|
|
-
3.8 of 5.0 with 28 Reviews
SALE PRICE: $159.00 1% OFF
Manufacturer: Flexbar
Brand: Flexbar
Manufacturer: Flexbar
Brand: Flexbar
|
Flexbar Sensing-Saf-Start. The inexpensive Solution to OSHA. Anti-automatic Restart Protection Without the High Cost of Magnetic Motor Starters This is a mandatory OSHA safety requirement. With the Sensing-Saf-Start corRectly instAlled on existing equipment, it will Provide Protection against unexpected start-up, motion, and motor burn-out in the following manner: Voltage drop or power interruption Protection. in the event equipment, while being operated (switch in the "On" Position), should stop due to loss or drop of Electrical power due to Power Failure from any cause, the Sensing-Saf-Start will automatically Disconnect and shut off power to the equipment, so that upon restoration of power, the equipment will not start up even though the power switch to the equipment is in the "On" Position. in order to restore power to the equipment, the equipment switch must be turned "off" first, and then the ReSet button on the Sensing-Saf-Start depressed. in the event the equipment is inadvertantly unplugged and then Plugged Back into the power source while the equipment switch is in the "On" Position, the equipment will Not restart until the Reset button on the Sensing-Saf-Start is depressed. The Sensing-Saf-Start is intended for installation on equipment which operates on 120-volts or 240-volts A.C. and which is connected to the source of Electric power by means of a 3-Wire Flexible power Cord. The following Standards apply to Machines Driven by 120 volt and 240 volt motors: OSHA (US Occupational Safety and Health Administration 29 DFR #1910.213 (b) (3)*) NFPA (Electrical Standard for industrial Machinery, 1997 Edition, Section 8, Protection) Model No. 17025., Short Extension Cord Style. 14" Cord on male Plug End, 12" Cord on female receptacle End. Rated 120 volts, A.C., 15-amp, 3/4 HP motor maximum, 50/60 cycle.
-
3.8 of 5.0 with 19 Reviews
SALE PRICE: $159.29 1% OFF
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 128-101
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 128-101
|
The Mitutoyo Series 128 Vernier Depth Gauge, Micrometer Type, Metric, have a measurement range of 0 to 25mm, a resolution (or smallest graduation interval) of 0.01mm, with + or – 0.003mm of accuracy. The vernier scale provides precise measurements. These gauges include a 4mm diameter measuring rod for flexibility in measuring range. The units have a ratchet stop for uniform pressure and a measuring rod clamp for stability. They have a satin chrome finish on the thimble for readability. They are available with a base either 63.6mm or 101.6mm long. Depth gauges are typically used in manufacturing, machining, and mechanical engineering. Depth gauges are precision measuring instruments used to determine the depth of any shape that has a step, groove, or slot. These gauges often take the form of sliders that travel on a measuring beam or rods, are moved to position by hand, and then adjusted with a calibrated screw. The base of the gauge rests at the top of the shape whose recession is to be measured, while the beam or rods extend to the bottom of the recession to determine the measurement. Gauge position is read from a graduated scale, dial, counters, or an electronic display.Mitutoyo manufactures precision measuring tools, metrology equipment, and related systems. The company, founded in Tokyo in 1934, formed Mitutoyo America Corporation in 1963 with headquarters in Aurora, IL.
