Dimensional Calibration - Page 116

Manufacturer: Accusize Co. Ltd. Brand: Accusize Industrial Tools Model: 0005-2411

100 Concentration 150 Grit

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611875-541

The Mitutoyo grade AS-1 rectangular gage block is made of steel, has its nominal length engraved in metric [millimeter (mm)], and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade AS-1 gage block is commonly used for workshop and inspection applications to calibrate fixtures and precision instruments, to inspect a variety of tools such as mounting tools, cutters, fixtures, and mechanical parts, and for manufacturing gage applications. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear-resistance. This gage block has a rectangular base for accurate wringing. Nominal length is measured in metric [millimeter (mm)], and indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 9 millimeters. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment and to standa...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611875-541

The Mitutoyo grade AS-1 rectangular gage block is made of steel, has its nominal length engraved in metric [millimeter (mm)], and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade AS-1 gage block is commonly used for workshop and inspection applications to calibrate fixtures and precision instruments, to inspect a variety of tools such as mounting tools, cutters, fixtures, and mechanical parts, and for manufacturing gage applications. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear-resistance. This gage block has a rectangular base for accurate wringing. Nominal length is measured in metric [millimeter (mm)], and indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 9 millimeters. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment and to standa...

Manufacturer: Accusize Co. Ltd. Brand: Accusize Industrial Tools Model: EG02-0224

Vee Block dimensions: 3'' long, 1-3/16'' wide, 1-3 x 16'' high Angle plate dimensions: 2-3/4'' long, 1-3/16'' wide 5/64'' high at narrow end Set Includes: V-Block 10°, 15°, 30° Angle Plate 1°, 2°, 3°, 4°, 5°

Manufacturer: HHIP Brand: HHIP Model: 3402-0209

Convenient clamping slots for mounting and are widely used for machining, layout and inspection. Made of high tensile cast iron properly seasoned against distortion. Open-End style, accurately machined square and parallel on all faces. Slot A is 90 degrees to slot C.

Manufacturer: ABS Import Tools Inc. Brand: HHIP Model: 3402-0018

HRC 45 to 50 heat treatment. Angle Accuracy: ±5' Combination V-block and angle plate for rapid, easy setting. No sine vise, sine plate, angle vise, chart or gage block needed. Set Includes: V-Blocks: 10, 15, 30 degrees, Angle plates: 0.5, 1, 2, 3, 4, 5 degrees.

Manufacturer: Tuthill Brand: Fill-Rite Model: KIT900GR

Built into every fuel transfer pump, chemical transfer pump and meter is over 50 years of experience—and the pride and workmanship associated with the moniker “Made in USA”. We use only the most durable materials to insure long life and dependability. Fill-Rite and Sotera branded products deliver superior performance time and time again, regardless of the application or installation.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 613193-531

The Mitutoyo grade 0 rectangular gage block is made of ceramic, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 0 gage block is commonly used in workshop and inspection applications to calibrate and inspect mechanical parts and tools, to verify the accuracy of plug and snap gages, and to set electronic measuring devices. It is made of ceramic which resists corrosion, abrasion, and burrs, withstands high temperatures without melting (high thermal expansion resistance), and provides dimensional stability. This gage block has a rectangular base for accurate wringing. Nominal length is measured in inches, and is indicated on the block with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.355 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment and to standardize the measurement o...

Manufacturer: ABS Import Tools Inc. Brand: HHIP Model: 3402-0019

Get quick setups for fringing various angles from 1/4 to 45 degrees Hardened steel With fitted case INCLUDES: 1/4, 1/2, 1, 2, 3, 4, 5, 10, 15, 20, 25, 30, 35, 40, & 45 degrees and 2 riser blocks.

Manufacturer: HHIP Brand: HHIP

Toomaker's V-Block with Clamp ~ Block is hardened and precision ground. ~ This block is a versatile tool for grinding, milling or drilling. ~ Side screw supports the block and prevents tilting. ~ Blocks have four 3/8"-26 tapped holes, two in the base and one on each side to attach to an angle iron. ~ The angle iron holding the block can then be attached to a lathe face plate or held by a magnetic chuck. ~ A clearance hole for drilling or removing dowel pins is provided in the block.