Amprobe ACD-41PQ 1000A Power Quality Clamp Meter with Temperature

The Amprobe ACD-41PQ digital clamp meter is true RMS (root mean square) sensing, auto-ranging multimeter for measuring current, voltage, resistance, frequency, temperature, harmonics, power factor, and real, reactive, and apparent power in industrial electrical testing applications. It has a clamp that measures alternating current (AC) to 1,000 amp. The meter comes with detachable test leads that measure direct current (DC) voltage and AC voltage to 600 volts (V), resistance to 1,000 ohms, and frequency to 500 hertz (Hz). The clamp has two jaws that can close around an electrical conductor up to 1.77" (45 mm) in diameter to measure current without touching or interrupting the circuit. The meter comes with a K-type thermocouple probe for measuring temperature. Power factor, real power, reactive power, and apparent power readings provide data on the power efficiency of an electrical system. The meter measures fundamental total harmonic distortion (THD) and individual harmonics, which can degrade the quality of the power being supplied by the system. Automatic detection mode selects voltage or current function based on input. The peak hold reading displays the maximum measurement of a current or voltage surge. An audible continuity sensor confirms that the circuit conducts electricity. The hold function keeps the reading on the display, even after the meter is disconnected. The backlit liquid crystal display (LCD) is visible in low light. The unit automatically turns off after 17 minutes of non-use to conserve battery life, and a low-battery indicator signals when the meter's batteries need to be replaced. A finger guard on the body of the meter helps protect fingers from shock.

This true RMS (root mean square) sensing meter provides accurate readings when measuring linear loads, such as standard induction motors and incandescent lights, where the current or voltage has a sinusoidal waveform, or non-linear loads, such as electronic devices or motors, where the current or voltage has a sinusoidal non-sinusoidal waveform. This auto-ranging meter automatically selects the correct operating range for the property being measured. The meter has a 4,000 count resolution for current measurements, a 6,000 count resolution for voltage measurements, and a 10,000 count resolution for power, ohm, and frequency measurements, meaning it can display up to 3,999 (3-3/4 digits), 5,999 (3-5/6 digits), and 9,999 units (4 digits), respectively, before the operating range needs to be changed. It meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category III installations up to 600V, which covers items used with enclosed building circuit installations (service panel parts, branch circuits, and fixed installations that are connected directly to a building's AC power supply). The unit comes with a soft vinyl carrying case.

Specifications

H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.

Clamp meters (also called clamp-on meters) measure electrical current without cutting through wires or touching or interrupting the electrical circuit. Available in handheld or benchtop models, clamp meters diagnose problems in electrical equipment, wiring, and power supplies. The meter's current clamp has two jaws that fit around a conductor to take measurements. All clamp meters test for current. Some come with test leads and inputs for measuring voltage, capacitance, and resistance. They display information either in analog or digital form. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltages determine meter choice. Safety ratings are based on the International Electrotechnical Commission's (IEC) standards for low-voltage test equipment. IEC 61010 delineates four overvoltage installation categories. In general, a meter with a category IV rating will provide more protection against transient voltages than a meter with a lower category rating.

Amprobe manufactures electrical testing equipment for commercial, industrial, and home use. The company was founded in 1948 and is headquartered in Everett, WA.

What’s in the Box?

• ACD-41PQ TRMS digital clamp meter
• (1) Set test leads
• (1) K-type thermocouple probe
• (2) 1.5V AAA batteries (installed)
• Carrying case with belt loop
• Instructions