Calibration - Page 73

Manufacturer: Flexbar Brand: Flexbar

Rockwell Certified Hardness Test Block. "15N" Scale. Manufactured from the highest quality steel with a special heat treat and cold treat process which insures maximum consistency and repeatability. Accuracy exceeds ASTM E10, E18, E92 and E384 standards. HR15N 88.

Manufacturer: Flexbar Brand: Flexbar

NIST Traceable Rockwell Test Block. The new NIST Traceable Test Blocks for the Rockwell "C" Scale will provide complete traceability to NIST. These test blocks are ground, lapped and polished to a mirror finish of one micron. A NIST Traceable Certificate is furnished with each at no charge. HRCN 55

Manufacturer: Flexbar Brand: Flexbar

Rockwell Certified Hardness Test Block. A-Diamond. Manufactured from the highest quality steel with a special heat treat and cold treat process which insures maximum consistency and repeatability. Accuracy exceeds ASTM E10, E18, E92 and E384 standards. HRA 68

Manufacturer: Gasco Brand: Gasco

Calibration Gas, Gas Name Hydrogen Sulfide, Nitrogen, Gas Mixture 150 ppm Hydrogen Sulfide, N2, Background Gas Nitrogen, Cylinder Cylinder 44L, Cylinder Material Aluminum Alloy, For Use With Any and All OEM Gas Detectors, Connection Size C-10, Max. Pressure 825 psi, Cylinder Dia. 2-9/10 In.

Manufacturer: Gasco Brand: Gasco

Technical Specification Item Calibration Gas Gas Name Hydrogen Sulfide, Nitrogen Gas Mixture 10 ppm Hydrogen Sulfide, N2 Background Gas Nitrogen Cylinder Capacity 44L Cylinder Material Aluminum Alloy For Use With Any and All OEM Gas Detectors Connection Size C-10 Max. Pressure 825 psi Cylinder Dia. 2-9/10 Cylinder Height 10-1/2 Accuracy +/-5% Calibration Certificate NIST This listing is for each.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611150-516

All Mitutoyo gage blocks meet or exceed all known specifications. The flatness and parallelism surface finish necessary to achieve the required accuracies are the same as or better than government requirements. A certificate of inspection is furnished with all Mitutoyo gage blocks with a serial number on the case and an identification number on each block. The deviation of each block is registered. For this inspection, each gage block is measured relative to the upper level master using a gage block comparator. Grade K gage blocks are manufactured by absolute measurement using an interferometer. The gage block set and discrete gage block are supplied with a certificate of calibration. The certificate of calibration specifies the deviation from the nominal length. (Comparative measurement, however, is performed for all square gage blocks.). A certificate of accuracy, traceable to the NIST, is furnished with each Mitutoyo gage block set and individual block.

Manufacturer: Fluke Corporation Brand: Fluke Model: FVF-BASIC

FlukeView Forms Basic can be used alone to download measurement data and create reports that can be saved and printed. FlukeView Forms comes with an array of standard analysis and reporting forms that get you started on displaying your data in tables, graphs or helpful diagrams. You can leave notes on the forms to draw attention to a particular event. Share or store your data with co-workers or clients - print forms, export to other software programs, or have co-workers and clients down load the free FlukeView Demo/Reader to view and interact with your captured data. To address the increasing demands for reporting and documentation. It increases the power of your Fluke tool by enabling you to document, store and analyze individual readings or series of measurements, then convert them into professional-looking documents. The ability of FlukeView Forms to support multiple instruments enables the user to install and learn only one software application in order to use these multiple tools fully. Owners of Fluke 280 series, 180 series, 789 and 1550B, who do not need the full power of FlukeView forms, can use FlukeView Basic version. Transfer data points from your meter to your PC and use the two standard, non-customizable forms to display your readings in table or graphical form. For a larger array of forms or to use FlukeView Forms Designer to customize your forms, upgrade to FlukeView Forms version 3.3 with FVF-UG (sold separately). Comes with USB/IR cable. Number of standard forms: 2. Number of multiple meters whose data can be viewed simultaneously: 1. Number of concurrently running instances of FlukeView Forms allowed: 1. Requirements: Operating system: Windows 2000, Windows XP, Windows Vista or Windows 7. Minimum PC Hardware: Pentium class or better microprocessor, 32 MB RAM, 70 MB hard disk space (100 MB to install), USB port. FlukeView Forms supports the following test tools: 280 Series, 789, 1550B, 1653, 180 Series. Size: 203 x 100 x 50mm.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611117-516

All Mitutoyo gage blocks meet or exceed all known specifications. The flatness and parallelism surface finish necessary to achieve the required accuracies are the same as or better than government requirements. A certificate of inspection is furnished with all Mitutoyo gage blocks with a serial number on the case and an identification number on each block. The deviation of each block is registered. For this inspection, each gage block is measured relative to the upper level master using a gage block comparator. Grade K gage blocks are manufactured by absolute measurement using an interferometer. The gage block set and discrete gage block are supplied with a certificate of calibration. The certificate of calibration specifies the deviation from the nominal length. (Comparative measurement, however, is performed for all square gage blocks.). A certificate of accuracy, traceable to the NIST, is furnished with each Mitutoyo gage block set and individual block.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611144-516

All Mitutoyo gage blocks meet or exceed all known specifications. The flatness and parallelism surface finish necessary to achieve the required accuracies are the same as or better than government requirements. A certificate of inspection is furnished with all Mitutoyo gage blocks with a serial number on the case and an identification number on each block. The deviation of each block is registered. For this inspection, each gage block is measured relative to the upper level master using a gage block comparator. Grade K gage blocks are manufactured by absolute measurement using an interferometer. The gage block set and discrete gage block are supplied with a certificate of calibration. The certificate of calibration specifies the deviation from the nominal length. (Comparative measurement, however, is performed for all square gage blocks.). A certificate of accuracy, traceable to the NIST, is furnished with each Mitutoyo gage block set and individual block.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 616218-531

The Mitutoyo grade 0 square gage block is made of ceramic, has its nominal length engraved in inches, is supplied with a certificate of inspection, meets ASME B89.1.9.2002 standards, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 0 gage block is commonly used in workshop and inspection applications to calibrate and inspect mechanical parts and tools, to verify the accuracy of plug and snap gages, and to set electronic measuring devices. It is made of ceramic which resists corrosion, abrasion, and burrs, withstands high temperatures without melting (high thermal expansion resistance), and provides dimensional stability. This gage block has a rectangular base for accurate wringing. Nominal length is measured in inches, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.95 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to cal...