Pressure Gauges - Page 75

Manufacturer: Dwyer Instruments Brand: Dwyer Model: 252-AF

Dwyer Durablock Series 250-AF Gages are precision machined 1" thick solid acrylic plastic, virtually unbreakable and free of distortion. The fluid bore is precision drilled to ±.0002" to assure life long accuracy. A glass spirit level is built into the body and encapsulated to prevent damage or tampering. The scale is mirror polished chrome plated brass to assure parallax free reading by alignment of the meniscus with its reflection. Safety traps are incorporated in the body to prevent loss of fluid due to pressure surges. Red and green signal flags indicate clearly when a filter change is necessary. Gages are suitable for use in ambient temperatures of -20 to 150°F. Connection fittings are positively sealed by "O" rings but easily removed for zeroing or addition of fluid. Furnished complete with instructions.

Manufacturer: Fluke Corporation Brand: Fluke Model: I3000S FLEX-24

The i3000s Flex is an ac current clamp utilizing the Rogowski principle. It can be used to measure currents up to 3000 A when used in conjunction with oscilloscopes, recorders or data loggers. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas. Three ranges: 30A, 300A and 3000A, 1, 10 or 100 mV/A output. Ideal for current measurement on thick and hard to reach conductors without breaking the circuit. Maximum conductor diameter 178mm. CAT III 600V safety rating. Output sensitivity (AC-coupled): 100 mV, 10 mV, 1 mV per A. Load impedance: 100 kilo ohm minimum. Accuracy at +25 degree C: +/-1 percent of range (45 Hz to 65 Hz). Linearity 10 to 100 percent of range: +/-0.2 percent of reading. Noise: 8 mV AC rms (30 A), 2 mV AC rms (300A, 3000A). Frequency range: 10 Hz to 50 kHz (-3 dB). Phase error: less than +/-1 degree (45 Hz to 65 Hz), +/-10 degree (at 20 kHz). Position sensitivity with cable greater than 25 mm from the coupling: +/-2 percent of range. External field with cable greater than 200mm from the head: +/-1 percent of range. Power supply: 2 x AA/MN 1500/LR6 Alkaline, 400 hours, low battery indicator or dedicated external power supply. Temperature Coefficient: +/-0.08 percent of reading per degree C. Working voltage: 600V AC rms or DC. Head circumference: 610mm. Head cable diameter: 14.3mm. Head bend radius: 38.1mm. Cable length (head to electronics): 2m. Output connection: 0.5m cable terminated with safety BNC connector. Supplied with 4mm safety plug adapter. Operating temperature range: -20 to +90 degree C (-4 to 190 degree F) (head), -20 to +85 degree C (-4 to 185 degree F) (electronics). Storage temperature range: -40 to +105 degree C (-40 to 221 degree F) (head), -20 to +85 degree C (-4 to 185 degree F) (electronics). Operating humidity: 15 to 85 percent (non-condensing).

Manufacturer: MANOTHERM Inc Brand: MANOTHERM

MANOTHERM Industrial Pressure Gauges Model P131 Case and bezel: Stainless steel 304 case, crimped bezel ring, corrosion resistant Dial Size: , 2.5" (63 mm) Connection size: 1/4" NPT-Male Ingress Protection: IP65 for protection against solid objects, including dust or liquids. Dial: White aluminum Pointer: Aluminum, anodized black Window: Polycarbonate for high impact resistance Measuring Range: Single psi scale or a dual scale of psi/kPa, psi/bar, Hg. vacuum/kPa, or Hg. vacuum/bar Operating temperature : -4 to 150 degrees F (-20 to 65 degrees C). Application: suitable for pumps, compressors, hydraulic presses, machinery, pneumatic equipment, and motors in harsh environments. MANOTHERM Inc. manufactures pressure gauges, thermometers, diaphragm seals, instrument manifolds and valves. The company founded in USA.

