Dimensional Calibration - Page 37

Manufacturer: TTC Brand: TTC

Use for set-up and layout on drill presses and milling machines.

Manufacturer: Flexbar Brand: Flexbar

Inch Gage Indicator Ball with 4-48 stems for Flexbar Precision Indicator Gage Ball SystemTM (Size: .2812); Precision Grade Gage Balls with affixed threaded stems for use with dial gages and calipers. Easy to use and enables you to measure critical internal taper angles, taper openings, chamfers, groove locations and hole depths both quickly and accurately. Precision Indicator Gage Ball System eliminates complicated and costly setups with sine plates (gage block), optical comparators, flush pin gages, plug gages, chamfer, microm and similar checking devices for any related taper bore dimensions. System includes: a set of thirty-one balls chrome steel hardened to 63RC, ground and lapped, and certified to grade 25 Accuracy °.0001 inch diameter, sphericity .000025 inch, sizes ranging from .0938 to 1.2500 with affixed 4-48 threaded indicator stems.

Manufacturer: Flexbar Brand: Flexbar

Metric Indicator Ball with 4-48 stems for Flexbar Precision Indicator Gage Ball SystemTM (Size: 9mm). Precision Grade Gage Balls with affixed threaded stems for use with dial gages and calipers. The system enables you to measure critical internal taper angles, taper openings, chamfers, groove locations and hole depths quickly and accurately. With the Precision Indicator gage Balls you eliminate complicated and costly setups with sine plates (gage blocks), optical comparators, flush pin gages, plug gages, chamfer, micrometers and similar checking devices for any related taper bore dimensions.

Manufacturer: LittleMachineShop.com Brand: LittleMachineShop.com Model: LMS2881

These ultra precision 1-2-3 blocks are ground and case hardened on all sides to 55-60 Rc. They are parallel within 0.0001", flat within 0.0001" and square within 0.0001". They are up to 0.0003" oversize for lapping. Each set includes two matched blocks. T

Manufacturer: LittleMachineShop.com Brand: LittleMachineShop.com Model: LMS2881

These ultra precision 1-2-3 blocks are ground and case hardened on all sides to 55-60 Rc. They are parallel within 0.0001", flat within 0.0001" and square within 0.0001". They are up to 0.0003" oversize for lapping. Each set includes two matched blocks. T

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611201-541

The Mitutoyo grade AS-1 rectangular gage block is made of steel, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade AS-1 gage block is commonly used for workshop and inspection applications to calibrate fixtures and precision instruments, to inspect a variety of tools such as mounting tools, cutters, fixtures, and mechanical parts, and for gage manufacturing applications. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear-resistance. This gage block has a rectangular base for accurate wringing. Nominal length is measured in inches, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.355 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment and to standardize the measurement of length i...

Manufacturer: Echo Brand: ECHO Model: 70070358

Echo - push rod weldment, manufacturer part number 70070358

Manufacturer: HHIP Brand: HHIP Model: 4101-0911

.1009" Square Gage Block Grade AS-0 (2) Block is supplied with a manufacturer's certificate. 1/4" diameter hole. Tolerance is +.000004/-.000002".

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 611195-541

The Mitutoyo grade AS-1 rectangular gage block is made of steel, has its nominal length engraved in inches, and is supplied with a Mitutoyo inspection certificate that states that the block meets American Society of Mechanical Engineers (ASME) B89.1.9-2002 grade standard for flatness, length, parallelism, and surface finish. The inspection certificate specifies the deviation of the individual block from its nominal length. Gage blocks are commonly used to calibrate fixtures and precision instruments in workshop, inspection, and dimensional metrology applications, to inspect tools such as mounting tools, cutters, fixtures, and mechanical parts, and in the gage manufacturing process itself. This grade AS-1 gage block is commonly used for workshop and inspection applications to calibrate fixtures and precision instruments, to inspect a variety of tools such as mounting tools, cutters, fixtures, and mechanical parts, and for gage manufacturing applications. It is made of high-carbon, high-chrome steel which has a high hardness for minimum deterioration, and is selected for its wear-resistance. This gage block has a rectangular base for accurate wringing. Nominal length is measured in inches, and is indicated with laser-etched, black characters. The length of a gage block is usually slightly shorter than its stamped nominal length, to account for the thin layer of oil or wring film used when two or more blocks are wrung together. An identification number is laser-etched on the block for traceability. The block has a depth of 0.355 inches. It comes in a carrying case with a padded, formed interior. This gage block is supplied with a Mitutoyo inspection certificate [National Institute of Standards in Engineering (NIST)-traceable] that the block meets ASME B89.1.9-2002 standard for flatness, length, parallelism, and surface finish. Gage blocks (also called gauge blocks, Hoke blocks, Jo blocks, slip gages, and Johansson gages) are blocks used to calibrate measuring equipment and to standardize the measurement of length in...

Manufacturer: Flexbar Brand: Flexbar

Inch Gage Indicator Ball with 4-48 stems for Flexbar Precision Indicator Gage Ball SystemTM (Size: .9375); Precision Grade Gage Balls with affixed threaded stems for use with dial gages and Easy to use and enables you to measure critical internal taper angles, taper openings, chamfers, groove locations and hole depths both quickly and accurately. Precision Indicator Gage Ball System eliminates complicated and costly setups with sine plates (gage block), optical comparators, flush pin gages, plug gages, chamfer, micrometers and similar checking devices for any related taper bore dimensions. System includes: a set of thirty-one balls chrome steel hardened to 63RC, ground and lapped, and certified to grade 25 Accuracy °.0001 inch diameter, sphericity .000025 inch, sizes ranging from .0938 to 1.2500 with affixed 4-48 threaded indicator stems.