Dimensional Calibration - Page 29

Manufacturer: Flexbar Brand: Flexbar

Precision V-Blocks and Clamps. All sides are ground Square and Parallel to each other. Matched Accuracy .0002" and numbered in pairs. Sturdy enough to be used in matching operation. Supplied With two Clamps.

Manufacturer: TTC Brand: TTC

"V" block has (4) 3/8"-16 tapped holes, (2) in the base and (1) on each side for angle iron clamping. Parallelism tolerance of Vee axis to base: within .0003"/8 microns Dimensions: 3-5/8"L x 1-7/8"W x 1-7/8"H Holding capacity: 1-5/16"

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611587-521

The Mitutoyo grade 00 rectangular gage block is made of steel, has its nominal length engraved in metric [millimeter (mm)], and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade 00 gage block is commonly used within a controlled environment as a reference standard for setting high-precision measuring equipment, to calibrate low-grade gage blocks, and to inspect the accuracy of gages, mechanical parts, and tools. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear-resistance. This gage block has a rectangular base for accurate wringing. Nominal length is measured in metric [millimeter (mm)], and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 9 millimeters. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment and to standardize the measuremen...

Manufacturer: ABS Import Tools, Inc. Brand: HHIP Model: 4401-0012

HHIP 12 inch digital protractor features surface plates are checked by auto-collimator for overall accuracy assurance. Granite surface plates meet or exceed Federal specifications ggg-p-463c. Product specifications: size: 18 x 12 x 3"; accuracy: +/-0001"; W.T. (Lbs.): 80.

Manufacturer: Hexagon Metrology Brand: Brown & Sharpe

Designed for calibrating micrometers and zeroing vernier, dial, and digital calipers. 3/8" tubular with 1/4" diameter flat ends. Standard have two insulating grips to protect rods from heat of hands. Meets federal specifications.

Manufacturer: Generic

9 Blocks -- .1001" thru .1009" step of .0001" 9 Blocks -- .101" thru .109" step of .001" 9 Blocks -- .110" thru .190" step of .010" 4 Blocks -- .200, .300, .400, .500" 3 Blocks -- 1.000, 2.000, 4.000" 2 Blocks -- .050, .100"

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611821-551

The Mitutoyo grade AS-2 rectangular gage block is made of steel, has a nominal length engraved in metric [millimeter (mm)], and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade AS-2 gage block is commonly used in workshops for calibrating and inspecting mounting tools and cutters. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear resistance. This gage block has a rectangular base for accurate wringing. Nominal length is measured in metric [millimeter (mm)] units, and is indicated on the block with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 9 millimeters. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment and to standardize the measurement of length in manufacturing industries. They are commonly made of precision-ground steel, ceramic, or carbide mat...

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 612105-541

The Mitutoyo grade AS-1 rectangular wear gage block is made of tungsten carbide, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself.Wear gage blocks are wrung with frequently used gage blocks to prevent wear. This grade AS-1 gage block is commonly used for workshop and inspection applications to calibrate fixtures and precision instruments, to inspect a variety of tools such as mounting tools, cutters, fixtures, and mechanical parts, and for gage manufacturing applications. It is made of tungsten carbide, which is harder than steel and ceramic for greater resistance to wear, and is more resistant to thermal expansion for accuracy. This gage block has a rectangular base for accurate wringing. Nominal length is measured in inches, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.355 inches. It comes in a carrying case with a padded, formed interior.This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish.Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Jo...

Manufacturer: TTC Brand: TTC

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 616195-541

The Mitutoyo grade AS-1 square gage block is made of ceramic, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade AS-1 gage block is commonly used for workshop and inspection applications to calibrate fixtures and precision instruments, to inspect a variety of tools such as mounting tools, cutters, fixtures, and mechanical parts, and for gage manufacturing applications. It is made of ceramic, which resists corrosion, abrasion, and burrs, can withstand high temperatures without melting (high thermal expansion resistance), and provides dimensional stability. This gage block has a square base for accurate wringing, to attain a height reference standard, and for the ability to make a dedicated inspection jig. Nominal length is measured in inches, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.95 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo...