Current Testers - Page 118

Manufacturer: FLIR Systems, Inc. Brand: FLIR Model: TA55

The TA55 is an AC Current Line Splitter. Add to your test tools with FLIR Test Accessories that extend the functionality and versatility of your instruments. These accessories are certified to the latest standards and to the highest applicable rating level and come with a 2 year warranty.

Manufacturer: waikei Brand: waikei

Features: The tester uses 3.7V rechargeable lithium battery (battery model: 14500) powered portable design, but you can use the T-MINIUSB outlet to charge the battery and power the system for a long time in the indoor use of more economical and convenient, eliminating the need always to be replaced battery of economic input! one key measurement operation, auto power off delay. Shutdown current is only 20nA, support for battery operation. Automatic detection PNP and NPN bipolar transistor, N, P-channel MOSFET, JFET FET, diodes, two diodes, thyristors, resistors, capacitors, inductors. Automatic detection pin definitions. Measuring the current amplification factor (B) of the bipolar transistor and the turn-on voltage of the emitter junction (Uf). Darlington transistor amplification factor can be identified by the high threshold voltage and high current. Can detect bipolar transistors and MOSFET's internal protection diodes and displayed on the screen. Measuring the threshold voltage and the gate capacitance of the MOSFET. Support two resistance measurements, the potential can be measured. If the potentiometer is adjusted to its end, the tester can not distinguish between the middle and the ends of the pin. Resistance measurement resolution is 0.1 ohms, the maximum value of 50M ohms measurements. Capacitance measurement range from 25pf to 100mF (100000 UF). Resolution up to 1 pF, inductance measurement range 0.01MH-20H, otherwise it will appear as a resistor, inductor DC resistance is higher than if Europe 2100 will also be displayed as a resistor. It can detect 2UF above capacitor equivalent series resistance (ESR), a resolution of 0.01 ohms. This feature is very important for the detection of the capacitor performance. Package Includes 1 x M328 version of the inductor-capacitor ESR table multifunction tester 3 x High quality test line (Batteries not included)

Manufacturer: PAI Industry Brand: PAI Industry

Spacer - .322 Inch Think BSP1061322

Manufacturer: PAI Industry Brand: PAI Industry

Spacer - .272 Inch Think BSP1061272

Manufacturer: Uni-T Brand: Uni-T Model: UT203

This is high quality clamp meter. Digital clamp meter UNI-T UT203 is a reliable and low consumption clamp multimeter. Digital clamp meter UNI-T UT203 measures AC/DC voltage and current, resistance, frequency, duty cycle, also performing diode check and continuity test. This clamp meter has overload protection. •Measuring functions: ◦AC/DC voltage ◦AC/DC current ◦Resistance ◦Temperature ◦Diode check ◦Continuity test ◦Duty cycle •Auto ranging •Data hold function •Display "REL" mode •Sleep mode •Low battery display •28 mm maximum jaw diameter •Measurement update speed 3 times/second •Compact and comfortable design •Compliance with safety requirements IEC 61010 CAT II 600 V, CAT III 300 V Specifications: DC voltage Range 400 mV / 4 V / 40 V / 400 V / 600 V AC voltage Range 4 V / 40 V / 400 V / 600 V DC current Range 40 A / 400 A AC current Range 40 A / 400 A Frequency Range 10 Hz / 100 Hz / 1 kHz / 10 kHz / 1 MHz Included: UT203 Meter Test Leads User's Manual

Manufacturer: UEi Test Instruments Brand: UEI Test Equipment Model: UTLDM1

ETL Listed IEC61010-1 CAT III 600V 1 Year Limited Warranty DC Voltage 2V ~ 600V AC Voltage 200V~600V DC Current 20mA~10A Resistance Diode Temperature -4DegreeF ~ 1832DegreeF Continuity < 60Ω Battery test 1.5V, 9V, 12V.

