Circuit Tracers & Analyzers - Page 19

Manufacturer: Gems Sensors Brand: Warrick Model: 16MA1M0

Designed for either differential or single-level service. U.L. “Motor Controller” listing, 8 pin socket with screw-type connections make the unit easy to install and service. Sensitivity of up to 1 million ohm/cm.

Manufacturer: Gems Sensors Brand: Warrick Model: 26NMC1B0

Series 26M is designed for low-water cutoff protection. This control meets CSD1 requirements for boiler low water cutoff. Series 26M features powered contacts. If non-powered contacts are required, request information on Series 26NM.

Manufacturer: Psiber Data Systems Brand: Psiber Data Model: MM-A22DN

Psiber Multimode SFP Interface is a module for use only with the LanExpert LE85M and LE85S. Psiber accessories and parts.

Manufacturer: Psiber Data Systems Brand: Psiber Data Model: LE85M

The LanExpert 85 network analyzer provides expert assistance for all tiers of LAN installers, technicians and managers working with either copper or fiber media. The Inline Mode allows users to non-intrusively monitor network traffic (10/100/1000BaseTX) to identify protocols, port usage, VoIP statistics and network utilization. The LANEXPERT can capture and store up to 10,000 packets with user defined filters for detailed analysis in the field or downloaded over the network or to a USB flash drive. Using either RJ-45 port, tests including Ping, Link, Trace Route, DHCP and Discovery are used to quickly identify network problems The LANEXPERT can generate up to 100% traffic loading with control of packet rate and size to demonstrate network performance at various traffic levels. Additionally, a stress test that generates traffic and measures performance metrics, in accordance with RFC 2544, is also provided. The stress test can be conducted using the two independent ports on a single unit or used with a second unit located remotely on a network. PoE tests include voltage and inline current measurement to determine the actual power used by a powered device. The LANEXPERT also test cables for shorts, opens, split pairs, reversed pairs, measures cable length and generates tones for cable tracing. The LANEXPERT is a comprehensive network analyzer that allows users to deliver robust and reliable network services with a single test device. LAN installers, technicians, managers and service providers can now get expert network help at an affordable price.

Manufacturer: Foxboro Brand: Foxboro

Foxboro Electrochemical Analyzer 873Ec-Aipfgz (9420)

Manufacturer: Tasco Brand: Tasco

Features Set includes carry case, up to 42 clamps and all accessories. Easy to use with no knobs of switches to adjust. Determines which breakers are serving specific branches in seconds. Identifies lines on any electrical wiring system. Eliminates equipment downtime because circuits can be tested with or without power. Saves valuable time and only requires one operator. Microprocessor based digital signal for utmost accuracy Locates up to 42 branches concurrently Made in U.S.A. 2 Year Warranty Download Manual The Circuit Mapper System The Circuit Mapper is the first device of its kind that maps branch circuits of wiring systems concurrently with a single transmitter and receiver. Traditional methods of identifying circuit breakers and wiring are inefficient and expensive, often requiring two people to perform. With sensitive electronic equipment, simply turning breakers off and on is no longer a viable option. Even modern circuit tracers typically trace only one branch circuit at a time. The Circuit Mapper transmitter connects to lines at the panel rather than at the end of the branch circuit. The receiver displays the corresponding circuit number through digital signal processing, with or without direct electrical contact, so you know exactly which breaker is connected to each transmitter lead. There is no time wasted comparing signals or looking for the strongest signal. Using the Circuit Mapper system will greatly reduce man-hours spent when locating branch connections of electrical circuits. How It Works Each of the clamps connected from the transmitter around a conductive circuit induce a coded signal modulated at 166KHz. There is a unique code for each of the branch circuits. The receiver is able to measure the sinal on a conductor when the probe is inserted to the outlet.

