Thickness Gauges - Page 9

Manufacturer: DeFelsko Corporation Brand: DeFelsko Model: STDA1

Certified coating thickness standards are ideal for verifying the accuracy and operation of coating thickness gages and are an important component in fulfilling both ISO and in-house quality control requirements. Many organizations require verification of gage accuracy at the test site each time a coating thickness gage is put into service and at frequent intervals during use. Ideal for this purpose, Defelsko certified coating thickness standards have measured values traceable to a national metrology institution. Used to verify the accuracy and operation of any type 1 (mechanical) and type 2 (electronic) magnetic, eddy-current or ultrasonic coating thickness gage. Ideal for use in the calibration lab, in the field or on the factory floor. Standards with aluminum substrates consist of 4 plates mounted in a protective binder. Individually serialized for traceability to NIST or PTB - includes a certificate of calibration. Certified and labeled in both metric and imperial units. Defelsko A series epoxy on aluminum round metal plate. For PosiTector 6000 N, NS, NRS, FN, FNS, FNRS. Approximate thickness: zero for plate 1; 75 micrometer / 3 mils for plate 2; 250 micrometer / 10 mils for plate 3; 1500 micrometer / 60 mils for plate 4. Coating/ substrate: Epoxy on aluminum (non-ferrous). Accuracy: +/- 0.43 micrometer, +/- 0.017 mil. Plate Diameter: 38mm (1.5"); Measurement Diameter: 25mm (1").

Manufacturer: Starrett Brand: Starrett Model: 1010MZ Color: Yellow

Handy pocket gauge is approximately the size of a thin pocket watch. Ideal for inspectors, purchasing agents and salespeople to check the size of materials up to 3/8" thick. The gauge fits naturally into the curve between the thumb and index finger. A slight pull on the serrated top plate raises the spindle.

Manufacturer: XZB Brand: XZB

Auto Power Off Low Battery Indication Zero Point & Two Point Calibration Seven Point Calibration Max/min Data Recording Average/Standard Deviation Recording Single & Continuous Measuring Mode Option

Manufacturer: Dakota Ultrasonics Brand: Dakota Ultrasonics

The T-044-1000 High Temperature Dual Element Transducer, 2.25 MHz, 1/2" Diameter is a 1/2" diameter, 2.25 MHz dual element transducer. High Temperature (650F / 343C), potted cable, top in.

Manufacturer: Checkline Brand: Checkline

The RMU-30 Digital Thickness Gauge, Measuring Range 30 mm is used to determine the thickness of leather, textiles, cardboard, felt, rubber, sheet metal, foil, plywood, plastic, etc.

Manufacturer: M&A INSTRUMENTS INC Brand: M&A INSTRUMENTS INC Model: RUIYAN RY-LS300E

Introduction:RY-LS300 optical light source can provide 1 to 4 output wavelengths to meet specific requirements, including the 650nm red source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer needs.Together with the RY-PM-300 optical power meter,it is a perfect solution for the fiber optic network characterization Features:•Provides 1~4 output wavelengths which can be optional according to customers needs •CW,2Hz modulation output at 650nm,and CW, 270Hz,1KHz,2KHz modulation output at other wavelengths •High stability of the output power •Stable output wavelength •Backlight LCD display supports night operation •Compact size and decent appearance •Large LCD,easy operation Applications:•Maintenance in Telecom •Maintenance CATV •Test Lab of optical fibers •Other Fiber Optic Measurements Specifications:•Type:LS300E •Wavelengths(nm):850/1300/1310/1550nm •Emitter Type:FP-LD,LED or others please specify •Output Power(dBm):-6~-7(1310/1550nm),>0 (650nm) •Output Stability:+0.05dB/15mins; +0.1dB/ 8hours •Modulation Frequencies:CW/ 2(650nm)/270,1K,2K(1310nm/1550nm) •Optical Connector:FC/PC ( Interchangeable FC/SC/ST connectors can be optional) •Power Supply:Alkaline Battery(3 AA 1.5V batteries) •Battery Operating Time(hour):45 •Operating Temperature(oC): -10~+60 •Storage Temperature(oC):-25~+70 •Dimension(mm):172*82*33 Recommendation:RY-LS300 Handheld Light Source is designed for optimal use with RY-PM300 Optical Power Meter for measuring optical loss on both sigle mode and multimode fiber cable

Manufacturer: Phase II Plus Brand: Phase II Plus Model: UTG-2650

State of the art ultrasonic technology allows you to obtain ultra precise thickness measurements and store them to memory. This digital tester is capable of reading wall thickness down to 0.010" with a super high adjustable resolution of up to 0.0001". This dynamic sonic gauge is designed to measure the thickness of metallic and non-metallic materials such as steel, aluminum, titanium, plastics, ceramics, glass and any other good ultrasonic wage conductor as long as it has parallel top and bottom surfaces. The will accurately display readings in either inch or millimeter after a simple calibration to a known thickness or sound velocity.

Manufacturer: Phase II Plus Brand: PHASE II

The Phase II PTG-3525 can perform two different methods of calculating thickness measurement by utilizing the characteristics of both eddy current and magnetic induction. Testing performance is both non-destructive and extremely accurate. With this state of the art thickness gage, you can easily detect the thickness of non-magnetic coating on a magnetic substrate (ferrous) or an insulating coating on a non-magnetic conductive substrate (non-ferrous) utilizing our version that comes with 2-external probes. The PHASE II PTG3525 can be used in many areas of industry including manufacturing, general engineering, commercial inspection, etc. Min. radius of curvature: Convex: 0.12" (3 mm)--Concave: 1.2" (30 mm)--Min. substrate thickness: (Ferrous) 20 mils (0.5 um)--Non-ferrous: 2 mils (50 um)--Calibration: Zero Calibration--Foil calibration--Max. Surface temperature of test object: 302 degrees F (contact time max is 2 seconds)

Manufacturer: DeFelsko Corporation Brand: DeFelsko Model: FRS

Right angle probe for measuring within areas of low headroom. These constant-pressure, stainless steel probes are hermetically sealed to be totally waterproof-ideal for underwater use. 90 Degree regular separate probe. Heavy-duty, gold-plated locking connector for industrial environments. Certificate of calibration (long form) traceable to NIST included with every probe. Each probe retains its own unique calibration information (allowing full probe interchangeability). For ferrous metals (steel and cast iron). Two (2) year probe warranty. 0-60 mils (0-1500 micrometer) measuring range and +/-(0.05 mils + 1 percent) 0 - 2 mils, +/-(0.1 mils + 1 percent) greater than 2 mils and +/- (1 micrometer + 1 percent) 0-50 micrometer, +/- (2 micrometer + 1 percent) greater than 50 micrometer accuracy.

Manufacturer: Checkline Brand: Checkline

The J-40-L Digital Thickness Gauge for Leather, DIN 53326 (New 2589) is a precision instrument used to determine the material thickness of non-woven fabrics, textiles, felts, geomaterials, paper, floor coverings, leather, foils, etc. This low-cost thickness gauge is suitable for quick comparison measurements. The instrument does not meet the DIN, EN and ISO standards. The feeler shape and the pressure are corresponding to DIN EN ISO 5084 standards.