts, right in the field. Smart phone not included with purchase. Fluke Connect with ShareLive is the only wireless measurement system that lets you stay in contact with your entire team without leaving the field. The Fluke Connect mobile app is available for Android (4.3 and up) and iOS (4s and later) and works with over 20 different Fluke products-the largest suite of connected test tools in the world. And more are on the way. Go to the Fluke website to find out more. Make the best decisions faster than ever before by viewing all temperature, mechanical, electrical and vibration measurements for each equipment asset in one place.  Get started saving time and increasing your productivity.     Fluke 3000 FC Series Wireless Multimeter   Start building tomorrow's test tool system today with the Fluke 3000 FC Digital Multimeter. The new Fluke Connect system of test tools communicates with the new Fluke Connect mobile app on your AndroidTM or iOS smart device, allowing you to share live measurements, monitor readings from safe distances, and get your job done easier than ever before. The wireless digital multimeter functions as the mobile hub, displaying readings from up to three module tools simultaneously from up to 20 meters away. The Fluke Connect modules also give you the flexibility to build your wireless test tool system how you want when you want. The Fluke 3000 FC Wireless Test Tools are a team and the modules are team players