-
3.8 of 5.0 with 15 Reviews
SALE PRICE: $159.34 21% OFF
Manufacturer: Johnson Level & Tool
Brand: Johnson Level & Tool
Model: 1876-4800
Manufacturer: Johnson Level & Tool
Brand: Johnson Level & Tool
Model: 1876-4800
Johnson level & tool 1876-4800 48'' Electronic Digital Box Level Extremely accurate with .05 degree at 0 degrees and 90 degrees and quick horizontal and vertical calibration, Angle inclination in 5 construction languages - units of measure (degrees, percent, in/ft (fractional), in/ft (decimal), mm/m, Automatic digit inversion for overhead measurements and working range on angle measurement is 4 x 90 degrees, Reference function making any slope "0.0" and hold function locks measurement on the LCD, SurroundView vials reflect ambient light for easy-read
-
3.8 of 5.0 with 9 Reviews
SALE PRICE: $159.99 1% OFF
Manufacturer: CEM
Brand: CEM
Manufacturer: CEM
Brand: CEM
|
Coating Thickness Tester DT-156 Features: •Non-magnetic coating on steel •Insulating coatings on no-ferrous metals •No-ferrous metals coatings on insulating substrates •Menu operation system •Two measuring mode: CONTINUR and SINGLE mode •Two working Mode: DIRECT and GROUP mode •Statistic Display: AVG,MAX,MIN,NO.,S.DEV •One point calibrating,two points calibrating and basic calibrating easily •Memory for 400 readings (80 DIRECT and 320 GROUP readings) •Delete single readings and group readings easily •High alarm and low alarm for all working mode •Low battery error indication •USB interface for PC software (windows 98/2000/xp/vista) Specifications: •Two measuring mode: CONTINUE and SINGLE mode •Two working Mode: DIRECT and GROUP mode 1. Sensor probe F •Working principle: Magnetic induction •Measuring range: 0 to 1250um •Guaranteed tolerance (of reading): (+/- 3%+1)um •Low range Precision: 0.1um •Minimum curvature radius: 1.5mm •Diameter of Minimum area: 3mm •Basic critical thickness: 0.5mm 2. Sensor probe N •Working principle: Eddy current principle •Measuring range: 0 to 1250um •Guaranteed tolerance (of reading): (+/- 3%+1.5)um •Low range Precision: 0.1um •Minimum curvature radius: 3mm •Diameter of Minimum area: 5mm •Basic critical thickness: 0.3mm •Dimensions: 113.5mm * 54mm * 27mm(H*W*D)
-
3.8 of 5.0 with 14 Reviews
SALE PRICE: $160.37 1% OFF
Manufacturer: Fowler
Brand: Fowler
Manufacturer: Fowler
Brand: Fowler
Includes case Fowler's Dial Thickness Gages are light in weight, easy to handle and carry. These specially built gages are mounted in a hand contoured frame with a thumb release mechanism; has fast direct reading to .001". Used to measure thickness of paper, cellophane, plastic film and metal plates. These are high quality precision instruments. Features Case finished in dull plated chrome. Direct reading 0-100 (with revolution counter) on easy-to-read dial Frame is hammertone baked enamel Microfine graduations for .001" or .01mm minimum reading Spindle of hardened stainless steel Features a thumb release mechanism
-
3.8 of 5.0 with 49 Reviews
SALE PRICE: $160.99 1% OFF
Manufacturer: Freud Tools
Brand: Freud Tools
Manufacturer: Freud Tools
Brand: Freud Tools
Create a uniform chamfer on the edge of any work piece to add character, while retaining crisp geometric linesChamfer Size easily adjusts by changing the height of the bit.Cut all composition materials, plywoods, hardwoods, and softwoodUse on hand-held and table mounted portable routers2 Flute design for efficient cutting and dust removalCutter Diameter: 2-1/2 inch Carbide Height: 1 inch Overall Length: 2-7/8 inch Angle: 45?Bearing Diameter: 1/2 inch Shank Diameter: 1/2 inch.
-
3.8 of 5.0 with 50 Reviews
SALE PRICE: $161.86
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 571-100MOT-10
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 571-100MOT-10
|
The Mitutoyo Series 571, 700 Tire Tread LCD Depth Gauges, Metric, depending on the model, has a range of 0 to 25mm, a resolution (or smallest graduation interval) of either 0.01mm with + or 0.02mm of accuracy, or 0.1mm with + or - 0.2mm of accuracy. The LCD interface displays in metric. The gauges in this series are designed specifically to measure tire tread groove depth. The 571 models keep track of the origin point, once set, for the life of the battery (about 2 years) for accuracy. The display has origin-set (Series 571-only), zero, and SPC data output (Series 571-only) functions for the users' convenience. The gauges in Series 700 are made of plastic so that they are lightweight to use. The gauges conform to European Conformity (CE) marking.. The gauges in this series include an SR44 battery. Optional SPC cables and an LCD with data hold are sold separately for Series 571 models. Depth gauges are typically used in manufacturing, machining, and mechanical engineering. Depth gauges are precision measuring instruments used to determine the depth of any shape that has a step, groove, or slot. These gauges often take the form of sliders that travel on a measuring beam or rods, are moved to position by hand, and then adjusted with a calibrated screw. The base of the gauge rests at the top of the shape whose recession is to be measured, while the beam or rods extend to the bottom of the recession to determine the measurement. Gauge position is read from a graduated scale, dial, counters, or an electronic display.Mitutoyo manufactures precision measuring tools, metrology equipment, and related systems. The company, founded in Tokyo in 1934, formed Mitutoyo America Corporation in 1963 with headquarters in Aurora, IL.
