Test Indicators - Page 40

Manufacturer: Hexagon Metrology Brand: Brown & Sharpe Model: 312B-1V Color: White

The Brown & Sharpe TESA Interapid 312 series dial test indicator has a white face, a 0.157" stem diameter, and inch measurements. The white dial and contrasting black hand help make measurements easy to read, and the dial face rotates to allow horizontal and vertical measurements. The carbide, ball-contact tip reaches into the workpiece for accurate measurements of turned, milled, and ground parts, and for tool setting gauges, fixtures, and inspections. The continuous clockwise pointer rotation and a revolution counter prevent plus or minus confusion. The ball-bearing lever system swivels through to 210 degrees. The dial face is mounted at a right angle to the insert's axis for mounting horizontally or vertically from the front or back of the indicator. A dovetail mount on the back of the indicator provides a rigid setup, and a 4mm swiveling shank on the front of the indicator can be mounted at a range of angles. This indicator has a Monoblock body design with pinions mounted in jeweled bearings in an isolated assembly separate from the outer body, for high accuracy. It has full-metal construction for durability and corrosion resistance. This dial test indicator meets Deutsches Institut fur Normung (DIN) 2270, and Norme Francaise (French Institute for Standardization) NF E 11-053 standards, and includes a declaration of conformity. The set includes an Interapid 312 dial test indicator, a 0.080" (2mm) ball-end carbide contact point, a point key, a Certificate of Accuracy and Traceability, and a storage box. Dial readings with three digits, such as 0-10-0, signify that the indicator has a balanced dial. Dial readings with two digits, such as 0-100, indicate that the dial has a continuous dial. Balanced dials are used to read the difference from a specific surface reference point. Continuous dials are used for direct readings and usually have a larger measurement range than balanced dials.Dial indicators are also called dial gauges, dial calipers, and probe indicators. These precision measuring tools are used to acc...

Manufacturer: Hexagon Metrology Brand: Brown & Sharpe Color: White

The Brown & Sharpe TESA Compac series lever dial test indicator has a white face, a 0.315" stem diameter, and inch measurements. The indicator can make either horizontal or vertical measurements, and the white dial and contrasting black hand help make measurements easy to read. The compact, carbide, ball-contact tip reaches into the workpiece for accurate measurements of turned, milled, and ground parts, and for tool setting gauges, fixtures, and inspections. The continuous clockwise pointer rotation helps prevent plus or minus confusion. The ball-bearing lever system swivels through to 210 degrees. The dial face mounted at the top of the indicator parallel to the axis, and two universal dovetail mounts can be used for mounting from the top or back. Dovetail mounts provide a rigid setup. This indicator is anti-magnetic for safety when used around magnetic workpieces and debris, and has full-metal construction for durability and corrosion resistance. This dial test indicator meets Deutsches Institut fur Normung (DIN) 2270, includes a serial number, and an inspection report with a declaration of conformity. The set includes a dial test indicator, a 0.080" (2mm) ball-end carbide contact point, two 15mm long rigid stems (4mm and 8mm diameter), and inspection report with a declaration of conformity, and a storage box.Dial readings with three digits, such as 0-10-0, signify that the indicator has a balanced dial. Dial readings with two digits, such as 0-100, indicate that the dial has a continuous dial. Balanced dials are used to read the difference from a specific surface reference point. Continuous dials are used for direct readings and usually have a larger measurement range than balanced dials.Dial indicators are also called dial gauges, dial calipers, and probe indicators. These precision measuring tools are used to accurately measure small linear distances and object sizes. The dial magnifies the measurement so that it can more easily be read by the human eye. Frequently used in manufacturing, laboratories, and o...

Manufacturer: Hexagon Metrology Brand: Brown & Sharpe Color: White

The set includes one each regular dial test indicator (0.060" measuring range, 0.0005" resolution, 1.5" dial diameter, 0-15-0 dial reading), rectangular attachment, reducing sleeve (inch), swivel holder (inch), storage case for measuring inserts, wrench for measuring inserts.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 543-558A

Mitutoyo 543-558A IDF Digimatic Indicator with six user-selectable resolutions of 0.00005, 0.0001, 0.0005, or 0.001”, and 0.001 or 0.01 mm, an accuracy of + or - 0.00012” (0.003 mm), a total measurement range of 0-2” (0-50.8 mm), and can be set to zero at any spindle position for measuring in either or both directions (plus or minus). The LCD display has a sealed housing that meets Ingress Protection Rating 30 (IP30) standards for dust and water protection, a 3/8” diameter stem, a steel ball contact point, and a flat back. The indicator displays maximum and minimum read hold, changes color from green to red when user-defined tolerances are exceeded, and has total indicator reading (TIR) capability that displays the absolute difference between the highest and lowest readings. A backup memory function retains user-defined setup conditions when power is interrupted, and an alarm indicates overflow errors, tolerance limit setting errors, and scale contamination. The indicator has SPC data output features that allow for data analysis, and choice of two power sources (AC or 9V battery). Dial indicators may also be called dial gauges, dial calipers, and probe indicators. These precision measuring tools are used to accurately measure small linear distances and object sizes. The dial magnifies the measurement so that it can more easily be read by the human eye. Frequently used in manufacturing, laboratories, and other industrial or mechanical fields, dial indicators are used anywhere a small measurement must be found and recorded or transferred, such as checking the variation in tolerance of a workpiece. Dial test indicators are very similar to dial indicators, except that the axis of measurement is perpendicular to the axis of the indicator. Standard dial indicators measure the displacement along the axis of the indicator. Dial indicators can be analog, with a mechanical dial, or electronic, with a digital display. Some electronic models transfer the data electronically to a computer for recordin...

Manufacturer: 3M Brand: 3M

UOM: Each Weight: .2 lbs. Used to test the sensitivity of the respirator wearer to a bitter solution. It is used with the 3Mâ"¢ Qualitative Fit Test Apparatus FT-30. 55 mL bottle.

Manufacturer: INTERAPID Brand: Brown & Sharpe

One piece, solid case. Very high sensitivity, very light measuring pressure. Jeweled mechanism fitted with ball bearings. Variety of mounting positions.

Manufacturer: Accusize Co. Ltd. Brand: Accusize Industrial Tools Model: P900-S108

Manufacturer: INSIZE Brand: INSIZE Model: 2307-2

Dial indicator, 2", graduation 001".

Manufacturer: T&O Brand: Toto

Range .008"Accuracy_Inch 0.00015"

Manufacturer: AnytimeTools Brand: Anytime Tools

Quality Professional Precision Tool Use this indicator to quickly center work pieces or fixtures on your mill. The measuring range is 0.25". The shank is 0.375" diameter and 0.75" long. The indicator is 5.5" long. Can measure internal diameters from 0.12" to 4.25" and external diameters from zero to 4.25". This set includes: Indicator body, restraining rod (prevents rotation), spring-loaded center point feeler, three straight feelers (for IDs), three curved feelers (for ODs). Features: For quick centering on milling and boring set-ups Includes 6 Feelers: 4", 8", 12" Straight 4", 8", 12" Curved 1/8" Feeler Ball Measuring Range: Internal: 5/32" - 4-1/4" External: 0 - 4-1/4" Locating Accuracy is 0.0005" of center Furnished in a fitted wood case Operates at any angle from horizontal to vertical without any change, and from internal to external by simply changing the feeler