Torque Gauges - Page 17

Manufacturer: Imada Brand: Imada

The Imada HTGS-40L Digital Torque Gauge with Programmable Setpoints, Capacity 40.00 ozf-in is a precision instrument that offers programmable high/low set-points for go/no-go testing. ORANGE lights up for measurements less than Low set-point, GREEN for between High and Low set-point, and RED for over High set-point. Store up to 1,000 values in memory, which can be displayed or transmitted using serial output. Use the real time mode to display torque transients, or the peak mode to capture the peak torque achieved during a test. Selectable measuring units of lbf-in, kgf-cm, or N-cm.

Manufacturer: AWS Brand: AWS

The AWS ILTT-150F Inline Digital Torque Tester for Quick Tool Verification, Range 15 - 150 Lb-ft, Drive Size 1/2 in is used to convert any non-impacting torque tool into a complete torque measuring & analyzing system, simply connect the tester to the square drive, attach a socket and measure clockwise or counter-clockwise torque. Suitable for use with any hand tool or non-impacting power tool including torque wrenches, breaker bars, nut-runners and more. Internal NiMH rechargeable batteries provide 8-10 hours continuous use.The ILTT takes just seconds to change test parameters, and works in either one button or automatic modes of operation. Reliability and ease of use are enhanced with features such as: Sign Lock, Peak Blanking and Auto Clear.

Manufacturer: Cedar Brand: Cedar

The Cedar DI-12-SL4N Yield Digital Torque Tester, Range 0.030 4.000 N-m is designed to find the actual yield tightening torque value for specific thread joints which consist of a variety of thread types, multi-layered material, hole sizes, etc. The yield value is the point at which the torque angle is no longer linear. Once the yield tightening torque value is found, one can easily determine the proper tightening torque value. DI-12 also captures the difficult-to-detect first peak dip in actual tightening torque of small screws. DI-12 provides a steady slow speed to capture the very small first peak dip and stops automatically to avoid over tightening. Torque data can be continuously output via RS-232 enabling you to display a torque profile showing, peak down, yield, and destructive strength torque using data acquisition software.

Manufacturer: Wilmar Corporation (Automotive) Brand: Performance Tool Model: M195

The Performance Tool M195 features a Pointed, hard spring steel beam that gives precise readings while resisting bending; Torque measurements calibrated in SAE & Metric; Deflection beam torque wrenches do not wear or fatigue over the lifetime of the tool insuring increased accuracy; 60in/lbs. Maximum Torque; 0-80 Working Torque; 0-7 Newton meters; Accurate measurements Clockwise or Counterclockwise; Corrosion Resistant; High-Contrast Dual Range Scale (Easy to read in low light); Can be used for rear differential, gunsmithing, and preload on pinion bearings where a click type torque wrench won't cut it. Also use it while tightening seat post clamp on carbon fiber bicycles or torqueing plastic intake manifolds. Use the M195 when need to measure break away torque.

Manufacturer: Tool connection Brand: Tool connection

Gauge ranges from 5 to 360 degrees with +/-1% accuracy.

Manufacturer: AWS Brand: AWS

The AWS RDFA-150 150 Lb-ft Rundown Fixture 1/2 inch Drive is required for accurate torque measurement for power-driven torque controlled tools (electric, hydraulic or pneumatic). The RDF Joint Simulator are not necessary or useful when measuring torque on manually-operated torque tools (screw-drivers, wrenches, etc.) It simulates the conditions found when using the tool in real-world conditions, allowing the speed of the power tool motor to ramp-up to normal operating speeds resulting in a more accurate and repeatable measurement of the torque. The Joint Simulator is typically fabricated from machined steel with the appropriate drive size as needed. Internally it is comprised of a series of Belleville washers, designed to compress as the bolt tightens. By varying the arrangement of these washers, various joint rates can be simulated soft, medium and hard.Unless otherwise, specified, Joint Simulators are configured to simulate a medium joint. The joint rates can be adjusted by the user by changing the orientation of the Belleville washers upside down.

Manufacturer: Checkline Brand: Checkline Model: TA-75

Torque tools which are in regular use need periodic checks to insure their accuracy. The TA-Series bench mounted torque analyzers are built for this purpose. These analyzers provide a means of quick and economical standardization. For use with hand operated tools only. Not for use with pneumatic or electric powered tools.

Manufacturer: Checkline Brand: Checkline Model: TAF-50

Torque tools which are in regular use need periodic checks to insure their accuracy. The TA-Series bench mounted torque analyzers are built for this purpose. These analyzers provide a means of quick and economical standardization. For use with hand operated tools only. Not for use with pneumatic or electric powered tools.

Manufacturer: Tohnichi Brand: Tohnichi Model: BTG15CNS

Tohnichi Analog Torque Gauge

Manufacturer: Cedar Brand: Cedar

The DID-4A Cedar Digital Torque Screwdriver with Memory & USB Data Output , 35 lb-in Capacity, 0.20~35.00 lbf-in Measuring Range is a torque measuring manual screw driver designed for lab and production use. The DID-4A is a new, improved version of the DID-4. The DID-4A increases the reliability of tool by removing the internal clutch from the unit. An optional ratchet, part number: RA2, is sold separately The large LCD display measures bi-directional torque in real-time or peak modes. USB data output allows the user to graph torque vs time with optional SW-1SV-USB software. The DID-4A Cedar Digital Torque Screwdriver with Memory & USB Data Output , 35 lb-in Capacity, 0.20~35.00 lbf-in Measuring Range is a Torque Screwdriver that has an accuracy of +/- 0.5% F.S., +/-1 LSD and has programmable set-points that provide both an audible beep and green/red LED indicator for uniform tightening or GO/NO GO testing. In addition, it features a programmable counter that minimizes assembly errors by identifying mis-tightening and/or defective screws. Use the 800 internal memory for data recall or USB download for SPC.The DID substantially reduces scrap and rework costs by eliminating over and undertightening and is ideal for use in a wide variety of applications including the manufacture of electronic, appliance and aerospace assemblies. All new units include a 3 point certificate of calibration traceable to NIST. ISO-17025 certificates are available and listed under a separate part number.