Clamp Meters - Page 12

Manufacturer: Tekpower Brand: Tekpower Model: DT6930 Color: Tekpower TP6930

The Tekpower DT6930 is a professional true RMS digital AC/DC Clamp meter, it can measure AC/DC voltage, AC/DC current up to 1000A, resistance, frequency, capacitance, temperature as well as diode check and continuity test. It has many nice features as listed below. 　 Specifications: Display: 4,000 counts Auto/Manual Range AC True RMS AC Voltage: 40V/400V ± 1.0 % 40mV/400 mV/4V/600V ± 1.5% DC Voltage: 400mV/4V/40/400V ± 0.5 % 40mV/600V ± 0.8% AC Current: 400A ± 2.0 % 1000A ± 2.5% DC Current: 400A± 2.0 % 1000A ± 2.5% Resistance: 400Ω/4KΩ/40KΩ/400KΩ/4MΩ ± 1.0% 40MΩ ± 2.0% Capacitance: 40nF ± 3.0 % 400nF/4μF/40μF ± 2.5% 400μF ± 5.0%, 4mF ± 20.0% Frequency: 10Hz-10MHz ± 1.0 % Temperature (C/F): -50℃/-58℉---150℃/302℉ ± 3℃+1℃/5℉+2 150℃/302℉---700℃/1292℉ ± 3℃+1℃/5℉+2℉ Diodes Test Continuity buzzer Duty Cycle: 0.1% -99.9% Features: Auto/Manual Range AC True RMS Flexible Auto Power Off MAX/MIN Data Hold Back light Accessories: Carrying pouch K-type Thermo probe Test leads User Manual

Manufacturer: Amprobe Brand: Amprobe Model: 4560537

AMP-210 600A AC True-RMS Professional Electrical Clamp Meter with low pass filter, Amp-Tip, NVC, Audible continuity and diode test, large LCD Backlit display, CAT III 600 V.

Manufacturer: Extech Instruments Brand: Extech Model: ETK35

This special value Electrical Test Kit is assembled with True RMS Meters to provide all the electrical testing needs for installation and repair of electrical systems, HVAC equipment and large appliances, plus AC/DC Clamp Meter for automotive and motor applications.

Manufacturer: Fluke Corporation Brand: Fluke Model: TLK281

Kit includes (1) Insulation piercing clip set, (1) SureGrip silicone test lead set, (1) SureGrip test probe set, (1) SureGrip alligator clip set, (1) SureGrip large jaw alligator clip set, (1) Soft case. Complete set of test and measurement accessories designed especially for automotive specialists. Use the sharp stainless steel probes to contact the wire conductor or pinpoint tests on a circuit or relay, and the large jaw alligator clips to get a good ground on the engine or to connect to the battery terminals. An extra long set of alligator clips easily grip to the alternator BAT terminal or the S terminals. The set comes with silicone test leads and a case to keep it organized. Tested to 60V DC.

Manufacturer: Fluke Corporation Brand: Fluke Model: FVF-BASIC

FlukeView Forms Basic can be used alone to download measurement data and create reports that can be saved and printed. FlukeView Forms comes with an array of standard analysis and reporting forms that get you started on displaying your data in tables, graphs or helpful diagrams. You can leave notes on the forms to draw attention to a particular event. Share or store your data with co-workers or clients - print forms, export to other software programs, or have co-workers and clients down load the free FlukeView Demo/Reader to view and interact with your captured data. To address the increasing demands for reporting and documentation. It increases the power of your Fluke tool by enabling you to document, store and analyze individual readings or series of measurements, then convert them into professional-looking documents. The ability of FlukeView Forms to support multiple instruments enables the user to install and learn only one software application in order to use these multiple tools fully. Owners of Fluke 280 series, 180 series, 789 and 1550B, who do not need the full power of FlukeView forms, can use FlukeView Basic version. Transfer data points from your meter to your PC and use the two standard, non-customizable forms to display your readings in table or graphical form. For a larger array of forms or to use FlukeView Forms Designer to customize your forms, upgrade to FlukeView Forms version 3.3 with FVF-UG (sold separately). Comes with USB/IR cable. Number of standard forms: 2. Number of multiple meters whose data can be viewed simultaneously: 1. Number of concurrently running instances of FlukeView Forms allowed: 1. Requirements: Operating system: Windows 2000, Windows XP, Windows Vista or Windows 7. Minimum PC Hardware: Pentium class or better microprocessor, 32 MB RAM, 70 MB hard disk space (100 MB to install), USB port. FlukeView Forms supports the following test tools: 280 Series, 789, 1550B, 1653, 180 Series. Size: 203 x 100 x 50mm.

