Indoor Air Quality Meters - Page 19

Manufacturer: Dwyer Instruments, Inc. Brand: Dwyer

Dwyer® Series CDTR Carbon Dioxide, Relative Humidity and Temperature Transmitters reduce the number of sensors mounted on a wall or in a duct. By combining CO2, RH, and temperature in one device, system integrators are able to lower installation time of mounting multiple housings, while lowering material cost at the same time. Even with the three sensors combined into a single unit, replacement cost is not increased due to the pluggable nature of the humidity sensor, which allows it or the temperature to be replaced at a fraction of the cost of a new CO2 transmitter. Like our popular Series CDT Carbon Dioxide Transmitter, a single-beam dual-wavelength non-dispersive infrared (NDIR) sensor is used to automatically correct the measurement in both occupied* and unoccupied buildings against light source aging effects. The single-beam dual-wavelength sensor technology provides the highest level of accuracy compared to Automatic Baseline Correction methods which can unintentionally shift the calibration based on CO2 levels and barometric pressure conditions. In order to achieve a higher level of accuracy, the Series CDTR also includes digital barometric pressure adjustment and the ability to field-calibrate the sensor. Universal outputs for both carbon dioxide and relative humidity allow users to select the transmitter output to be 4 to 20 mA, 0 to 5 VDC, or 0 to 10 VDC to work with virtually any building management controller. Additionally, passive thermistor or RTD sensor can be ordered for a temperature output. Push buttons are standard on all configurations of the transmitters for access to the menu structure, but wall mount configurations can be ordered without the buttons.

Manufacturer: Dwyer Instruments, Inc. Brand: Dwyer

Dwyer® Series CDTR Carbon Dioxide, Relative Humidity and Temperature Transmitters reduce the number of sensors mounted on a wall or in a duct. By combining CO2, RH, and temperature in one device, system integrators are able to lower installation time of mounting multiple housings, while lowering material cost at the same time. Even with the three sensors combined into a single unit, replacement cost is not increased due to the pluggable nature of the humidity sensor, which allows it or the temperature to be replaced at a fraction of the cost of a new CO2 transmitter. Like our popular Series CDT Carbon Dioxide Transmitter, a single-beam dual-wavelength non-dispersive infrared (NDIR) sensor is used to automatically correct the measurement in both occupied* and unoccupied buildings against light source aging effects. The single-beam dual-wavelength sensor technology provides the highest level of accuracy compared to Automatic Baseline Correction methods which can unintentionally shift the calibration based on CO2 levels and barometric pressure conditions. In order to achieve a higher level of accuracy, the Series CDTR also includes digital barometric pressure adjustment and the ability to field-calibrate the sensor. Universal outputs for both carbon dioxide and relative humidity allow users to select the transmitter output to be 4 to 20 mA, 0 to 5 VDC, or 0 to 10 VDC to work with virtually any building management controller. Additionally, passive thermistor or RTD sensor can be ordered for a temperature output. Push buttons are standard on all configurations of the transmitters for access to the menu structure, but wall mount configurations can be ordered without the buttons.

Manufacturer: Dwyer Instruments, Inc. Brand: Dwyer

Dwyer® Series CDTR Carbon Dioxide, Relative Humidity and Temperature Transmitters reduce the number of sensors mounted on a wall or in a duct. By combining CO2, RH, and temperature in one device, system integrators are able to lower installation time of mounting multiple housings, while lowering material cost at the same time. Even with the three sensors combined into a single unit, replacement cost is not increased due to the pluggable nature of the humidity sensor, which allows it or the temperature to be replaced at a fraction of the cost of a new CO2 transmitter. Like our popular Series CDT Carbon Dioxide Transmitter, a single-beam dual-wavelength non-dispersive infrared (NDIR) sensor is used to automatically correct the measurement in both occupied* and unoccupied buildings against light source aging effects. The single-beam dual-wavelength sensor technology provides the highest level of accuracy compared to Automatic Baseline Correction methods which can unintentionally shift the calibration based on CO2 levels and barometric pressure conditions. In order to achieve a higher level of accuracy, the Series CDTR also includes digital barometric pressure adjustment and the ability to field-calibrate the sensor. Universal outputs for both carbon dioxide and relative humidity allow users to select the transmitter output to be 4 to 20 mA, 0 to 5 VDC, or 0 to 10 VDC to work with virtually any building management controller. Additionally, passive thermistor or RTD sensor can be ordered for a temperature output. Push buttons are standard on all configurations of the transmitters for access to the menu structure, but wall mount configurations can be ordered without the buttons.

