Pressure Calibrators - Page 13

Manufacturer: Fluke Corporation Brand: Fluke Model: TP82

Flexible and formable 1-1/4" pin provides an easy connection past weather pack seals to connector conductors. Tested to over 60 VDC, these pins are a must-have for fuel injectors, TPS and MAP sensors, as well as for any underhood or under vehicle connector with weather pack seals. The bright yellow body stands out in an engine compartment to ensure they are not left behind. Easily connects to test leads that have removable ends. Banana jack accepts all DMM and banana jack leads.

Manufacturer: Fluke Corporation Brand: Fluke Model: TP81

Stainless steel probe pierces insulation on 14, 16 and 18 gauge wire. You control needle depth to minimize insulation damage. Essential for use under hood or under dash. Use it on fuel injectors or sensors while providing complete insulation to grounding due to design. The TP81 connects to banana jack leads. Banana jack accepts all DMM and banana jack leads. Non-rotating banana jack prevents leads from tangling, allowing you to tighten/loosen clamp while still connected to the test lead. For use with test leads with 4mm banana plugs. Tested to 60V DC.

Manufacturer: Fluke Brand: Fluke Model: FLUKE-IR3000FC

Available for sale in the United States and Canada only See, save, and share data wirelessly — saving time and increasing productivity Increase productivity by communicating wirelessly between your phone, PC, and Fluke test tools Download the Fluke Connect™ app for use with iOS (4s and later) and Android™ to connect with over twenty Fluke test tools (Download iOS app at the App Store, and the Android app from Google play) Logging function on modules allow you to isolate intermittent events or record signal fluctuations remotely Share data with associates in seconds, allowing for immediate interpretation and action Increase efficiency by simultaneously viewing multiple measurements on one screen Take measurements from safe locations reducing potential hazards

Manufacturer: Fluke Corporation Brand: Fluke Model: Fluke 323 Color: Multicolored

The Fluke true-rms clamp meter is a great clamp meter for general, grab-and-go troubleshooting needs. The Fluke 323 323-AMZN is ideally suited for current measurements up to 400 a in tight cable compartments.

Manufacturer: Fluke Corporation Brand: Fluke Model: EBC290

External battery charger for use with BP290 and BP291 LI-ion Batteries.

Manufacturer: Palmer Instruments, Inc. Brand: Palmer Model: MPTKR

The Palmer MPT Residential Kit contains one MPTA Ace Tester (featuring three ¼" NPT Ports and four internal NPT threads of 1", ¾", ½", and 3/8"). Tester is made of aircraft quality aluminum. Kit includes one 35 oz. (60 inches of water) pressure gauge, and one 34 kpa (5 PSI) pressure gauge, both with 1/4" NPT threads. Residential Kit also includes one Mini Ball Valve, one Hand Pump with Check Valve, one Schrader Valve, one 1/4" Male Quick Connect Fitting, one Hose Bib Adapter for Hydrostatic Testing, and one 1/4" x 1/8" Hose Connection. Kit comes in hard plastic case with foam lining to keep everything together and protected for easy grab and go.

Manufacturer: Fluke Corporation Brand: Fluke Model: STL120-III

Set of two (one red, one gray) double insulated silicone shielded test leads for noise free measurements. Specially designed for use with the Fluke ScopeMeter 120 series. Compatible with AC120 alligator clips and HC120 hook clips. Safety designed ground leads included. Integral strain relieve and extra hard probe tips provide extra long service life. Features safety designed shrouded plugs and notched tip to prevent probe from sliding. Bandwidth: 12,5 MHz. Maximum signal voltage: 600V rms, CAT III per IEC 61010-031:2008. Maximum voltage to ground: 600V rms, CAT III per IEC 61010-031:2008. Maximum current: 1A. 2mm Add-on test pin: 600V, CAT II per IEC 61010-031:2008. Length: 1.2m.

Manufacturer: Fluke Corporation Brand: Fluke Model: 87-RETROFIT

RETROFIT Kit for 83, 85, 87-3, 787 multi meters.

Manufacturer: Fluke Corporation Brand: Fluke Model: FLUKE-FP Color: White

The Fluke FoodPro infrared thermometer takes noncontact temperature measurement and is used to monitor the surface temperatures of food products and foodservice equipment. This thermometer measures temperature from -30 to +200 degrees C (-20 to +390 degrees F) with an accuracy of + or - 1 degree C (+ or - 2 degrees F) from 0 to 65 degrees C (32 to 150 degrees F) and + or - 1.5% of the reading above 65 degrees C (150 degrees F). It has a 2.5:1 infrared distance-to-spot ratio with LED illumination for highlighting the measurement area. Go/No-Go lights indicate when food is in an unsafe temperature range (40 to 140 degrees F) to meet Hazard Analysis of Critical Control Points (HACCP) guidelines. It is Ingress Protection certified IP54 for dust and splashing liquid and can be hand washed without submersion after use. The CE mark indicates compliance with applicable European Union (EU) directives. It comes with one AA battery and instructions. This thermometer is used by foodservice professionals to measure food product and equipment temperatures and help detect potential food safety problems.SpecificationsTemperature range-30 to +200 degrees C (-20 to +390 degrees F)Infrared sensor accuracy0 to 65 degrees C (32 to 150 degrees F): + or - 1 degree C (+ or - 2 degrees F); above 65 degrees C (150 degrees F): + or - 1.5% of the reading; below 0 degrees C (32 degrees F): + or - 1 degree C (+ or - 2 degrees F) + or - 0.1 degreeDisplay resolution0.2 degree C / 0.4 degree FDistance-to-spot ratio2.5:1Working range25 to 250mm / 1 to 10 inchesPower SupplyAA batteryWeight100gDimensions150 x 30 x50mm (H x W x D)H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.Digital infrared thermometers measure the temperature of surfaces from a distance. They may measure temperature in Celsius, Fahrenheit, or both. Infrared (IR) thermometers work by focusing the infrared radiation emitted by a surface onto a detecto...

Manufacturer: Fluke Corporation Brand: Fluke Model: T5-H5-1AC KIT/US Color: T5-H5-1AC Electrical Tester Kit

This kit is designed to help electricians and HVAC technicians solve problems quicker. Test first for overheated electrical devices using an IR thermometer; then use electrical test tools to find out more about the problem.