Dimensional Measurement - Page 1286

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 141-215

The Mitutoyo 141 series vernier inside micrometer includes a set of interchangeable rods for a diversified range of measurement, and has a vernier scale in inch units for making precise inside dimension (ID) measurements. The micrometer and rods have a satin chrome rust- and glare-resistant finish. The measuring faces are carbide-tipped for wear resistance. The vernier scale is graduated to 0.001”. A locking clamp helps hold measurements in place. The micrometer and accessories come with a fitted case for storage.Micrometers are precision measuring instruments that use a calibrated screw to measure small distances. These measurements are translated into large rotations of the screw that are then able to be read from a scale or a dial. Micrometers are typically used in manufacturing, machining, and mechanical engineering. There are three types of micrometer: outside, inside, and depth. Outside micrometers may also be called micrometer calipers, and are used to measure the length, width, or outside diameter of an object. Inside micrometers are typically used to measure interior diameter, as in a hole. Depth micrometers measure the height, or depth, of any shape that has a step, groove, or slot.Mitutoyo manufactures precision measuring tools, metrology equipment, and systems. The company was founded in Tokyo in 1934 and formed Mitutoyo America Corporation in 1963, which is headquartered in Aurora, IL.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 543-470B

Display: LCD, length standard: absolute electrostatic capacitance type linear encoder, max. Response speed: unlimited, measuring force: refer to the list of specifications, battery: sr44 (1 pc.), 938882, battery life: approx. 5,000 Hours under normal use, dust/water protection level: ip42 or ip53 (dust-proof type) origin-set/preset, zeroset, go/+/-ng judgment, counting direction switching, power on/off, data output, inch/mm conversion (on inch/metric models only).

Manufacturer: Starrett Brand: Starrett Model: 84Z-134-5J

The Starrett 84Z-134-5J Dial Bore Gauge has a measurement range of 3 to 5.1875" and gradient spacing of 0.0005". Two centralizing plungers provide accurate tool alignment within the bore. This direct-measuring gauge uses a two-point contact system for detection of geometry problems such as ovality and taper. Contact points are made of hardened tool steel contact points for wear resistance and are spring-loaded for sensitivity. The housing and knurled handle are made of aluminum for a lightweight feel and good balance. Dial indicators have jewel bearings for sensitivity and the gauge is furnished in a finished wood case.Bore gauges measure holes, or bores, in a workpiece. They can measure the interior diameter of a hole at any depth, while internal micrometers can only measure to the depth of their teeth. Bore gauges are typically calibrated with a setting ring and come in two types: simple and direct-measuring. Simple bore gauges are used with a caliper to transfer the hole measurement, while the more complex gauges take the measurement directly, and display it through a vernier, dial, or digital display. Bore gauges have a two- or three-point contact, indicating how many points on the gauge head touch the inside of the bore. Two-point contacts are better at measuring ovality, while three-point contacts are used to measure lobing or triangular form error. Pistol-grip bore gauges are used for fast, single-handed operation with repeatable results from one operator to another. Bore gauges can also be used in special applications, such as measuring threads, spline pitch diameters, and deep bores.The L.S. Starrett Company manufactures precision measuring tools, metrology and testing equipment, and saw blade products. The company, founded in 1880, is headquartered in Athol, MA.

Manufacturer: INSIZE Brand: INSIZE Model: ISP-A3000-SCALE50

50mm/1. 97" reading scale.

Manufacturer: Flexbar Brand: Flexbar

Flexbar E.I.M.B. Electrical interlocking Mounting Brackets. for use With All Flexbar Latheguards and Small Chuckguards. 4 Models Available to suit individual lathe designs. Functioning: Once Wired to motor-control circuit (motor starter), the cam-operated limit switch opens the contacts when the safety shield is tilted up . . . and the Machine stops running. Specifications: Limit switch: Roller-Type Roller and Head are metal in sealed Plastic housing. Electrical life - 1 million cycles. Mechanical life - 30 million cycles. NEMA 4 rated. Approvals: UL A300, UL E140497, CSA A 300 & CSA LR26716 M20. Snap acting SPDT inO-inC With Double break ensures switch will open in event of minor contact welding. Contact Block & roller Head are modular hence replaceable Without Discarding entire device Electrical Conduit: Extremely Flexible and Withstands repeated Flexing. UL recognized - exceeds industry Standards. Liquid tight vs. oil, Water and most chemicals *Fittings: inside is nylon With BUNA-N gland which seals the two each (2) 18 Gage Wires,Plus a grounding Wire. included With each E.I.M.B. Model: Electrical interlock Box With safety limit switch, wiring and Mounting bracket With locking knob. Special Latheguard Tube wiring Diagram. Dimensions of Rectangular box portion of E.I.M.B.: Approx. 6-5/8 X 2-3/8 X 1-5/8 inches (168mm x 60mm x 41.3mm) Model No. 17004., Top Mounting for flat Top of Headstock. All Shield Sizes. Note: Observing the lathe structure and taking a few Measurements makes Proper selection easy.

Manufacturer: Checkline Brand: Checkline

Materials used: steels, glass, thin plastics. Range in steel: 3/16" (.040" -6.0"), 1/4" (.040" - 6.0"), 1/2" (.050" - 19.99"). Wearface diamenter: 1/4", 3/8" or 5/8". Crystal diameter: 3/16", 1/4" or 1/2" 1/4" diameter, 5.0 MHz dual element transducer Alpha-Hi Damped, potted cable, top in

Manufacturer: Checkline Brand: Checkline

5mhz, 10mm Transducer for TI-45N and TI-40N Ultrasonic Thickness Gauges

Manufacturer: Checkline Brand: Checkline

1/4" diameter, 5.00 MHz Coating Probe For use with TI-CMX, TI-CMXDL and TI-CMXDLP

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 201-162

The Mitutoyo 201 series dial snap gauge is sized in inch units for Go/No Go (Go/NG) inspection of diameters of cylinders and shafts, to verify the workpiece is within tolerance limits. It can be fitted with a dial indicator that has a 3/8” stem diameter to measure deviation from a preset minimum tolerance (sold separately). The anvils of the snap gauge are made of carbide to help resist wear, and their front edges are chamfered to ease insertion of a workpiece between them for inspection. One anvil can be repositioned by turns of a knurled spindle up to 1” of positioning range, and a knurled, nut-type spindle lock provides secure locking of the measurement position. The fixed anvil has a retraction stroke to 0.078”. Snap gauges, also called gages, are precision measuring instruments used to verify that the dimension of a workpiece matches or falls within predefined tolerances. The instrument provides quick limit, also called Go/No Go (Go/NG), inspection by testing the fit of a workpiece to pass between an adjustable opening between anvils. A snap gauge may include a dial or electronic indicator to measure the deviation from the preset dimension. Snap gauges are typically used in manufacturing, machining, and mechanical engineering. Mitutoyo manufactures precision measuring tools, metrology equipment, and systems. The company was founded in Tokyo in 1934 and formed Mitutoyo America Corporation in 1963, which is headquartered in Aurora, IL.

Manufacturer: Checkline Brand: Checkline

Materials used: cast iron, plastics (polypropylene, polyethylene, etc.), fiberglass. Range in steel: 1/2" (.150" - 2.0") Wearface diamenter: 5/8" Crystal diameter: 1/2" 1/2" diameter, 1.00 MHz dual element transducer Composite potted cable, side in