Thermal Imagers - Page 37

Manufacturer: NETCNA Brand: NETCNA

This 3x Magnifier Lens from N-Vision is a germanium afocal lens that is compatible with select thermal imaging systems. This powerful optic extends the imager's range of detection/recognition, and it can be used without modifying the system's thermal core.

Manufacturer: HT Instruments Brand: HT Instruments

HT Instruments MPP300 Adapter for PV Testing on Multistring Installation The innovative accessory MPP300, used together with SOLAR300N or SOLAR I-V, allows measuring and recording the main parameters which characterize single-phase and three-phase, single-string and multi-string (up to three strings) photovoltaic systems. MPP300 is perfect for use in systems with three-MPPT three-phase inverter and in three-phase systems provided with three single-phase inverters. MPP300 is provided with a practical anti-shock "field" case, lightweight and small in size. The front panel carries the LEDs for operating information and the DC and AC inputs for upstream and downstream connection of the inverter(s). MPP300 interfaces with SOLAR300N via USB connection and SOLAR I-V via wireless connection. SOLAR300N and SOLAR I-V are used for MPP300 settings, to start/stop recording electrical and environmental parameters and to enable the download of the recorded values.  The distance between the photovoltaic modules and the inverter is often considerable, and this forces the operator to carry out measurements in different places at the same time. Therefore, it would be necessary to lay long connection cables between the environmental probes and the instrument. These cables could hamper the operator's movements, be a hindrance, etc. This kind of connection is therefore not acceptable. In case of photovoltaic installations on buildings, the so-called photovoltaic roofs, in addition to the problem of the distance between modules and inverter, the presence of floors, of reinforced concrete or metal structures, etc. must be taken into consideration. These structures would make a possible (wireless) radio connection between the environmental probes and the instrument impossible, because of signal attenuation

Manufacturer: HT Instruments Brand: HT Instruments

MACROTESTG2 Insulation Resistance, Ground Resistance and Bonding Continuity Tester   KitMacrotestG2 is the perfect and complete solution to measure Earth resistance, Insulation, ground bond continuity and single phase power quality.     One instrument for all electrical safety tests according to IEC/EN61557-1. Earth resistance with 2- or 3-pole volt-ampere method in TT, TN and IT systems, non-trip earth loop impedance measurement. Measurement of electrical parameters in single phase installations (V, A ,W,VAR,VA, PF) Continuity measurement of protective conductors. Soil resistivity. Insulation resistance measurement. Stackless earth ground resistance measurement with T2100 (optional).   Earth Ground Resistance The Macrotest Series easily measures earth ground (2 and 3 Point Method) and soil resistivity (4 Point Method) with an easy to understand graphical user interface and color touchscreen. The Macrotest Series easily measures earth ground (2 and 3 Point Method) and soil resistivity (4 Point Method) with an easy to understand graphical user interface and color touchscreen. The meter can store internally up to 999 measurements. The included software enables easy data transfer to a computer, tablet or phone via built-in Wi-Fi or USB connection where it can be archived or used to generate reports. The HTAnalysis application allows users, in real time, to view, analyze, upload and share measurements on the HT Cloud. This is a free app that is available to all. The Macrotest Series provides a complete set of easy to use measurements. The Macrotest Series utilizes the three point test (fall of potential), which measures earth ground resistance as required by equipment manufacturer specifications and as mandated by national code requirements for proper grounding