Manufacturer: PAI Industry Brand: PAI Industry

Assembly Housing Relief Valve EHG3150

Manufacturer: VDO Brand: VDO Model: 190 904

Cockpit Ammeter2-1/16"60 amps

Manufacturer: RioRand Brand: RioRand Model: MS2108A Color: MS2108A

Features:Perform measurements of AC/DC voltage and current, resistance, frequency, duty, capacitance, as well as continuity and diode test.Display: 4000 counts with analog bar LCD displayMaximum voltage between terminals and earth ground: DC 1000V or AC 750VOver range protection for all rangesReading hold functionSquare value measuring function (at AC A and AC V range)Maximum & minimum value measuring functionConverte rate: 3 times/secBar graph: 30 times/secAuto power offContinuity testDiode testMAX diameter for conductor:Ф26mmThis meter has been designed according to IEC-1010 concerning electronic measuring instruments with an overvoltage category CAT Ⅲ600V and pollution Specifications:Model:MS2108ADouble Insulation: Protection class CAT III 600V and pollution degree 2Display: 4000 countsDC Voltage Accuracy: 400mV±1%,4V/40V/400V±7%,1000V ±0.8%AC Voltage Accuracy: 4V/40V/400V±0.8%,750V ±1.0%DC Current Accuracy: 40A/400A ±2%AC Current Accuracy: 40A/400A ±2%Resistance Accuracy: 400Ω/4kΩ/40kΩ/400kΩ ±0.8%, 4MΩ/40MΩ ±1.2%Capacitance:0nF/400nF/4μF/40μF/400μF/4000μF±4%Frequency Accuracy:10Hz/100Hz/1KHz/10kHz/100kHz/1MHz/10MHz±1.5%, 10~10KHz±2%Duty cycle: 0.1% ~ 99% ±3%Operating Temperature:0℃ ~ 40℃ (32°F ~ 104°F)Storage Temperture:-10℃ ~ 50℃(10°F ~ 122°F)MAX. diameter for Jaw:Ф26mmDimension:208mm x 78mm x 35mmPower:1.5V (AAA) x 3Weight:340gBattery is not included

Manufacturer: Zhuhai Jida Huapu Instrument Co.,Ltd Brand: HoldPeak Model: HP-90EPC Color: blue black 90EPC

The HOLDPEAK 90EPC Auto / Manual Ranging Multimeter is designed for both commercial and residential applications. It is an auto/manual ranging meter for measuring AC/DC current and voltage, resistance, capacitance, frequency, temperature and duty cycles in commercial, home repair, automotive and electrical testing applications. It comes with non-contact voltage detection, a bright large backlit LCD display and auto power-off feature and also features Data Hold and Auto Back-Light, Relative Measurement, USB Port, Telephone Line Test(RJ11), Network Cable Test(RJ45). Specifications Safety/Compliances: IEC61010 CAT.III 1000V, CAT.IV 600V overvoltage and double insulation standard Display: Maximum reading 3999, analogue bar graph 41 segments Range selection: Auto or Manual Overload display: Display OL DC voltage: 400mV/4V/40V/400V (¡À0.5%), 1000V (¡À0.8%) AC voltage: 400mV (¡À1.2%), 4/40/400V (¡À0.8%), 750V (¡À1.2%) DC current: 400uA/4000uA/40mA/400mA (¡À1.2%), 4/20A (¡À2.0%) AC current: 400uA/4000uA/40mA/400mA (¡À1.5%), 4/20A (¡À2.5%) Capacitance: 51.2nF (¡À3.0%), 512nF/5.12uF/51.2uF (¡À2.5%), 100uF (¡À5.0%) Resistance: 400ohm/4k/40k/400k/4Mohm (¡À1.0%), 40Mohm (¡À1.5%) Frequency range: 5.12Hz ¨C 5.12MHz (¡À0.1%) hFE: Yes Diode test: Yes Continuity test: Yes Non-contact voltage detection: Yes Relative Value: Yes USB Port: Yes Dimensions: 6.6¡± x 3.48 x 2.36 Power: 9V 6F22 battery Weight: 0.71 lb Only woks with Windows XP & Win7. Package Includes 1 x HOLDPEAK 90EPC Digital Multimeter 1 x Test Leads 1 x Temperature Test Probe 1 x PC Link Software CD 1 x USB 1 x Carrying Case 1 x Operating Manual 1 x 9V 6F22 battery