Gage Blocks - Page 25

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611681-531

The Mitutoyo grade 0 rectangular gage block is made of steel, has its nominal length engraved in metric [millimeter (mm)] units, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 0 gage block is commonly used in workshop and inspection applications to calibrate and inspect mechanical parts and tools, to verify the accuracy of plug and snap gages, and to set electronic measuring devices. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear resistance. This gage block has a rectangular base for accurate wringing. Nominal length is measured in metric [millimeter (mm)] units, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 9 millimeters. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment and to standardize the measurement of length in ...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 614107-521

The Mitutoyo grade 00 square gage block is made of steel, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 00 gage block is commonly used within a controlled environment as a reference standard for setting high-precision measuring equipment, to calibrate low-grade gage blocks, and to inspect the accuracy of gages, mechanical parts, and tools. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear-resistance. This gage block has a square base for accurate wringing, to attain a height reference standard, and for the ability to make a dedicated inspection jig. Nominal length is measured in inches, and indicated on the block with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.95 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibr...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 616303-521

The Mitutoyo grade 00 square gage block is made of ceramic, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 00 gage block is commonly used within a controlled environment as a reference standard for setting high-precision measuring equipment, to calibrate low-grade gage blocks, and to inspect the accuracy of gages, mechanical parts, and tools. It is made of ceramic which resists corrosion, abrasion, and burrs, can withstand high temperatures without melting (high thermal expansion resistance), and provides dimensional stability. This gage block has a square base for accurate wringing, to attain a height reference standard, and for the ability to make a dedicated inspection jig. Nominal length is measured in inches, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.355 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611311-531

The Mitutoyo grade 0 rectangular gage block is made of steel, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 0 gage block is commonly used in workshop and inspection applications to calibrate and inspect mechanical parts and tools, to verify the accuracy of plug and snap gages, and to set electronic measuring devices. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear resistance. This gage block has a rectangular base for accurate wringing. Nominal length is measured in inches, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.355 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment and to standardize the measurement of length in manufacturing industries. They are commonly made o...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 613217-541

The Mitutoyo grade AS-1 rectangular gage block is made of ceramic, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. The grade AS-1 gage block is commonly used for workshop and inspection applications to calibrate fixtures and precision instruments, to inspect a variety of tools such as mounting tools, cutters, fixtures, and mechanical parts, and for manufacturing gage applications. It is made of ceramic which resists corrosion, abrasion, and burrs, withstands high temperatures without melting (high thermal expansion resistance), and provides dimensional stability. This gage block has a rectangular base for accurate wringing. Nominal length is measured in inches, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.355 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 614623-531

The Mitutoyo grade 0 square gage block is made of steel, has its nominal length engraved in metric [millimeter (mm)] units, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 0 gage block is commonly used in workshop and inspection applications to calibrate and inspect mechanical parts and tools, to verify the accuracy of plug and snap gages, and to set electronic measuring devices. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear resistance. This gage block has a square base for accurate wringing, to attain a height reference standard, and for the ability to make a dedicated inspection jig. Nominal length is measured in metric [millimeter (mm)] units, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 24.1 millimeters. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 614673-541

The Mitutoyo grade AS-1 square gage block is made of steel, has its nominal length engraved in metric [millimeter (mm)] units, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. The grade AS-1 gage block is commonly used for workshop and inspection applications to calibrate fixtures and precision instruments, to inspect a variety of tools such as mounting tools, cutters, fixtures, and mechanical parts, and for manufacturing gage applications. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear-resistance. This gage block has a square base for accurate wringing, to attain a height reference standard, and for the ability to make a dedicated inspection jig. Nominal length is measured in metric [millimeter (mm)] units, and is indicated on the block with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 24.1 millimeters. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 616118-521

The Mitutoyo grade 00 square gage block is made of ceramic, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 00 gage block is commonly used within a controlled environment as a reference standard for setting high-precision measuring equipment, to calibrate low-grade gage blocks, and to inspect the accuracy of gages, mechanical parts, and tools. It is made of ceramic which resists corrosion, abrasion, and burrs, can withstand high temperatures without melting (high thermal expansion resistance), and provides dimensional stability. This gage block has a square base for accurate wringing, to attain a height reference standard, and for the ability to make a dedicated inspection jig. Nominal length is measured in inches, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.355 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 614205-531

This Mitutoyo grade 0 square gage block is made of steel, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 0 gage block is commonly used in workshop and inspection applications to calibrate and inspect mechanical parts and tools, to verify the accuracy of plug and snap gages, and to set electronic measuring devices. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear resistance. This gage block has a square base for accurate wringing, to attain a height reference standard, and for the ability to make a dedicated inspection jig. Nominal length is measured in inches, and indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.95 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment and to standardi...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 616116-521

The Mitutoyo grade 00 square gage block is made of ceramic, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 00 gage block is commonly used within a controlled environment as a reference standard for setting high-precision measuring equipment, to calibrate low-grade gage blocks, and to inspect the accuracy of gages, mechanical parts, and tools. It is made of ceramic which resists corrosion, abrasion, and burrs, can withstand high temperatures without melting (high thermal expansion resistance), and provides dimensional stability. This gage block has a square base for accurate wringing, to attain a height reference standard, and for the ability to make a dedicated inspection jig. Nominal length is measured in inches, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.355 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and...