Manufacturer: WIKA Instrument Corporation Brand: WIKA Model: 9833574

The WIKA industrial pressure gauge has stainless steel wetted parts, which resist corrosion against chloride samples, and has a circular dial that is enclosed in a stainless steel case that resists corrosion. The gauge measures pressure from 15 pounds per square inch (psi) to 15,000 psi, and is accurate to a variety of percentages across the entire range of the gauge, depending on other standard features, such as dial size. Accuracy ranges are: + or - 2.5 percent of span; + or - 1 percent of span over the entire range of the gauge, or American Society for Mechanical Engineering (ASME) B40.100 Grade 1A accuracy class; or + or - 2/1/2 percent of span over the entire range of the gauge, or ASME Grade A accuracy class. The male connection is available as a lower mount, a lower back mount, or a center mount, and comes with a choice of a 1/8", 1/4", or a 1/2" National Pipe Thread (NPT) rate. This pressure gauge is suitable for use in corrosive environments.Pressure gauges are instruments used to measure the pressure of a gas or liquid inside a vessel and, often, to help ensure the optimal amount of pressure for a given application. Pressure gauges can range from everyday instruments, such as those used to measure the air pressure in a car or bicycle tire, to highly accurate gauges used in mechanical and industrial processing. Most often, pressure gauges measure pressure relative to another reference. For instance, gauge pressure measures pressure relative to ambient air. An example of a pressure gauge measuring relative to ambient air is a tire pressure gauge or a blood pressure gauge. Differential pressure is the difference in pressure between two points, such as when measuring liquid flow along various points in a pipeline. An absolute pressure gauge measures pressure relative to a perfect vacuum, such as an atmospheric or barometric pressure gauge. All types of pressure gauges include either a male or a female mount to connect to the vessel where pressure is being measured, and display results on a dial with varying...

Manufacturer: Winters Brand: Winters Model: PFQ722

The Winters PFQ series pressure gauge with brass wetted parts has a glycerin-filled circular dial enclosed in a stainless steel 304 case, and a male connection, and measures pressure with a single or dual scale with an accuracy of + or - 1.5% or 2.5%. The OT58 brass wetted parts are for measuring non-corrosive liquid and gas pressure. The stainless steel 304 case is also corrosion resistant and is Ingress Protection certified IP65 for protection against solid objects, including dust or liquids. The circular dial comes in 1.5" (40 mm), 2" (50 mm), 2.5" (63 mm), or 4" (100 mm) diameters and is filled with glycerin for protection against vibration and pulsation. The dial is white aluminum with black and red markings. It has an aluminum, anodized black, pointer and the lens is polycarbonate for high impact resistance. The gauge measures pressure with a single psi scale or a dual scale of psi/kPa, psi/bar, Hg. vacuum/kPa, or Hg. vacuum/bar. The gauge is accurate to + or - 2.5% of full scale value for the 1.5" and 2" dials and accurate to + or - 1.5% of full scale value for the 2.5" and 4" dials. The male connection comes with a 1/8", 1/4", or 1/2" NPT (National Pipe Thread) rate with a restricted orifice and is located at the bottom or center back of the gauge. The movement is OT59 brass, and the welding is silver alloy. The 6" (150 mm) socket gasket, the fill plug, and the lens ring gasket are all made of nitrile rubber for a tight seal. The over-pressure limit is 25% for pressures up to 1,400psi (9,653kPa) and 15% for pressures over 1,400psi (9,653kPa). The working pressure is a maximum of 75% of full scale value. The operating temperature is -4 to 150 degrees F (-20 to 65 degrees C). This pressure gauge is suitable for pumps, compressors, hydraulic presses, machinery, pneumatic equipment, and motors in harsh environments.Pressure gauges are instruments used to measure the pressure of a gas or liquid inside a vessel and, often, to help ensure the optimal amount of pressure for a given application. Pressure gauges ca...

