Current Clamps - Page 12

Manufacturer: TED Brand: The Energy Detective Model: CT005A

The CT005A is a 200A split core current transformer. 200 Amp. Current Transformer. Solid Core.

Manufacturer: DENT Instruments Brand: DENT Instruments Model: CT-CON-0150EZ-U

DENT’s affordable and compact 150A EZ Clamp current transformers are the one-handed operating solution for temporary or long-term studies. They are designed to work in tight places and clamp around cables or buss bars. DENT’s energy monitoring components are used for a variety of applications, including building automation, tenant sub metering, performance verification, energy management and new technology assessment.

Manufacturer: Morris Products Brand: Morris Products Model: MP-57282

Output 100mV/A,1mV/A. Sensitivity 0.01A/mV AC/DC, ±3.0%, ±2%. Low Amp Current Adapter Weight: 7oz..

Manufacturer: Vetus Brand: ETCR

Technical Specifications Function: Measure AC/DC current, peak hold, online monitor Size of clamp: Φ68mm Range: DC:0.0A~2000A AC:0.0A~1500A Accuracy: ±2%rdg±3dgt Resolution: 0.1A Data interface: USB Power Supply: Zn-Mn dry battery 6F22 9V Test Mode: Clip-on CT, noncontact mode Display Mode: Four digits LCD display LCD Dimension: 35mm×21.5mm; display domain: 32mm×15mm Frequency: AC 45Hz~400Hz Sampling Rate: 2 times/s Polarity Indication: DC current auto identified and display"-" Test Position: Tested wire in the jaw center; Error will increase to 1.5%rdg max if deviate the center Range Shift: Automatically Line Voltage: below 600V Software: with the software the data can upload to computer Data Memory: 99units, FULL blinks when the memory is full Peak Hold: Push HOLD without release, the meter will show the peak value during the pushing period Reading Hold: DH indicating the reading is hold Out of Range: OL indicating the current is out of range Auto Power-off: 5 Minutes after power on, it will power off automatically to lower the power consumption Battery Voltage: Indicating the battery voltage is lower than 7.2V.Then the battery have to be changed Operating temperature and humidity: -10C~50C; Below 80%rh Max error refer to environment: -10C~0C,40C~50C,Error will increase max to 1%rdg Temperature and Humidity for storage: -10C~60C,below 70%rh Insulating Strength: AC2kV/rms. (between the alloy of the clamp and the housing) Applicable safety rules: IEC1010-1, IEC1010-2-032, Pollution level 2, CAT III (600V) Accessories: Meter: 1pc; USB communication line: 1pc; software: 1pc; bag: 1pc

Manufacturer: Fluke Corporation Brand: Fluke Model: 4637343

Fluke 24 inch iFlex flexible current probes expand the measurement range to 3000A AC while providing the ultimate measurement flexibility. The iFlex probes connect directly to the energy logger, displaying current measurements without error prone scaling factors. The 1.8 m (6 ft.) cord allows separation between the measurement location and the energy logger making it easier to view the display.

Manufacturer: Amprobe Brand: Amprobe Model: CT237B

The Amprobe CT237A current clamp probe measures AC or DC current without touching or interrupting the circuit. The Hall effect clamp has two jaws that fit around a 0.75" (19 mm) conductor. It converts a high-current signal to a low-level millivolt signal so it can be read by a testing device. The zero adjust knob allows operator to compensate for changes in output voltage due to environmental conditions. The clamp attaches to a compatible testing device, such as a digital multimeter, with a 59-inch, 1.5-meter lead. A finger guard on the body of the meter helps protect fingers from shock. The clamp operates on one 9V battery (included). It weighs 0.55 pounds (250 g) and measures 8.66 by 2.2 by 1.2 inches (220 x 55 x 30 mm, H x W x D, where H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; and D is depth, the horizontal distance from front to back). It meets applicable European Conformity (CE) directives.Clamp meters (also called clamp-on meters) measure electrical current without cutting through wires or touching or interrupting the electrical circuit. Available in handheld or benchtop models, clamp meters diagnose problems in electrical equipment, wiring, and power supplies. The meter's current clamp has two jaws that fit around a conductor to take measurements. All clamp meters test for current. Some come with test leads and inputs for measuring voltage, capacitance, and resistance. They display information either in analog or digital form. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltages determine meter choice. Safety ratings are based on the International Electrotechnical Commission's (IEC) standards for low-voltage test equipment. IEC 61010 delineates four overvoltage installation categories. In general, a meter with a category IV rating will provide more protection against transient voltages than a mete...

Manufacturer: Kyoritsu Brand: Kyoritsu Model: 8126

Kyoritsu 8126 load current clamp sensor. In order to monitor energy saving and to control the electric facilities, it is essential and imperative to control the leak and load currents from mains and branch power lines up to the equipment. Clamp sensor is easy to carry and simple to install. Load current detection type clamp sensors provide superior characteristic in phase for the use of power meter. Rated current 200Amp AC. 40mm conductor size. Output voltage: AC 500mV/200A (AC 2.5mV/A). Accuracy: +/- 0.5 percent rdg +/- 0.1mV (50/60Hz), +/- 1.0 percent rdg +/- 0.2mV (40Hz to 1kHz). Phase shift within +/- 1.0 degree. Output connector: Mini-DIN 6-pin. 0 to 50 degree c temperature range. Withstand voltage: 5350V AC for 5 seconds. Approximate 3m cable length. Approximate 5 ohm output impedance. Accessories includes: portable case, instruction manual, cable marker. Measures 128 mm length by 81 mm width by 36mm depth.

Manufacturer: Fluke Corporation Brand: Fluke Model: 3345766

Fluke 1 phase mini current clamp set for power quality logger. I5A/50A Current.

Manufacturer: Hioki Brand: Hioki Model: 9754

Clamp the clamp on noise sensor around the lan cable and monitor the noise Hilogger display. Measurement with the clamp on noise sensor is earth-free. The clamp on noise sensor measures noise current. The noise current level and frequency of the earth line can be measured simply, without direct contact. Because measurement requires no electrical contact, there's no need to worry about interfering with communications, electric shock or short circuits, and use is simple and safe even in active-line conditions. 1kHz to 100MHz (-3dB) band width. AC 10A (15A peak) rated current. +/-3.0 percent rdg, +/- 0.001 percent fs (fs = 10A, f=15kHz, with conductor centered in clamp) amplitude accuracy. up to f20mm measurable conductor diameter. CAT II 600V, CAT III 300V (insulated conductor) maximum rated voltage to earth. Measures 6-59/64" width by 2-23/32" height by 1-19/32" depth. 2m Cord length.

Manufacturer: Shinwa Brand: Shinwa Model: 62600

Trackable Shipping (Standard and Expedited)