Reference Gauges - Page 54

Manufacturer: INSIZE Brand: INSIZE Model: 6535-30

Adjustable angle block, 4.0x1.2x1.9".

Brand: Techtongda magnetic chuck

Instructions： Put the workpiece on the suction table, and then insert the wrench into the shaft hole to turn clockwise180°, the workpiece can be sucked for processing. The workpiece is completed, the wrench can be inserted into the shaft hole to turn counterclockwise 180 °, you can remove the workpiece Maintenance： Sucker should be wiped clean before use to avoid scratching the surface, after using, the surface should be coated with oil to prevent corrosion. Use of ambient temperature: -40 ℃ -50 ℃. Do not knock, to prevent magnetic reduction. Strong dense pole permanent magnet sucker is for surface grinder, sparks machine, WEDM. Very fine spacing, uniform magnetic distribution, particularly for processing small thin parts. Worktable precision no change while magnetizing and demagnetizing. Panel with special treatment, no leakage, to prevent corrosion of cutting fluid. To prolong service life of the disk, it can be placed on the cutting fluid for storage.Six-surface fine grinding processing, the sucker can be used in  vertical direction on the wire cutting machine cutting. High-performance magnetic steel disk, with suction, almost no remanence. Suction can be 120N / cm2. Application: The magnetic chuckcan be used for processing various magnetic conduction work pieces. For surface grinder, tool grinder, EDM and other applications. Thin & light weight work piece are ideally suitable because of fine-pitched magnetic poles Item included(170420): 1× magnetic chuck

Manufacturer: Original Equipment Manufacture Brand: Plantronics Model: MSS191162H01 Color: Black

Backbeat Go 2 Black BackBeat GO 2 wireless earbuds deliver immersive audio for your non-stop life so you can lose the cord free your music and still take that call.

Manufacturer: Starrett Brand: Starrett Model: 667-20

This gauge is widely used in automotive, aviation, diesel and farm equipment manufacture and service and also in jig, fixture, gauge and experimental work.

Manufacturer: Reid Supply Company Brand: Precision Brand

Used for close spacing and extremely tight tolerance situations. Steel shims are made from close grain C1095 high carbon steel, hardened and tempered to Rc 48-62. Stainless steel shims are made from 1/2 wide, 300 series stainless steel, hardened and tempered to Rc 45-55. Flat lengths have rounded ends and are marked for size. Coiled lengths are etched every 6 and can be easily cut to length.

Manufacturer: HHIP Brand: HHIP Model: 4103-0096

Replace missing, damaged or worn-out Class ZZ gages from existing sets and libraries. ~ Each pin is individually marked with the size. ~ Fully hardened to 60-62 RC. ~ Finish to 10 Micron or better. ~ Overall length is 2". ~ Tolerance is - .0002".

Manufacturer: HHIP Brand: HHIP Model: 4103-0117

Replace missing, damaged or worn-out Class ZZ gages from existing sets and libraries. ~ Each pin is individually marked with the size. ~ Fully hardened to 60-62 RC. ~ Finish to 10 Micron or better. ~ Overall length is 2". ~ Tolerance is - .0002".

Manufacturer: HHIP Brand: HHIP Model: 4103-0100

Replace missing, damaged or worn-out Class ZZ gages from existing sets and libraries. ~ Each pin is individually marked with the size. ~ Fully hardened to 60-62 RC. ~ Finish to 10 Micron or better. ~ Overall length is 2". ~ Tolerance is - .0002".

Manufacturer: Vermont Gage Brand: Vermont Gage

The Vermont Gage steel no-go (-) plug gage is a class ZZ inch gage for calibrating measuring equipment and gage parts. A certificate of accuracy traceable to NIST is available for each gage, and each pin is marked with its size and direction of tolerance in sizes over .060”. Each gage is sealed in a volatile corrosion inhibitor (VCI) bag and packaged with a rust preventative. All gages measure 2” long, are within .00001” round (per ASME B89.1.5), and have at least a 10-microinch finish for a smooth finish. This gage is made of tool steel 60/62 Rc (cold stabilized) for durability and is available with either a steel or black guard finish (to inhibit corrosion and for indicating wear). Sizes are available from .0040” to 1.0005” (increments of .001”), with a tolerance of -.0002” for longer wear. Plug gages are precision ground cylindrical steel plugs used to measure the diameter and depth of drilled or machined holes. They are available in different classes, based on acceptable tolerance (allowed deviation from the stated size). Standard tolerances and classes for cylindrical gages up to .825” are as follows: Class XX (.00002" or .0005 mm), Class X (.00004" or .0010 mm), Class Y (.00007" or .0018 mm), Class Z (.0001" or .0025mm), and Class ZZ (.0002" or .0050 mm). For gages with a wider diameter, tolerance gradually increases for each class. Since 1968, Vermont Precision Tools, Inc. (VPT) has been manufacturing a variety of precision round and ground pins, perforators, and special punches. Vermont Gage was formed in 1980, and manufactures a wide range of fixed limit gages. Located in Swanton, Vermont and Franklin, Kentucky, Vermont Gage manufactures 98% of the products they sell and is ISO 9001:2000 and ISO 17025 quality certified.

Manufacturer: Vermont Gage Brand: Vermont Gage

The Vermont Gage steel no-go (-) plug gage is a class ZZ inch gage for calibrating measuring equipment and gage parts. A certificate of accuracy traceable to NIST is available for each gage, and each pin is marked with its size and direction of tolerance in sizes over .060”. Each gage is sealed in a volatile corrosion inhibitor (VCI) bag and packaged with a rust preventative. All gages measure 2” long, are within .00001” round (per ASME B89.1.5), and have at least a 10-microinch finish for a smooth finish. This gage is made of tool steel 60/62 Rc (cold stabilized) for durability and is available with either a steel or black guard finish (to inhibit corrosion and for indicating wear). Sizes are available from .0040” to 1.0005” (increments of .001”), with a tolerance of -.0002” for longer wear. Plug gages are precision ground cylindrical steel plugs used to measure the diameter and depth of drilled or machined holes. They are available in different classes, based on acceptable tolerance (allowed deviation from the stated size). Standard tolerances and classes for cylindrical gages up to .825” are as follows: Class XX (.00002" or .0005 mm), Class X (.00004" or .0010 mm), Class Y (.00007" or .0018 mm), Class Z (.0001" or .0025mm), and Class ZZ (.0002" or .0050 mm). For gages with a wider diameter, tolerance gradually increases for each class. Since 1968, Vermont Precision Tools, Inc. (VPT) has been manufacturing a variety of precision round and ground pins, perforators, and special punches. Vermont Gage was formed in 1980, and manufactures a wide range of fixed limit gages. Located in Swanton, Vermont and Franklin, Kentucky, Vermont Gage manufactures 98% of the products they sell and is ISO 9001:2000 and ISO 17025 quality certified.