Current Probes - Page 69

Manufacturer: Fluke Corporation Brand: Fluke Model: I3000S

Fluke current clamps are the ideal tools to extend the current ranges of Fluke tools. The i3000s is a clamp-on AC current clamp for use with oscilloscopes and multimeters with banana input using the supplied dual banana to BNC adapter. The clamp is optimized for measurement on power distribution systems. Nominal current range: 30A, 300A, 3000A. Continuous current range: 1A - 30A, 1A - 300A, 1A - 3000A. Maximum non-destructive current: 4000A. Lowest measurable current: 1A. Basic accuracy: 2 percent + 2 A (48-65 Hz) (percent reading + floorspec). Useable frequency: 10 Hz - 100 kHz. Output levels: 10 mv/A, 1 mv/A, 0.1 mv/A. Maximum voltage: 600V. Maximum conductor diameter: 64mm. Output cable length: 2.1m.

Manufacturer: IDI Brand: IDGroup

Contact Probes HEADLESS FLAT

Manufacturer: IDI Brand: IDGroup

Contact Probes HEADLESS 30 DEG SPEAR STEEL

Manufacturer: Mahr Federal Inc. Brand: Mahr Federal Model: EGH-1021

The Mahr EGH-1021 small bore probe is intended for use with the Mahr Pocket Surf series portable surface roughness gauge (sold separately) for inside-bore testing applications with a minimum inside diameter (ID) of 3.2mm (0.125") and a maximum depth of 19mm (0.75"). The probe's 90-degree conical diamond stylus has a 10μm (0.0004") radius, which is suitable for use when measuring rough surfaces. It measures average roughness (Ra), mean depth (Rz), and maximum depth (Rmax) parameters, and meets International Organization for Standardization (ISO) 4287 and American Society of Mechanical Engineers (ASME) B46.1 specifications. This small bore probe is suitable for applications such as evaluating a machined inner-bore surface.A surface roughness tester, also known as a profilometer, surtest, roughness gage, surface finish gage, or surf roughness tester, is a device used to inspect and measure surface roughness of flats, rounds, sloping planes, and recesses in machined, ground, or polished metal and non-metal surfaces. It is used for metrology in shop, metalworking, manufacturing, and quality control (QC) applications. Surface roughness testing is a type of form measurement that identifies surface profiles such as grooves and recessions, commonly known as peaks and valleys, of a surface. A roughness tester traces a surface profile using a skid-type (contact-type) method with a tracer tip such as a diamond stylus and piezo-electric detection to calculate roughness. Common types of parameters include Ra (roughness average), Rv (maximum profile valley depth), and Rsk (skewness), and assessed profiles. Profiles can have valuations such as cutoff, sampling, traversing, and evaluation-types of lengths. A surface roughness tester can have analog or digital display. A surface roughness tester can be portable, handheld, or desktop-type.Mahr Federal manufactures dimensional metrology instruments and metering systems. The company, founded in 1861, is headquartered in Goettingen, Germany.

Manufacturer: FLIR Systems, Inc. Brand: FLIR Model: TA60

The TA60 is a Thermocouple Probe with Adapter. Add to your test tools with FLIR Test Accessories that extend the functionality and versatility of your instruments. These accessories are certified to the latest standards and to the highest applicable rating level and come with a 2 year warranty.

Manufacturer: Fluke Corporation Brand: Fluke Model: L200

Small, rugged light easily attaches to any Fluke test probe. Bright white LED illuminates contact area. Frees both hands for work. 120 hours of battery life. Uses 2 3-volt watch batteries.

Manufacturer: Test Products International, Inc Brand: TPI Model: A256

AC/DC Amp current probe adapter. AC Amps: 0 to 400A and DC Amps: 0 to 400A. Accuracy: 0-400A = +/-1 percent of reading and 0-2000A = +/- 1.5 percent of reading. Adapter output: 1mV per 1A. Maximum conductor size: 34mm. 48" Lead length. Dual banana plug output connection type. Compatible unit: Most TPI brand and any competitor DMM, clamp-on or oscilloscope having the capability of measuring up to 2000mV AC/DC (2V AC/DC), 10megaohm input impedance, and equipped with industry standard spaced input jacks 19mm on center.

Manufacturer: AEMC Brand: AEMC Model: MR521

The AEMC MR series AC/DC probes are professional AC/DC current probes designed to extend current measuring capabilities of DMMs, oscilloscopes and other instruments. They are built to the latest safety and performance standards, including the ce mark and ul approval. Two different hook-shaped jaws are offered, both permitting the user to "pry" or "hook" onto cables (will accept 2 x 500MCM) or even onto small bus bars. The MR series probes use hall effect technology and measure AC and DC current. The electronics and batteries are self-contained in the handles. The output of the AC/DC probes is 1mV/A and 10mV/A. The model MR521 measures to 1000AAC/1500AAC. The model MR521 has two ranges and an auto-zero push button (patent pending) for quick DC zeroing. There is no output filtering - true RMS with DC component measurements are possible. Phase shift is excellent, making the MR series of current probes well suited for power and power quality applications. Measurement range of 400AAC/600ADC. Measurement range of 1000AAC/1500ADC. Double insulation. CE Mark. Applications: Dc motors, batteries, automobile engine testing, power measuring quality analysis, power load monitoring. 100AAC/150ADC and 1000AAC/1500ADC Nominal range. 0.2 to 1500A Measurement range. 150A-10mV/A, 1500A-1mV/A Output Signal. Overload: 2000AAC and 3000ADC continuous up to 1kHz. DC to 10kHz at -3dB Frequency range. 600Vrms Working/Common mode voltage. 9V Alkaline battery (approx. 50 hours life). 5' Lead output termination. Operating temperature: 14 degree to 131 degree F. Storage temperature: -40 degree to 176 degree F. 1.55" Jaw opening. Dimensions: 9-39/128" width by 3-11/16" height by 1-93/128" depth. Weight 1.06 lbs.

Manufacturer: Fluke Corporation Brand: Fluke Model: 2648355

Fluke IR smart battery charger for thermal imagers.

Manufacturer: Fluke Corporation Brand: Fluke Model: FOM

Plug the fluke FOM fiber optic power meter into your digital multimeter to make testing in tight spaces easier. The fluke fiber optic meter (FOM) helps you test and maintain fiber optic cable without having to buy a whole new meter. Plug the FOM directly into any DMM with a mV dc function and a 10 MO input impedance and quickly and accurately verify fiber optic cable system loss. Light sources and patch cords sold separately. A variety of light sources and patch cords let you get just what you need for testing different cable types and lengths. Highly accurate readings mean less work, less repeated testing. Input connector: fixed ST. 16 hours minimum battery life with 9V alkaline battery. LED low battery indicator. 0 to 40 degree C operating temperature. -20 to 70 degree C storage temperature.