Gage Blocks & Accessories - Page 21

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 516-101-26

All Mitutoyo gage blocks meet or exceed all known specifications. The flatness, parallelism and surface finish necessary to achieve the required accuracies are the same as or better than government requirements. A Certificate of Inspection is furnished with all Mitutoyo gage blocks with a serial number on the case and an identification number on each block. The deviation of each block is registered. For this inspection, each gage block is measured relative to the upper level master using a gage block comparator. Grade K gage blocks are manufactured by absolute measurement using an interferometer. The gage block set and discrete gage block are supplied with a Certificate of Calibration. The Certificate of Calibration specifies the deviation from the nominal length. (Comparative measurement, however, is performed for all square gage blocks.). A Certificate of Accuracy, traceable to the NIST, is furnished with each MITUTOYO gage block set and individual block.

Manufacturer: ABS Import Tools, Inc. Brand: HHIP Model: 4101-0008

HHIP high precision steel plug gage sets with wood custom drawer system features no-go (minus) 001" set increments tool steel: 60/62 HRC 10 Micro finish or better within 0001" round Class ZZ OAL: 2". uses: checking locations, measuring hole sizes and depths, go and no-go gauging, setting micrometers, checking distances between holes.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 516-934-26

The Mitutoyo 516-934-26 gage block set includes nine ASME grade 0 steel rectangular gage blocks with nominal size engraved in inches. Blocks included in the set measure .0625", .100", .125", .200", .250", .300", .500", 1", and 2". Grade 0 gage blocks are often used for calibrating and inspecting tools, instruments, and manufacturing gages. This rectangular gage block set meets ASME B89.1.9 standards and a certificate of inspection and calibration is provided with each set. Gage blocks (also called gauge blocks, Jo blocks, Hoke blocks, and Johansson gauges) are precision ground and lapped metal or ceramic blocks, used for calibrating precision measuring equipment and as a length standard in manufacturing. Gage blocks are square or rectangular in shape, with flat and parallel measuring surfaces, and usually have an engraved unique serial number and nominal length (provided in either inches or millimeters). They often come in sets with blocks of varying lengths, so that many different standard lengths can be created by stacking and wringing them. Wringing is the process of sliding blocks together with a small amount of pressure, in order to create a longer gage block stack. Gage blocks are kept within a protective case, are cleaned thoroughly before wringing and after each use to prevent corrosion, and are kept free of burrs and other damage that would decrease their accuracy. Temperature is another important consideration. Blocks are susceptible to thermal expansion and must be used at 68 degrees F to ensure their accuracy. Gage blocks are available in different grades, which refer to their tolerance or allowable deviation from their nominal dimension. Grades are defined by the American Society of Mechanical Engineers (ASME) B89.1.9M for both length and flatness. ASME B89.1.9M also defines standards for parallelism and surface finish. Different grades are available depending on the application and the required level of accuracy. Grade 00 blocks are generally used to calibrate and check the accuracy of instrum...

Manufacturer: RPM Brand: RPM Model: RPMC8130

OverviewRPM designers went all out to create the most innovative and useful tool to check your vehicle’s ride height! (A vehicle’s ride height is the static height of the vehicle as it rests on its suspension. It varies from front to rear and from one side to the other depending upon weight and spring tension.) The gauge has a graduated scale along the upper edge of the base with easy to read lines and numbers. Each graduation on the inch scale (81300) represents 0.025" and on the metric scale (81150), 0.5mm. (for extreme accuracy, the graduations are far enough apart that they may be split to read as little as 0.012" [81300] or 0.25mm. [81150])! Included with the gauge is a spring-loaded tensioning knob to keep the gauge positioned while checking & setting positions on the gauge. The RPM 81300 Ride Height Gauge (inch scale) has a range from 0.150" to 1.150" (5/32" to 1-5/32") and the 81150 Ride Height Gauge (metric scale) has a range from 4mm. to 29.5mm.! RPM’s ingenious design uses a base and a slide that travels along a twenty degree angle. By using such a slight angle, the accuracy of the gauge increases dramatically while still allowing a broad height range. Either gauge may be used to check most on-road or off-road vehicle’s ride height, including pan cars & sedans! It’s extremely easy to use and is the most accurate tool available on the R/C market!

Manufacturer: ABS Import Tools, Inc. Brand: HHIP Model: 4101-0710

HHIP individual rectangular gage block is supplied with a Manufacturer's certificate. Grade as-0 (2). offering n.I.S.T. Traceable calibration conforms to mil Std 45662a, ggg G 15C, ISO/IEC 17025 accredited, ISO 9000, 10012 1, ANSI ncsl Z540 1 and ISO guide 25 certified. Tolerance is +0.000004/-0.0000002". size is 0.1008".

Manufacturer: ABS Import Tools, Inc. Brand: HHIP Model: 4101-0718

HHIP individual rectangular gage block is supplied with a Manufacturer's certificate. Grade as-0 (2). offering n.I.S.T. Traceable calibration conforms to mil Std 45662a, ggg G 15C, ISO/IEC 17025 accredited, ISO 9000, 10012 1, ANSI ncsl Z540 1 and ISO guide 25 certified. Tolerance is +0.000004/-0.0000002". size is 0.107".

Manufacturer: ABS Import Tools, Inc. Brand: HHIP Model: 4101-0745

HHIP individual rectangular gage block is supplied with a Manufacturer's certificate. Grade as-0 (2). offering n.I.S.T. Traceable calibration conforms to mil Std 45662a, ggg G 15C, ISO/IEC 17025 accredited, ISO 9000, 10012 1, ANSI ncsl Z540 1 and ISO guide 25 certified. Tolerance is +0.000004/-0.0000002". size is 0.134".

Manufacturer: TTC Brand: TTC

Use for set-up and layout on drill presses and milling machines.

Manufacturer: LittleMachineShop.com Brand: LittleMachineShop.com Model: LMS2881

These ultra precision 1-2-3 blocks are ground and case hardened on all sides to 55-60 Rc. They are parallel within 0.0001", flat within 0.0001" and square within 0.0001". They are up to 0.0003" oversize for lapping. Each set includes two matched blocks. T

Manufacturer: LittleMachineShop.com Brand: LittleMachineShop.com Model: LMS2881

These ultra precision 1-2-3 blocks are ground and case hardened on all sides to 55-60 Rc. They are parallel within 0.0001", flat within 0.0001" and square within 0.0001". They are up to 0.0003" oversize for lapping. Each set includes two matched blocks. T