|
|
-
3.5 of 5.0 with 48 Reviews
SALE PRICE: $715.00 1% OFF
Manufacturer: Mitutoyo America Corporation
Brand: Mitutoyo
Model: 209-904
Manufacturer: Mitutoyo America Corporation
Brand: Mitutoyo
Model: 209-904
Mitutoyo Digital Caliper Gage 209-904, Internal Measurement Type, .60-2.17In, .001In, 127mm Depth.
-
3.5 of 5.0 with 38 Reviews
SALE PRICE: $715.00 1% OFF
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 209-557
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 209-557
|
The Mitutoyo 209 series Digimatic internal tube thickness caliper gauge has a combination analog/digital LCD display and large measuring depth for taking inside dimension (ID) measurements of hole diameters, thickness of grooves or tubes, and other hard-to-reach internal dimensions. Depending on the model, these units may come with either ball contact points suitable for measuring internal wall thickness of tubes, or disc contact points suitable for measuring flat surfaces. The calipers have an Ingress Protection 67 (IP67) rating, which ensures that components are resistant to debris and to submersion in liquid under standard conditions for up to 30 minutes. At minimum, functions include zero-set, preset, automatic power off, inch/metric, and conversion data hold. An output port transmits results to a Mitutoyo miniprocessor or computer for statistical process control (SPC) through an interface cable (sold separately). The unit comes with, and is powered by, a single AA battery that lasts approximately 350 hours with continuous normal use. Calipers measure the distance between two opposing sides of an object. They make inside, outside, depth, or step measurements, according to their type. Calipers are commonly used in architecture, metalworking, mechanical engineering, and machining. The simplest calipers have two legs to mark the two points and require a ruler to take the measurement. More complex calipers use two sets of jaws instead of legs and have up to two graduated scales. Vernier, dial, and digital calipers give direct and accurate readings and are functionally identical, having a calibrated scale with a fixed jaw, and another jaw with a movable pointer that slides along the scale. The vernier caliper has a scale sliding parallel to the main scale for an additional, fractional reading to improve measurement precision. The dial caliper has a circular dial with a pointer on a toothed gear rack replacing the second vernier scale. As with the vernier, this second measurement is added to the reading from the m...
-
3.5 of 5.0 with 38 Reviews
SALE PRICE: $720.61 1% OFF
Manufacturer: Fred V. Fowler Company, Inc.
Brand: Fowler
Model: 52-255-312-0
Manufacturer: Fred V. Fowler Company, Inc.
Brand: Fowler
Model: 52-255-312-0
|
The Fowler Inch Series XT Holemike Bore Gauge has a ratchet stop for consistent measuring and non-removable anvils. This direct-measuring gauge uses a three-point contact system and tungsten carbide contact points above 0.5". Setting rings are included. Each gauge is individually serialized.Bore gauges measure holes, or bores, in a workpiece. They can measure the interior diameter of a hole at any depth, while internal micrometers can only measure to the depth of their teeth. Bore gauges are typically calibrated with a setting ring and come in two types: simple and direct-measuring. Simple bore gauges are used with a caliper to transfer the hole measurement, while the more complex gauges take the measurement directly, and display it through a vernier, dial, or digital display. Bore gauges have a two- or three-point contact, indicating how many points on the gauge head touch the inside of the bore. Two-point contacts are better at measuring ovality, while three-point contacts are used to measure lobing or triangular form error. Pistol-grip bore gauges are used for fast, single-handed operation with repeatable results from one operator to another. Bore gauges can also be used in special applications, such as measuring threads, spline pitch diameters, and deep bores.The Fred V. Fowler Company manufactures inspection and measurement instruments such as electronic indicators, calipers, bore gages, and digital scales. The company, founded in 1946, is headquartered in Newton, MA.
-
3.5 of 5.0 with 2 Reviews
SALE PRICE: $729.22
Manufacturer: Fred V. Fowler Company, Inc.
Brand: Fowler
Model: 54-175-024-0
Manufacturer: Fred V. Fowler Company, Inc.
Brand: Fowler
Model: 54-175-024-0
|
The Fowler Z-Height E chrome-plated electronic height gauge is precise to 0.0005" (0.01mm), and has a high-contrast LCD readout, a large, hand-operated feed wheel, a carbide-tipped scriber, and a positive lock. A hand-operated feed wheel raises and lowers the gauge on the beam with smooth, even travel, and is selectable for coarse or fine feed. The gauge has a hold function to freeze recordings on the 11mm display, as well as a zero setting function. A datum position recall function programs more than one zero point. Relative and absolute measuring functions allow measurements of the true size or comparison measurements of parts to a master. An incremental measuring function allows each reading to be taken from the previous reading. The measuring speed is 120" per second. The gauge has RS-232 output for data transfer. The included scriber, used to mark position on the workpiece, is carbide-tipped for hardness and durability. The gauge is powered by one CR 2032, 3V lithium battery (sold separately) that provides up to one year of normal use. The display flashes to indicate when battery replacement is needed. The gauge has a working environment temperature of 32 to 104 degrees F (0 to 40 degrees C) with a surrounding relative humidity of 80 percent. Storage and transport temperature is -4 to 158 degrees F (-20 to 70 degrees C). The satin chrome finish on the scales resists rust and is glare-free. The base is hardened, ground, and lapped for maximum flatness. The gauge comes with a molded case.Height gauges, sometimes referred to as gauges, are precision measuring instruments that travel on a vertical column (also called the beam) to measure and/or mark the vertical distance from the base of an object in fine units. The vertical position of the gauge and its attached pointer are changed by turning a calibrated screw, or one or more feed wheels. Recorded rotations are read from a scale, a dial, counters, and/or an electronic display. A screw clamp holds the pointer to the gauge. The pointer is typically sharpened to ...
