Hole Gauges - Page 11

Manufacturer: Lamotte Brand: LaMotte

Soap Test Kit: In Grains Per Gallon (gpg): Ideal for verifying if water softener is functioning correctly.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 155-126

Mitutoyo Telescoping Gage, Range: 3-1/2" to 6"

Manufacturer: MITUTOYO Brand: Mitutoyo

.197-2.95" Small Hole Gage

Manufacturer: Flexbar Brand: Flexbar

Flexbar Precision Dial Calipers are now available in both inch and Metric Models. Features a thumbroll for rapid Setting and easy adjustment. Smooth, Precise feel and Accuracy. Stainless Steel - Hardened and Precision Ground Throughout. Special Features: Dial hand completes one revolution per each .100"; Large Dial means Wider-Spaced, easy-to-read Graduations. inverted covered rack helps prevent excess dirt accumulation in rack gear teeth to ensure Long Caliper life. Exclusive Dual Pinion Drive mechanism reduces wear on rack and Pinion. Adjustable Dial reads directly to .001"/0.02mm. Features Outside, inside and Depth Measurements. Beam is Graduated in .10" increments for easy Reference Points. Self-contained movement eliminates gear misalignment. Hardened stainless steel throughout With Measuring Faces Precision-ground and Micro-lapped for exceptional Accuracy. Knurled lock assures Precise Settings. Accuracy = .001"/0.02mm. Depth of Jaws: Model No. 16226 = 1 3/16", 16287 = 1.6"; Model No. 16279 = 2". Extra length of Jaws ensures Squareness & perfect Alignment. A raised bearing surface for sliding Jaw eliminates wear & defacement of Graduations on the beam. Price includes a fitted Case. inch Models Available in 4", 6", 8" and 12" Ranges. Metric Models Available in 150mm, 200mm and 300mm Ranges. Range: 0-8" Dial Grad.: .001"

Manufacturer: Starrett Brand: Starrett Model: 579B-8

Telescoping gauge is used for determining the true size of holes, slots, and recesses up to 6". The ends of both contact is hardened and ground to a radius to allow proper clearance on the smallest hole the gauge will enter. This tool must be slightly "rocked" in the hole being measured to ensure that the tool is on the proper diameter before it is locked and withdrawn. The final hole size is obtained by measuring over the gauge contact with a micrometer.

Manufacturer: Starrett Brand: Starrett

American Standard Wire Gage, Measuring Range 0-36 In, Graduations Numeral And Decimal, Tool Steel, Satin, Hardened and Accurate

Manufacturer: Fred V. Fowler Company, Inc. Brand: Fowler Model: 52-470-006-0

The Fowler 54-565-233 High-Accuracy Ultima Bore Gauging System has a measurement range of 7.878 to 8.27" and is accurate to + or - 0.00006". Resolution is 0.00001" and the measuring depth is 3.15". The gauge has constant spring pressure for repeatability and Bower's FastFit measuring heads for rapid measurement. It uses a three-point contact system for the detection of lobing or triangular form error, and ceramic contact points provide high durability and stability with regard to thermal expansion. The Ultima system requires connection to a Sylvac or multiplexer display unit.This product has 1 year warranty offered by Fowler High Precision. If you experience any problem contact Fowler directly for warranty claims.

Manufacturer: Fred V. Fowler Company, Inc. Brand: Fowler Model: 52-470-000-0

The Fowler 54-565-233 High-Accuracy Ultima Bore Gauging System has a measurement range of 7.878 to 8.27" and is accurate to + or - 0.00006". Resolution is 0.00001" and the measuring depth is 3.15". The gauge has constant spring pressure for repeatability and Bower's FastFit measuring heads for rapid measurement. It uses a three-point contact system for the detection of lobing or triangular form error, and ceramic contact points provide high durability and stability with regard to thermal expansion. The Ultima system requires connection to a Sylvac or multiplexer display unit.This product has 1 year warranty offered by Fowler High Precision. If you experience any problem contact Fowler directly for warranty claims.

Manufacturer: Flexbar Brand: Flexbar

Flexbar Sensing-Saf-Start. The inexpensive Solution to OSHA. Anti-automatic Restart Protection Without the High Cost of Magnetic Motor Starters This is a mandatory OSHA safety requirement. With the Sensing-Saf-Start correctly installed on existing equipment, it will Provide Protection against unexpected start-up, motion, and motor burn-out in the following manner: Voltage drop or power interruption Protection. in the event equipment, while being operated (switch in the "On" Position), should stop due to loss or drop of Electrical power due to Power Failure from any cause, the Sensing-Saf-Start will automatically Disconnect and shut off power to the equipment, so that upon restoration of power, the equipment will not start up even though the power switch to the equipment is in the "On" Position. in order to restore power to the equipment, the equipment switch must be turned "off" first, and then the Reset button on the Sensing-Saf-Start depressed. in the event the equipment is inadvertantly unplugged and then Plugged Back into the power source while the equipment switch is in the "On" Position, the equipment will not restart until the Reset button on the Sensing-Saf-Start is depressed. The Sensing-Saf-Start is intended for installation on equipment which operates on 120-volts or 240-volts A.C. and which is connected to the source of Electric power by means of a 3-Wire Flexible power Cord. The following Standards apply to Machines Driven by 120 volt and 240 volt motors: OSHA (US Occupational Safety and Health Administration 29 DFR #1910.213 (b) (3)*) NFPA (Electrical Standard for industrial Machinery, 1997 Edition, Section 8, Protection) Model No. 17023., 20" Cord on equipment switch End. 8' Cord on power End (No Plug). Wire directly into Disconnect box or instAll TwistLock Plug. Rated 120-volt, A.C., 18-amp 1 H.P. motor maximum, 50/60 cycle.

Manufacturer: Starrett Brand: Starrett Model: S579HZ

The Starrett S579HZ set of six telescoping gauges measures 5/16 to 6" holes, slots, and recesses in woodworking, metalworking, machining, layout, and pattern-making applications. The four gauges measure from 5/16 to 1/2", 1/2 to 3/4", 3/4 to 1-1/4", 1-1/4 to 2-1/8", 2-1/8 to 3-1/2", and 3-1/2 to 6". Each gauge has two spring-tensioned telescoping plungers for uniform contact pressure. The self-centering handles are rigidly attached to contact plungers. Five handles measure 2-3/8" and one handle measures 3-1/4" in length. A lock at the end of the handle secures the gauge width for measurement with a micrometer (sold separately). The gauge set comes in a protective case for storage. The L.S. Starrett Company manufactures precision measuring tools, metrology and testing equipment, and saw blade products. The company, founded in 1880, is headquartered in Athol, MA. What's in the Box?(6) piece telescoping gauge setProtective case