|
|
-
3.7 of 5.0 with 15 Reviews
SALE PRICE: $134.00
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 611170-516
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 611170-516
|
All Mitutoyo gage blocks meet or exceed all known specifications. The flatness and parallelism surface finish necessary to achieve the required accuracies are the same as or better than government requirements. A certificate of inspection is furnished with all Mitutoyo gage blocks with a serial number on the case and an identification number on each block. The deviation of each block is registered. For this inspection, each gage block is measured relative to the upper level master using a gage block comparator. Grade K gage blocks are manufactured by absolute measurement using an interferometer. The gage block set and discrete gage block are supplied with a certificate of calibration. The certificate of calibration specifies the deviation from the nominal length. (Comparative measurement, however, is performed for all square gage blocks.). A certificate of accuracy, traceable to the NIST, is furnished with each Mitutoyo gage block set and individual block.
-
3.7 of 5.0 with 40 Reviews
SALE PRICE: $135.00
Manufacturer: Flexbar
Brand: Flexbar
Manufacturer: Flexbar
Brand: Flexbar
Flexbar Precision V-Blocks and Clamps. Made in U.S.A. Dimensions 1 1/4" x 1 1/4" x 1 5/8" Long. Capacity: Large Vee - 1 inch Diameter. Small Vee - 1/2 inch Diameter. Hardened and Ground Steel. Accuracy: Square Within .0002" per inch. Parallel Within .0002 inch. Serial Numbered in Matched pairs. Two Vee Blocks and Two Clamps.
-
3.7 of 5.0 with 36 Reviews
SALE PRICE: $139.00 1% OFF
Manufacturer: GASCO
Brand: Gasco
Manufacturer: GASCO
Brand: Gasco
70 Series Calibration Gas Regulator for NON-reactive Calibration Gas Mixtures, Cylinders: 34LA Aluminum, 58L, 74L, 116L and 103 Steel Cylinders, ecosmart cylinders: 44es,58es,66es, and 116es
-
3.7 of 5.0 with 48 Reviews
SALE PRICE: $139.58 19% OFF
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 611645-516
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 611645-516
|
All Mitutoyo gage blocks meet or exceed all known specifications. The flatness and parallelism surface finish necessary to achieve the required accuracies are the same as or better than government requirements. A certificate of inspection is furnished with all Mitutoyo gage blocks with a serial number on the case and an identification number on each block. The deviation of each block is registered. For this inspection, each gage block is measured relative to the upper level master using a gage block comparator. Grade K gage blocks are manufactured by absolute measurement using an interferometer. The gage block set and discrete gage block are supplied with a certificate of calibration. The certificate of calibration specifies the deviation from the nominal length. (Comparative measurement, however, is performed for all square gage blocks.). A certificate of accuracy, traceable to the NIST, is furnished with each Mitutoyo gage block set and individual block.
-
3.7 of 5.0 with 3 Reviews
SALE PRICE: $142.49
Manufacturer: FISHER
Brand: Fisher
Manufacturer: FISHER
Brand: Fisher
Includes: Two 1-7/8" x 2-3/8" x 2" magnetic v-blocks (1/2" and 2" round capacity). Cast integrally with aluminum to insure the blocks will never crack or become loosened even when accidentally dropped. Steel used is selected for the highest magnetic transfer and low retention of magnetic flux.
-
3.7 of 5.0 with 29 Reviews
SALE PRICE: $143.73 40% OFF
Manufacturer: L.S. Starrett
Brand: Starrett
Manufacturer: L.S. Starrett
Brand: Starrett
End Measuring Rod is used for checking and setting micrometers of 2 capacity and larger. Also use on machine tools for comparing gages, checking precision measuring tools, and measuring parallel surfaces. Insulated handles minimize expansion by heat when held in the hand. This listing is for each. Technical Specification Item End Measuring Rod w/Grip Dia. 11mm Range 450mm For Use With 475mm Micrometers, Includes Insulating Rubber Handle
-
3.7 of 5.0 with 38 Reviews
SALE PRICE: $143.73 11% OFF
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 516-809-26
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 516-809-26
|
The Mitutoyo 516-series Grade 0 Carbide Rectangular Inch Wear Gage Block Set includes a set of rectangular-shaped, tungsten carbide wear gage blocks with nominal length engraved in inches on each, and is supplied with a Mitutoyo inspection certificate that states that the blocks meet American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade 0 standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of each individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself.Wear gage blocks are wrung with frequently used gage blocks to prevent wear. Grade 0 gage blocks are commonly used in workshop and inspection applications to calibrate and inspect mechanical parts and tools, to verify the accuracy of plug and snap gages, and to set electronic measuring devices. Tungsten carbide is harder than steel and ceramic for greater resistance to wear, and more resistant to thermal expansion for accuracy. Rectangular-shaped blocks provide accurate wringing. The nominal length of each block is measured in inches, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on each block for traceability. The set comes with a fitted wooden case for storage.The set includes a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the blocks meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish.Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measur...
-
3.7 of 5.0 with 38 Reviews
SALE PRICE: $143.73 11% OFF
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 516-809-26
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 516-809-26
|
The Mitutoyo 516-series Grade 0 Carbide Rectangular Inch Wear Gage Block Set includes a set of rectangular-shaped, tungsten carbide wear gage blocks with nominal length engraved in inches on each, and is supplied with a Mitutoyo inspection certificate that states that the blocks meet American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade 0 standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of each individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself.Wear gage blocks are wrung with frequently used gage blocks to prevent wear. Grade 0 gage blocks are commonly used in workshop and inspection applications to calibrate and inspect mechanical parts and tools, to verify the accuracy of plug and snap gages, and to set electronic measuring devices. Tungsten carbide is harder than steel and ceramic for greater resistance to wear, and more resistant to thermal expansion for accuracy. Rectangular-shaped blocks provide accurate wringing. The nominal length of each block is measured in inches, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on each block for traceability. The set comes with a fitted wooden case for storage.The set includes a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the blocks meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish.Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measur...
-
3.7 of 5.0 with 29 Reviews
SALE PRICE: $143.73 40% OFF
Manufacturer: L.S. Starrett
Brand: Starrett
Manufacturer: L.S. Starrett
Brand: Starrett
End Measuring Rod is used for checking and setting micrometers of 2 capacity and larger. Also use on machine tools for comparing gages, checking precision measuring tools, and measuring parallel surfaces. Insulated handles minimize expansion by heat when held in the hand. This listing is for each. Technical Specification Item End Measuring Rod w/Grip Dia. 11mm Range 450mm For Use With 475mm Micrometers, Includes Insulating Rubber Handle
-
3.7 of 5.0 with 28 Reviews
SALE PRICE: $144.77 1% OFF
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 614224-531
Manufacturer: Mitutoyo
Brand: Mitutoyo
Model: 614224-531
|
This Mitutoyo grade 0 square gage block is made of steel, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 0 gage block is commonly used in workshop and inspection applications to calibrate and inspect mechanical parts and tools, to verify the accuracy of plug and snap gages, and to set electronic measuring devices. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear resistance. This gage block has a square base for accurate wringing, to attain a height reference standard, and for the ability to make a dedicated inspection jig. Nominal length is measured in inches, and indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.95 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment and to standardi...
|
|