Manufacturer: FLIR Commercial Systems Brand: FLIR Model: T420

Manufacturer: TPI Brand: TPI

TPI 343/C1 Dual Input K-Type Thermocouple Thermometer with Field Calibration with two GK11M, A304, A340 soft pouch (For High Temp. over 400 F) TPI contact temperature testers are accurate, reliable, and built to last. Model 343 can be auto field calibrated to system accuracy (tester plus probe) of +/- 1°F in less than 10 seconds in ice water.   AUTO FIELD CALIBRATION Perform ice bath calibration to achieve ±1°F system accuracy within the 30°F to 120°F temperature range. Calibration is an easy two-step process performed with instrument keypad, no additional tools needed. Field calibration for thermometers TPI 343 FIELD CALIBRATION  The 343 has the ability to be field calibrated. Accuracy of +/-1°F within the 30°F to 120°F range can be achieved by performing an ice bath calibration. The temperature of an ice bath is approximately 32°F (0°C). Fill a plastic or metal container with crushed ice and add clean water to a depth of at least 4 inches. Stir the ice and water for 2 to 3 minutes prior to performing calibration to ensure the water is completely chilled. Make certain there is plenty of ice in the mixture and always use clean water. Distilled water works well. 1. Step-by-Step Procedures Connect both temperature probes to the 343. Press and hold down the MIN/MAX and HOLD buttons and turn the 343 on. CALF will be displayed and the 343 will enter calibration mode and begin cycling between T1 and T2. Insert the probes into the ice bath and allow the readings to stabilize. Once the reading on both inputs has stabilized, press the HOLD button. SAVE will be displayed and calibration is complete.

Manufacturer: Fluke Brand: Fluke

10.25" X 6.5" X 3.4" Hard Plastic Exterior Pick and Pack Foam Interior Convenient Carrying Handle   Pick & Pack Foam The HD-76 has been designed to fit a wide variety of items securely. In order to accommodate this, we have designed this case with pick & pack foam. This easy to customize Pick and Pack foam creates a snug and safe place for any contents. Foam can also be reinserted in case you ever need to change the case configuration. Versatility Give real protection to your tools. The IWH HD-76 offers convenience and expedience, merging form with function. This easy carrying case adds professionalism at an affordable cost. It provides enough space for most devices including accessories.

Manufacturer: Iris Brand: Iris

NightWatch Controller

Manufacturer: XARA Brand: XARA Model: 1190

Specifications : Display:2.4inch color display; Resolution:60*60; Total pixel:3600; FOV/Shortest focal length:20°x20°/0.5m; Thermal sensitivity:0.15°C; Measuring mode: Infrared focal plane measuring temperature; Temperature range:-20C-300C(-4F-572F); Measuring accuracy:±2C; Wavelength range:8-14μm; Image frequency:8HZ; Emissivity:0.1-1.0/Adjustable; Focus mode: Fixed; Palette: Iron color,rainbow,black and white; Set control: Unit Adjustment/Language/Date Time Format/automatic shut down; Battery type: 4*AA battery ( not included ) ; Adapter voltage:DV 5V output ; Operating temperature: 0C-50C; Storage temperature:-40C-70C; Humidity :

Manufacturer: FLIR Brand: FLIR Model: TG54-NIST

The TG54-NIST Spot IR (Infrared) Thermometer provides non-contact surface temperature readings so you can quickly and easily take measurements in places that are out of reach. Providing a distance-to-spot ratio of 24:1, the TG54-NIST can measure smaller targets from a safer distance. New mode options give you control to view your current reading and last two temperature readings simultaneously. The TG54-NIST is built with a color screen that makes it easy to navigate and select settings, plus adds visibility and efficiency to the advanced feature set. The TG54-NIST is your go-to, pocket-sized device for efficient temperature measurement. Includes wrist strap lanyard, quick start guide, user manual (CD), Certificate Traceable to NIST and 3 x AAA batteries.

Manufacturer: upHere Brand: upHere

"upHere IR Thermal Imager Good tool searching for abnormal heat source at home. Over-heated electronic devices and leakage of water can both be easily detected. Testing many of our electrical appliance products' temperature. locating termites or any other insect which you don`t hope them exist in your home. Product Description Display Screen: 2.4"" Full angle HD IR Image Resolution: 60 x 60 , 3600 pixels Thermal Sensitivity:0.15°C Temperature Accuracy:+/- 2 % or +/- 2 °C Visible Image Resolution:0.3 mega pixels Image Capturing Frequency:6 Hz Temperature Range: -20 to 300 °C"