-
3.8 of 5.0 with 33 Reviews
SALE PRICE: $162.00 1% OFF
Manufacturer: Hexagon Metrology
Brand: Brown & Sharpe
Color: White
Manufacturer: Hexagon Metrology
Brand: Brown & Sharpe
Color: White
|
Essential for the workshop, but also in the inspection room or measuring laboratory - Ideal for comparative measurement on a surface plate - Detect form and position errors - Measure axial and radial runouts, especially. Technical features: long range up to 3mm, bidirectional measurin, without reversing lever, continuous two-way clockwise rotation of the pointer, swivelling probe through 180 degree, main pivot on oversize, self-aligning angular bearings, dovetail mounting machined in the indicator body, dull-chrome plated bezel and housing, rotating dial, insensitive to magnetic fields generated in common precision mechanics. Note for use of compac dial test indicators: with the measuring insert lying parallel to the workpiece surface, these dial test indicators give true reading due to the amplification factor to 1:1. In any other measuring position, the effective lever length changes so that the read value need be corrected. With respect to this, also read in the instruction manual. Tesa design swiss made. Standard DIN 2270 and factory standard. Friction lever system to preventing overload. Contact points with tungsten carbide ball tips. Delivery in a suited plastic case including: 1 contact point, 2mm dia, 1 rigid stem with 8mm dia, L = 15mm No. 01840107. 1 rigid stem with 4mm dia, L = 15mm No. 01840109. Identification number. Inspection report with a declaration of conformity.
-
3.8 of 5.0 with 11 Reviews
SALE PRICE: $163.12 17% OFF
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 101-120
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 101-120
|
The Mitutoyo 101 series outside micrometer has a tapered frame for measuring narrow slots and tight spaces, a vernier scale in inch units for taking precise outside diameter (OD) measurements, and a ratchet-stop mechanism for uniform pressure during adjustment. The micrometer’s frame, thimble and sleeve have a satin chrome rust- and glare-resistant finish. The vernier scale on the thimble and sleeve is graduated to 0.0001â€. The spindle and anvil have flat measuring faces and are carbide-tipped for wear resistance. A spindle lock helps provide secure locking of the measurement position. The unit comes with a fitted plastic case for storage.Micrometers are precision measuring instruments that use a calibrated screw to measure small distances. These measurements are translated into large rotations of the screw that are then able to be read from a scale or a dial. Micrometers are typically used in manufacturing, machining, and mechanical engineering. There are three types of micrometer: outside, inside, and depth. Outside micrometers may also be called micrometer calipers, and are used to measure the length, width, or outside diameter of an object. Inside micrometers are typically used to measure interior diameter, as in a hole. Depth micrometers measure the height, or depth, of any shape that has a step, groove, or slot.Mitutoyo manufactures precision measuring tools, metrology equipment, and systems. The company was founded in Tokyo in 1934 and formed Mitutoyo America Corporation in 1963, which is headquartered in Aurora, IL.
-
3.8 of 5.0 with 16 Reviews
SALE PRICE: $164.68 1% OFF
Manufacturer: Mitutoyo
Brand: Mitutoyo
Manufacturer: Mitutoyo
Brand: Mitutoyo
Technical Specification Item Test Indicator Series 515 Design Horizontal Reading Balanced Graduations 0.01mm Range 0.8mm Range per Revolution 0.8mm Dial Reading 0-40-0 Contact Points Carbide Ball Dial Size (In.) 40mm Bearings Jeweled Bezel Adjustable Color Yellow Features Jeweled Bearings, Glare Free Scratch Resistant Crystal Standards Meet or Exceed American Gage Design Specifications Includes Test Ind., 2mm Carbide Point, 8mm Stem, Clamp Ring, Case Compliance & Restrictions Compliance and Restrictions None This listing is for each. Features Anti-magnetic Jeweled bearings No clutch structure Water and dust resistant Glare free crystal with scratch resistant coating Model513-404EAccuracy8?mSetBasicRange0.8mmGraduation0.01mmDial Reading0-40-0
Viewing Page 1204 of 1520
|
|