Manufacturer: Storehouse Brand: Storehouse

Set comes organized in PVC tray Includes: (6) 2" alligator clips, (6) 1-1/2" alligator clips, (10) mini alligator clips, (2) 30 amp charging clips, (2) 25 amp charging clips, (2) 10 amp charging clips

Manufacturer: Extech Instruments Brand: Extech Model: RT30 Color: Multicolor

EXTECH Wireless AC Circuit A must-have tool for electricians, do-it-yourselfers, contractors, kitchen, bath and lighting installers, and handymen, the Extech RT30 Wireless Remote AC Circuit Identifier enables you to identify circuit breakers, wiring, switched lines, AC outlets and, light fixtures without cutting into any wires--and without a helper. The RT30's wireless transmitter (view larger). RT30 Wireless Remote AC Circuit IdentifierAt a Glance: Easily identify the correct circuit powering the cable to be spliced or repaired Eliminates the need for an assistant or back-and-forth trips for confirmation Built-in light sensor can identify remote lighting circuits Powered by four AAA batteries One-year limited warranty This versatile tool uses a pager-sized, non-contact voltage detector transmitter that clamps onto wiring mid-run and transmits a "voltage present" signal to a pocket-sized receiver carried by the user. Clamped onto a live wire, the transmitter signals the user at the breaker panel with LED and audible alerts on the receiver (up to 100-meter range). The alerts stop when the correct circuit breaker is switched and work can then be performed safely. The RT30 wirelessly identifies the correct Circuit Breaker controlling remote mid run AC wiring (using the included non-contact transmitter); lighting circuits (using the included built in light sensor), and AC outlets (using the included AC outlet extender). A compact external clamp-style non-contact voltage (NCV) probe can be used for wires that are hard-to-reach, or within a bundle. For inaccessible circuit wiring, a useful lighting circuit identification function uses a light sensor to indicate lighting changes in a room caused by the user remotely opening a circuit breaker and turning off a light on the circuit. An optional AC outlet extender can also be used to identify circuits by outlets. The RT30's clamp-style probe accessory is ideal for wires that are hard to isolate or reach. The RT30's remote is ...

Manufacturer: T3 Innovation Brand: T3 Innovation Model: CC200

Dark unpowered coax systems give no clue as to their design, condition or configuration. The new Coax Clarifier by T3 Innovation makes it simple and easy to discern the layout of a coax network, locate faultson individual cable runs, identify remotes through splitters, and determine cable run lengths. In addition, separate wiremapping sets allows a technician to map out the entire coax system and measure the quality and characterization of the overall network for carrying services, such as high grade video, surveillance data and HD programming.

Manufacturer: Amprobe Brand: Amprobe Model: 4416052

The Amprobe AT-4001-A advanced wire tracer is a circuit tracer used to locate and trace energized and non-energized wires, breakers, neutrals, and grounds to identify shorts, ground faults, and broken wires. The unit includes a universal transmitter that automatically switches to work with energized or non-energized systems. The transmitter can be manually set to low, medium, or high sensitivity for use on a variety of different circuit types. The unit comes with a soft carrying case to protect the instrument. The tracer is compatible with 9 to 300V alternating current (AC) or direct current (DC) circuits and has an operating frequency of 32.786kHz. The receiver is not position sensitive, so it does not need to be rotated to provide accurate readings. The receiver indicates the location of a wire with a series of ten LEDs and the transmitter indicates results on an LCD display. The transmitter and the receiver are each powered by one 9V battery. The AT-4001-A is designed for use by electricians and electrical contractors. Specifications Power supply for transmitter: (1) 9V battery (included) Power supply for receiver12/30/201312/30/2013: (1) 9V battery (included) AC/DC voltage range: 9 to 300V Amprobe manufactures electrical testing equipment for commercial, industrial, and home use. The company was founded in 1948 and is headquartered in Everett, WA. What’s in the Box? AT-4001-A Advanced Wire Tracer (1) T-4000-A Transmitter (1) R-4000 CON Receiver (1) C2901 110V Pigtail-banana plug cord set (1) C2902 Alligator clips-banana plug cord set (1) MTL-G 25 ft. grounding test lead (1) VRC-320 Alligator clip for ground lead (1) SV-1000 Soft carrying case (1) 9V battery Instructions