Dimensional Measurement - Page 1203

Manufacturer: Vermont Gage Brand: Vermont Gage

Vermont Gage's thread gages inspect the pitch diameter and the functional thread for both internal and external threaded products. All thread gages are marked with nominal size, class of fit and pitch diameters.

Manufacturer: Meda - Superior Import Brand: MEDA - SUPERIOR IMPORT

Interchangeable anvils permit quick accurate measurement of tubing, cylindrical walls, from a hole or slot to an edge, and many hard-to-reach locations. *5 key Deluxe Model micrometer head *Friction thimble for exact repetitive readings. *Chrome-Plated frame. *Carbide-tipped spindle.

Manufacturer: Linsen Tool Co.,LTD Brand: Linsen

Each set of M75 x 4 thread plug gage 100% calibrated with quality assurance in our factory. If clients need long form calibration certificate, we can send to professional third party testing lab ISO17025 accredited to get. it need USD35 extra fee per set.each set including GO NOGO.We will send out goods by DHL, Fedex or UPS. Clients can expect goods in quick time. As too many items in stock, we haven't take pictures one by one, the picture showed just for reference.

Manufacturer: Flexbar Brand: Flexbar

Flexbar Sensing-Saf-Start. The inexpensive Solution to OSHA. Anti-automatic Restart Protection Without the High Cost of Magnetic Motor Starters This is a mandatory OSHA safety requirement. With the Sensing-Saf-Start correctly installed on existing equipment, it will Provide Protection against unexpected start-up, motion, and motor burn-out in the following manner: Voltage drop or power interruption Protection. in the event equipment, while being operated (switch in the "On" Position), should stop due to loss or drop of Electrical power due to Power Failure from any cause, the Sensing-Saf-Start will automatically Disconnect and shut off power to the equipment, so that upon restoration of power, the equipment will Not start up even though the power switch to the equipment is in the "On" Position. in order to restore power to the equipment, the equipment switch must be turned "off" first, and then the ReSet button on the Sensing-Saf-Start depressed. in the event the equipment is inadvertantly unplugged and then Plugged Back into the power source while the equipment switch is in the "On" Position, the equipment will Not restart until the Reset button on the Sensing-Saf-Start is depressed. The Sensing-Saf-Start is intended for installation on equipment which operates on 120-volts or 240-volts A.C. and which is connected to the source of Electric power by means of a 3-Wire Flexible power Cord. The following Standards apply to Machines Driven by 120 volt and 240 volt motors: OSHA (US Occupational Safety and Health Administration 29 DFR #1910.213 (b) (3)*) NFPA (Electrical Standard for industrial Machinery, 1997 Edition, Section 8, Protection) Model No. 17024., 20" Cord on equipment switch End. 8' Cord on power End (No Plug). You must instAll matching Plugs. Rated 200 to 240-volt A.C., 15-amp (Single phase) 2 H.P. maximum, 50/60 cycle.

Manufacturer: iGaging Brand: iGaging Model: 36-LM40

Igaging Super high precision measuring microscope illuminated and distortion free. Features: distortion free. Extreme high resolution. 20x (4x Objective and 10x eyepiece) Lighted by Super bright 3 LEDs. Can be used in total darkness! reticle precision: 0.002"/0.05mm max measuring: 0.12"/3mm. Reticle has fine 90 degree crosshairs in center. Adjustable focal point for 2-1/2 inch vertical movement flexible rubber eyepiece. Stand included.

Manufacturer: Accusize Co. Ltd. Brand: Accusize Industrial Tools Model: 2312-3010

Range: 50-75mm/2-3" Resolution: 0.001mm.(0.00005") Accuracy: ±0.003mm mm/inch conversion. ABS/INC switchable. Reset/Pre-set. Hold function. Hold function for max. or min. values. Non-rotating spindle. Blade penetration = 0.315" Blade thickness = 0.03" Blade width = 0.256"

Manufacturer: Westward Brand: Westward

Vernier Depth Micrometer, Range 0 to 4 In, Base Length 4 In, Number of Rods 4, Ratchet Stop, Rod Dia 0.177 In, Graduations 0.001 In, Steel, Hardened and Ground, Rods of Carbon Steel, Locking Clamp, Finish Satin Chrome, Meets/Exceeds Federal Specifications For Accuracy, Includes Spanner Wrench and Case

Manufacturer: Accusize Co. Ltd. Brand: Accusize Industrial Tools Model: 3011-5051

Manufacturer: Merlintools Brand: Merlintools

metric M56 x 2.0mm set thread ring gage.

Manufacturer: Vermont Gage Brand: Vermont Gage

Vermont Gage's thread gages inspect the pitch diameter and the functional thread for both internal and external threaded products. All thread gages are marked with nominal size, class of fit and pitch diameters.