Manufacturer: FLIR Systems, Inc. Brand: FLIR Model: TA72

The FLIR Universal Flex Current Probe Accessory is designed to add capabilities, simplify challenges and get the best readings with your existing meter. Made with a narrow, 25 cm (10") flexible coil clamp, you can easily take measurements in tight or awkward spots. Coupled with a standard output, it's compatible for use with most digital multimeters and clamp meters, regardless of brand. Comes with probe, batteries and manual.

Manufacturer: Fluke Corporation Brand: Fluke Model: TLK282

Kit includes insulation piercing clip set, automotive back probe pins (five), SureGrip silicone test lead set, SureGrip test probe set. Also includes SureGrip alligator clip set, SureGrip large jaw alligator clip set, SureGrip hook clip set, Soft case. Use the back probe pins to slide into weather pack connectors on fuel injectors, TPS and MAP sensors. A hook probe with plunger actuation allows quick connection to pins or exposed conductors. Tested to 60V DC.

Manufacturer: Reed Brand: REED Instruments Model: ST-ELECTRICKIT

The Reed ST- ElectricKit Electrician's Combination Kit includes an AC clamp meter with temperature function, a voltage and continuity tester, a non-contact voltage detector with built-in flashlight, a temperature input adapter and Type K thermocouple wire probe, safety test leads, and a carrying case.The ST-335 clamp meter is an autoranging mini clamp meter with high resolution AC current measurement, temperature measurement to 1832°F/ 1000°C, 4,000-count backlit LCD screen, data hold and zero functions, diode test to 0.3mA and continuity buzzer, automatic shutoff, low battery indication, and a safety rating of European Union (EN) 61010-1 Category III up to 600V.The ST-9902N is a voltage and continuity tester with non-contact AC voltage detection, seven LEDs to indicate voltage, a beeper to indicate continuity, and a safety rating of Category III 600V. It has an AC voltage range of 12V, 24V, 48V, 110V, 230V, 400V, and 690V; a DC voltage range of 6V, 12V, 24V, 36V, 48V, 110V, and 220V; and a continuity range of 0 to 85kΩ. The tester runs on two AA batteries (included).The Reed AC-9 non-contact voltage detector is a pen-style detector for use on 50/60 Hz circuits, with a pocket clip, a built-in flashlight, and a voltage detection range of 90 to 600VAC. It runs on two AAA batteries (included), and a red flashing LED indicates the presence of live voltage. The detector has an EN safety rating of Category III 1000V.The TL 88-1 safety test leads can be used with the clamp meter. These two 48" flexible silicone insulated leads are heat- and cold-resistant and have stainless steel tips. One is black, and one is red.Specifications Clamp meter AC current range 40.00, 400.0 amp Clamp meter AC voltage range400.0mV, 4.000, 40.00, 400.0, 600VClamp meter DC voltage range 4.000, 40.00, 400.0, 600V Clamp meter resistance range400.0Ω, 4.000, 40.00, 400.0kΩ, 4.000, 40.00MΩClamp meter capacitance range40.00, 400.0nF, 4.000, 40.00,100μF Clamp meter frequency range5.000, 50.00, 500.0Hz, 5.000, 50.00, 150.0kHzClam...

Manufacturer: OUTEST Brand: OUTEST

Manufacturer: Kingzer Brand: KINGZER

Funuctions:Display Count: 6600Auto Range: √Jaw Capacity: 55mmTrue RMS: AC Voltage     Duty Cycle: 0.1%~99.9%     Diode: √Auto Power Off: √Continuity Buzzer: √Low Battery Indication: √Data Hold: √MAX/MIN: √LCD Backlight: √Full Icon Display: √Inrush Current: AC Current     Input Impedance for DCV: Around 10M¦¸     Specifications:Model: UT208AC Current (A): 66A/1000A ±(2%+8)DC Current (A): 66A/1000A ±(1.5%+8)AC Voltage (V): 6.6V/66V/600V ±(1.2%+5)DC Voltage (V): 6.6V/66V/600V ±(0.8%+1)Resistance (¦¸): 600¦¸/6.6K¦¸/66K¦¸/660K¦¸/6.6M¦¸/66M¦¸ ±(1%+2)Frequency (Hz): 660Hz/6.6KHz/66KHz/660KHz/6.6MHz/66MHz ±(1%+3)Temperature (°C): -40°C ¡« 1000°C ±(1%+3)Temperature (°F): -40°F¡«1832°F ±(1%+4)General Characteristic:Product Net Weight: 533gProduct Size: 286mm * 105mm * 45mmPower: 9V Alkaline Battery£¨6LF22)   (not included)LCD Size: 47mm * 30 mmProduct Color: Red and GreyPackage Weight: 1369g / 3lbPackage Size: 29.1 * 22.5 * 6.8cm / 11.4 * 8.9 * 2.7inPackage List:1 * UNI-T UT208 Digital Clamp Multimeter1 * Point Contact Temperature Probe1 * Tool Box1 * Test Lead1 * English Manual