Layout Tools - Page 26

Manufacturer: QLT by Marshalltown Brand: Qlt By Marshalltown Model: TS917

Marshalltown TS917 QLT Drywall T-square Marshalltown TS917 QLT Drywall T-square Features: Silver anodized finish with black epoxy paint numerals for long wear and legibility Reverse ruled to read from either edge Head is notched to permit full length cut Stud location marks aid in nailing Made in USA Marshalltown TS917 QLT Drywall T-square Specifications: Silver anodized finish with black epoxy paint numerals for long wear and legibility Reverse ruled to read from either edge Head is notched to permit full length cut Stud location marks aid in nailing 47 7/8-Inch long.

Manufacturer: Shinwa Japanese Measuring Tools

This precision 600 mm metric rigid ruler is made by Shinwa Measuring Corporation, a premier tool manufacturer. Rule is made from spring tempered and hardened stainless steel and is 1.180" wide by .052" thick. It has a "zero-glare" satin chrome finish on the face that can be easily read in both low and bright light conditions. One face has metric graduations in both .5mm and mm and the reverse side has metric conversion tables and tap drill sizes. Graduations are precision photo etched and then black filled for easy readability. 100 mm divisions are marked in red. The sides of each rule are precision ground parallel to each other. One end is accurately ground square to allow accurate reading, while the other end is rounded with a hole for hanging.

Manufacturer: Grizzly Brand: Grizzly Model: T10263

This Ebony Sliding Bevel is the ideal tool for measuring and transferring angles. Beautiful ebony and brass construction. Features a 9" blade for setting acute, obtuse and supplementary angles. Thick, inlaid brass adds protection. Large knurled knob makes angle setting quick and easy.

Manufacturer: Johnson Level & Tool Brand: Johnson Level & Tool Model: 3848 Color: Black

48" contractor magnetic machined top reading aluminum level, 3 vial, extruded aluminum I-Beam with BLACK anodized finish, precision machined leveling edges & strong, full length magnetic strip, large, magnified top read window, 360 degree acrylic yellow barrel vials, screw on, high impact resistant plastic covers with protective lenses, shock protecting end caps, frame dimensions: 1" x 2-1/4".

Manufacturer: STARRETT Brand: Starrett

Picture may represent similar item C604R-6 6" QR RULE 52678

Manufacturer: PEC Tools Products Engineering Company

This precision 6" 16R rigid hook rule is made in the USA by Products Engineering Company (PEC Tools), a premier tool manufacturer. Rule is made from spring tempered and hardened steel and is .750" wide by .042" thick. It has a "zero-glare" satin chrome finish that provides better rust resistance than polished steel and can be easily read in both low and bright light conditions. The sides of each rule are ground parallel and each end is accurately ground square to allow reading from either end. 16R graduations have 1/50" and 1/100" on one side and quick-reading 1/32" and 1/64" on the other. Graduations are precision photo etched and then black filled for easy readability.

Manufacturer: No-Dog Tools, Inc. Brand: No-Dog Model: NODOG-Orange

The No-Dog is a handy tool for electricians that eliminates "dog-legs" in offsets and saddles. It is precision tooled from lightweight, durable aluminum. Measuring 1/2" by 1" by 2", it is useful as a spacer with multiple runs of conduit. This size also makes it convenient to carry. The "No-Dog" can fit easily in a pocket or tool box, or can be clipped to a hardhat or tool pouch. The No-Dog offset level is proudly made in the USA How to use your No-Dog offset level 1. Position conduit in bender. 2. Attach "No-Dog" to conduit at either end as shown below. Do not move "No-Dog" until all the bends are finished to insure that all bends will be on the same plane. 3. Adjust bender pressure on conduit so conduit is snug yet loose enough to be turned with a pair of channelloks, pipe wrench or chain wrench. 4. Turn conduit until "No-Dog" shows level. 5. Bend conduit to desired angle. 6. Release bender pressure. 7. Turn conduit 180 degrees and position at next bend mark. 8. Repeat steps 3 and 4. 9. Make next bend. 10. For additional bends on same plane, repeat steps 6, 7, 8, and 9. What's included? 1 - No-Dog offset level 1 - No-Dog hard hat sticker 1 - Offset formula and fraction to decimal conversion chart

Manufacturer: Cooper Hand Tools Brand: Apex Tool Group Model: HYT100

"COOPER TOOLS" LUFKIN SPEEDWINDER TAPE RULE 3/8"x100 Easy to read blade Rapid rewind High impact, high visibility, self standing blaze orange case Carded

Manufacturer: Stanley Brand: Stanley

3 pack contains 25', 16', and 12' tapes. High visibility fluorescent yellow color and ergonomic design. Compact size, 15% smaller than the PowerLock rule, with nonslip rubber grip. Dual operating lever design, depress to open and release to automatically lock or unlock button to provide free tape travel. Durable, high impact ABS case, 3 rivet hook, and polymer coated blade for long life. Integrated belt clip.

Manufacturer: No-Dog Tools, Inc. Brand: No-Dog Model: NODOG-Orange

The No-Dog is a handy tool for electricians that eliminates "dog-legs" in offsets and saddles. It is precision tooled from lightweight, durable aluminum. Measuring 1/2" by 1" by 2", it is useful as a spacer with multiple runs of conduit. This size also makes it convenient to carry. The "No-Dog" can fit easily in a pocket or tool box, or can be clipped to a hardhat or tool pouch. The No-Dog offset level is proudly made in the USA How to use your No-Dog offset level 1. Position conduit in bender. 2. Attach "No-Dog" to conduit at either end as shown below. Do not move "No-Dog" until all the bends are finished to insure that all bends will be on the same plane. 3. Adjust bender pressure on conduit so conduit is snug yet loose enough to be turned with a pair of channelloks, pipe wrench or chain wrench. 4. Turn conduit until "No-Dog" shows level. 5. Bend conduit to desired angle. 6. Release bender pressure. 7. Turn conduit 180 degrees and position at next bend mark. 8. Repeat steps 3 and 4. 9. Make next bend. 10. For additional bends on same plane, repeat steps 6, 7, 8, and 9. What's included? 1 - No-Dog offset level 1 - No-Dog hard hat sticker 1 - Offset formula and fraction to decimal conversion chart