Manufacturer: Dwyer Instruments Brand: Dwyer Model: 160-18

Ideal for use with our precision manometers and air velocity gauges, Dwyer® Pitot Tubes are constructed from corrosion resistant stainless steel for a lifetime of service. ASME design meets AMCA and ASHRAE specifications for maximum accuracy over a wide variety of flow conditions. No correction factors required as ASHRAE tip design yields a calibration factor of 1. ASHRAE design needs no calibration! Permanent, stamped insertion depth graduations on sides of 160 series facilitate accurate positioning. Static pressure port is parallel to sensing tube allowing quick, easy alignment of tube with air flow. Low sensitivity to misalignment gives accurate reading even when tube is misaligned up to 15 degrees. Various standard sizes are available for use in ducts as small as 4" dia. or as large as 36 ft. dia. A universal model fits user supplied 3/4" schedule 40 (standard) pipe in any length. Several convenient mounting options are available for permanent installations.

Manufacturer: WIKA Instrument Corporation Brand: WIKA Model: 9699134

The WIKA industrial pressure gauge has copper alloy wetted parts, which resist corrosion against salty liquids, and a circular dial that is enclosed in a stainless steel case that resists corrosion against most samples. The gauge measures pressure from 15 pounds per square inch (psi) to 15,000 psi. It is accurate to + or - 1 percent of span over the entire range of the gauge, or American Society for Mechanical Engineering (ASME) B40.100 Grade 1A accuracy class; or + or - 2/1/2 percent of span over the entire range of the gauge, or ASME Grade A accuracy class. The male connection is available as a lower mount, a lower back mount, or a center back mount, and comes with a choice of a 1/8", 1/4", or 1/2" National Pipe Thread (NPT) rate. This pressure gauge is suitable for gaseous or liquid samples, including those found in hydraulics and compressors in the process industry.Pressure gauges are instruments used to measure the pressure of a gas or liquid inside a vessel and, often, to help ensure the optimal amount of pressure for a given application. Pressure gauges can range from everyday instruments, such as those used to measure the air pressure in a car or bicycle tire, to highly accurate gauges used in mechanical and industrial processing. Most often, pressure gauges measure pressure relative to another reference. For instance, gauge pressure measures pressure relative to ambient air. An example of a pressure gauge measuring relative to ambient air is a tire pressure gauge or a blood pressure gauge. Differential pressure is the difference in pressure between two points, such as when measuring liquid flow along various points in a pipeline. An absolute pressure gauge measures pressure relative to a perfect vacuum, such as an atmospheric or barometric pressure gauge. All types of pressure gauges include either a male or a female mount to connect to the vessel where pressure is being measured, and display results on a dial with varying increments of measure across a given range.WIKA Instrument Corporation is a globa...

Manufacturer: Dwyer Instruments Brand: Dwyer Model: 1223-20-D

These inexpensive manometers measure positive, negative and differential pressures. Dwyer Flex-Tube U-Tube Manometers combine the inherent accuracy of the simple "U" Tube with the durability of tough, long-lasting plastic construction. Columns are of .375" O.D. flexible and shatter proof clear butyrate tubing. They are easily accessible for cleaning. Indicating tube is backed by white scale channel to provide maximum color contrast. Scales are extruded high impact polystyrene plastic, formed to hold columns in perfect alignment. Stark white scales have graduations and numbers silkscreen-printed in black for maximum legibility.

Manufacturer: Ashcroft Inc. Brand: Ashcroft Model: 251009SW02BXLLV/30#/BR

Ashcroft is pleased to reintroduce the 1009SW Duralife pressure gauge. This gauge has been upgraded with many new features outlined above while maintaining the tried and true performance and quality you have come to expect. Duralife 1009SW gauges provide significant features and benefits. New features include a ventable plug that can be sealed or vented depending on your environment and a patent pending through-dial recalibration that reduces recalibration time. The combination of features including the patented PowerFlex movement and optional PLUS! Performance dampening system in the 1009SW is the finest gauge technology for vibration, shock and pulsation applications. Available in pressure ranges from vacuum to 15,000 psi, including compound and metric ranges

Manufacturer: Dwyer Instruments Brand: Dwyer Model: DPGW-09

The Series DPGW is the only economic digital pressure gage for liquids with the ability to select engineering units on the market. With its 1% accuracy and digital push-button zero, the DPGW is the perfect choice for digitally monitoring the pressures of air and compatible liquids and gases.