Manufacturer: Testo AG Brand: Testo Model: 0393 0002

Testo O2 measuring cell for 330G LL flue gas promo set.

Manufacturer: Testo Brand: Testo Model: 0563 0003 Color: Multicolored

Testo 0563 0003 Smart and Wireless VAC Probe Kit The testo VAC Smart Probe Set provides a combination of four instruments needed to test and balance a multioutlet ventilation system. Two types of anememoters give you the capacity to measure in-duct air flow and the flow from each vent. Using an IR temperature probe for surface temperatures will show you motor and electrical equipment conditions and an easy check of each outlet. The thermohygrometer will provide an assessment of the humidity and dewpoint concerns throughout the system. Users can remotely read the measurements from multiple probes by using the testo Smart Probes App. The kit comes with a handy case at a great value. The testo Smart Probes App is a powerful and easy-to-use tool. It allows you to remotely read measurements from up to six (6) Smart Probes and easily document/report the results. Automatic calculations make it a snap! All measurement data is displayed as instrument readings, tables, or graphs. The measurements can be quickly saved as PDF or Excel files. The App creates custom reports which can be saved and/or shared by email. All your data can be stored and retrieved saving you hours of time consuming paperwork!   Smart Probes - VAC kit testo Smart Probes VAC set for servicing ventilation and air conditioning systems. Consists of: testo 405i, testo 410i, testo 605i, testo 805i, testo Smart Case (VAC), batteries, and certificate of calibration

Manufacturer: Generic Brand: Tenmars

HEAT Stress WBGT Meter TM-188D FEATURES: - Quick-response capacitance sensor, accurate measurement for wet bulb globe temperature(WBGT)black globe temperature(TG), humidity(%RH), air temperature(TA), wet bulb(WET) and dew point(DEW). - Max/Min and data hold. - Low battery indication. - LCD display with LED backlight. - Viewing data records. - Switch the temperature unit to ℃ or ℉. - Brass black ball in 50mm diameter. - WBGT alarm setting. - Auto power off with disable function. - Data logging capacity: 12000 records, USB PC serial interface (TM-188D). - Sampling interval: Max 24 hours; Min 1 Second (TM-188D SPECIFICATIONS: Part Number: Tenmars TM-188D Item Weight: 4.4 pounds Product Dimensions : 14.8 x 9.3 x 4.9 inches Item model number: Tenmars TM-188D Item Package Quantity: 1 Batteries Included? :No Batteries Required? :No - Dimension : 300 x 70 x 50mm (L x W x H) - Weight : 220g. (Without batteries). - Power supply : 006P 9V,or AC100~240V DC 9V/ 0.5A(9mm). - Battery life : 200 hours. - Operating Temperature & Humidity :0°C to +50°C. - Storage temperature & humidity : -10°C to +50°C . - Data output :USB PC serial interface, 12000 records. (TM-188D) - LCD: 52mm(W)x36mm(L) monochrome LCD and backlight. - Standard accessories: 006P 9V battery x1, User's manual x 1, Carrying x1

Manufacturer: UEI Test Instruments Brand: UEi Test Instruments Model: DMEG3

Large digital display shows the test function and measured value - 600V AC measurement capability - Insulation resistance ranges 0 - 2000MΩvThree test-voltage ranges (250, 500, 1000V DC) - Live circuit warning light - Fuse protected - Precision resistance 0.01Ω with audible continuity - 200 mA short-circuit continuity test current for high accuracy - Precision, low resistance test leads (1000 Volt CAT III rated).

Manufacturer: Test Products International, Inc Brand: TPI Model: A127

The TPI A127 is a kit containing a strap with an attached magnet and hooks for hanging an air quality meter. This strap is for use with TPI 1008A IAQ and 1010A IAQ meters (sold separately). The hooks are constructed of coated steel for corrosion-resistance. This kit enables a meter to be attached to a metal surface via the magnetic strap or hung using the included hooks and used hands free.Indoor air quality (IAQ) meters test air for temperature, humidity, dew point, air flow, velocity, carbon monoxide (CO), and carbon dioxide (CO2) levels. IAQ meters may contain particle counters to measure levels of mold, viruses, and bacteria in the air. Test Products International (TPI) manufactures test and measurement equipment such as oscilloscopes, manometers, multimeters, and test leads. The company, founded in 1997, is headquartered in Beaverton, OR.

Manufacturer: Hakko Brand: Hakko Model: 393-1

Trackable Shipping (Standard and Expedited)

Manufacturer: UEI Test Instruments Brand: UEi Test Instruments Model: DL479 Color: Multicolored

AC 600A True RMS HVAC/R Clamp Meter.