-
3.5 of 5.0 with 37 Reviews
SALE PRICE: $753.11
Manufacturer: Starrett
Brand: Starrett
Model: 687M-2Z
Manufacturer: Starrett
Brand: Starrett
Model: 687M-2Z
Starrett Countersink Gauges are offered in three different angles so that the gauge sets on the angular side of the countersink, as opposed to a chamfer gauge which sets on the top edge of the chamfer. This gauge directly reads the large diameter of the countersink in 0.002" or 0.05 mm increments. A set master ring is furnished with each gauge for calibration and setting. Press the button on top of the indicator to firmly depress the gauge head into the countersink. When the gauge is removed, the indicator reading is held in place until the reset button is activated.
-
3.5 of 5.0 with 15 Reviews
SALE PRICE: $767.00
Manufacturer: INSIZE
Brand: INSIZE
Model: 3222-40
Manufacturer: INSIZE
Brand: INSIZE
Model: 3222-40
Tubular inside micrometer, 2-40", graduation 001".
-
3.5 of 5.0 with 31 Reviews
SALE PRICE: $775.00 1% OFF
Manufacturer: DeFelsko
Brand: DeFelsko
Manufacturer: DeFelsko
Brand: DeFelsko
The PosiTector 6000 FRS1 Coating Thickness Gauge Standard Model with Right Angle Probe for Ferrous Metal Substrates (0-60 mils/1500 um), complete kit is a simple and durable precision instrument that uses magnetic and eddy current principles to accurately measure coating thickness on both ferrous and non-ferrous metals. All Positector 6000 Coating Thickness Gauges are supplied complete with precision plastic shims, protective rubber holster with belt clip, 3 AAA batteries, instructions, wrist strap (built-in style only), nylon carrying case with shoulder strap, NIST Traceable Certificate of Calibration, two (2) year warranty.
-
3.5 of 5.0 with 41 Reviews
SALE PRICE: $816.04 7% OFF
Manufacturer: Hexagon Metrology, Inc.
Brand: Standard Gage
Model: 07734007
Manufacturer: Hexagon Metrology, Inc.
Brand: Standard Gage
Model: 07734007
Standard Gage IP67 digital scribing height gages provide great value. Available in 12 inch or 24 inch sizes, they feature Absolute and Relative modes, PRESET function, Keypad lock, RS data output, Auto-off and inch/metric readings.
-
3.5 of 5.0 with 15 Reviews
SALE PRICE: $895.00 9% OFF
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 139-179
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 139-179
|
The Mitutoyo 139 series tubular vernier inside micrometer includes a set of extension pipes with anvils for a diversified range of measurement measuring inside dimensions (ID) of cylinders, rings, and parallel surfaces. It has a vernier scale in inch units for taking precise ID measurements to 0.001â€, and a satin chrome rust- and glare-resistant finish. The micrometer head has a travel of 1†per revolution that helps provide quick positioning. The hollow, tubular extension pipes help provide light weight with rigidity. A locking clamp helps hold measurements in place. The micrometer and accessories come with a fitted case for storage.Micrometers are precision measuring instruments that use a calibrated screw to measure small distances. These measurements are translated into large rotations of the screw that are then able to be read from a scale or a dial. Micrometers are typically used in manufacturing, machining, and mechanical engineering. There are three types of micrometer: outside, inside, and depth. Outside micrometers may also be called micrometer calipers, and are used to measure the length, width, or outside diameter of an object. Inside micrometers are typically used to measure interior diameter, as in a hole. Depth micrometers measure the height, or depth, of any shape that has a step, groove, or slot.Mitutoyo manufactures precision measuring tools, metrology equipment, and systems. The company was founded in Tokyo in 1934 and formed Mitutoyo America Corporation in 1963, which is headquartered in Aurora, IL.
-
3.5 of 5.0 with 15 Reviews
SALE PRICE: $895.00 9% OFF
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 139-179
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 139-179
|
The Mitutoyo 139 series tubular vernier inside micrometer includes a set of extension pipes with anvils for a diversified range of measurement measuring inside dimensions (ID) of cylinders, rings, and parallel surfaces. It has a vernier scale in inch units for taking precise ID measurements to 0.001â€, and a satin chrome rust- and glare-resistant finish. The micrometer head has a travel of 1†per revolution that helps provide quick positioning. The hollow, tubular extension pipes help provide light weight with rigidity. A locking clamp helps hold measurements in place. The micrometer and accessories come with a fitted case for storage.Micrometers are precision measuring instruments that use a calibrated screw to measure small distances. These measurements are translated into large rotations of the screw that are then able to be read from a scale or a dial. Micrometers are typically used in manufacturing, machining, and mechanical engineering. There are three types of micrometer: outside, inside, and depth. Outside micrometers may also be called micrometer calipers, and are used to measure the length, width, or outside diameter of an object. Inside micrometers are typically used to measure interior diameter, as in a hole. Depth micrometers measure the height, or depth, of any shape that has a step, groove, or slot.Mitutoyo manufactures precision measuring tools, metrology equipment, and systems. The company was founded in Tokyo in 1934 and formed Mitutoyo America Corporation in 1963, which is headquartered in Aurora, IL.
Viewing Page 1451 of 1520
|
|