Hole Gauges - Page 13

Manufacturer: Starrett Brand: Starrett Model: 579A-12

Telescoping gauge is used for determining the true size of holes, slots, and recesses up to 6". The ends of both contact is hardened and ground to a radius to allow proper clearance on the smallest hole the gauge will enter. This tool must be slightly "rocked" in the hole being measured to ensure that the tool is on the proper diameter before it is locked and withdrawn. The final hole size is obtained by measuring over the gauge contact with a micrometer.

Manufacturer: Flexbar Brand: Flexbar

Flexbar Sensing-Saf-Start. The inexpensive Solution to OSHA. Anti-automatic Restart Protection Without the High Cost of Magnetic Motor Starters This is a mandatory OSHA safety requirement. With the Sensing-Saf-Start correctly installed on existing equipment, it will Provide Protection against unexpected start-up, motion, and motor burn-out in the following manner: Voltage drop or power interruption Protection. in the event equipment, while being operated (switch in the "On" Position), should stop due to loss or drop of Electrical power due to Power Failure from any cause, the Sensing-Saf-Start will automatically Disconnect and shut off power to the equipment, so that upon restoration of power, the equipment will Not start up even though the power switch to the equipment is in the "On" Position. in order to restore power to the equipment, the equipment switch must be turned "off" first, and then the ReSet button on the Sensing-Saf-Start depressed. in the event the equipment is inadvertantly unplugged and then Plugged Back into the power source while the equipment switch is in the "On" Position, the equipment will Not restart until the Reset button on the Sensing-Saf-Start is depressed. The Sensing-Saf-Start is intended for installation on equipment which operates on 120-volts or 240-volts A.C. and which is connected to the source of Electric power by means of a 3-Wire Flexible power Cord. The following Standards apply to Machines Driven by 120 volt and 240 volt motors: OSHA (US Occupational Safety and Health Administration 29 DFR #1910.213 (b) (3)*) NFPA (Electrical Standard for industrial Machinery, 1997 Edition, Section 8, Protection) Model No. 17024., 20" Cord on equipment switch End. 8' Cord on power End (No Plug). You must instAll matching Plugs. Rated 200 to 240-volt A.C., 15-amp (Single phase) 2 H.P. maximum, 50/60 cycle.

Manufacturer: TTC Brand: TTC

Plunger of gages expand from center, under spring tension, to size of hole being measured and is then locked in place by knurled knob. Measurement is made by a micrometer or a caliper.

Manufacturer: Aircraft Tool Supply Brand: Aircraft Tool Supply

Range: .125-.200". Ball hole gauges are used to determine the diameter of small holes. They are precision ground and heat treated for accuracy. Measures inside diameters of holes and grooves. Makes an ideal companion for our telescoping gauges.

Manufacturer: Starrett Brand: Starrett Model: 831A

This small hole gauge is well balanced tool that is ideal for accurately measuring small holes, slots, grooves, and recesses in all kinds of work. Accurate measurement is obtained by slightly "rocking" this gauge in the hole to be measured. This will guarantee contact at the true diameter. The final size is then obtained by measuring over the ball contacts with a micrometer.

Brand: Dritz

Dritz-OmniCraft Centering Ruler. A high precision multi-purpose centering ruler with enhanced double lines for use on light and dark surfaces. Has marking holes for aligning grommets, eyelets, stitching and more. Includes 30, 45 and 60 degree angle lines for diagonal cutting and marking. This package contains one 18x2-1/2 inch centering ruler with a zero in the middle for accurate and effortless centering of objects. Made in USA.This product meets the oversized requirement per UPS/FedEx. The shipping weight reflected is the dimensional weight. This product also meets the large package requirement per UPS/FedEx. The estimated shipping cost will include this fee.

Manufacturer: CENTRAL TOOLS INC Brand: Central Tools

Small Hole Gge .300-.400.

Manufacturer: Starrett Brand: Starrett Model: 579D-8

Telescoping gauge is used for determining the true size of holes, slots, and recesses up to 6". The ends of both contact is hardened and ground to a radius to allow proper clearance on the smallest hole the gauge will enter. This tool must be slightly "rocked" in the hole being measured to ensure that the tool is on the proper diameter before it is locked and withdrawn. The final hole size is obtained by measuring over the gauge contact with a micrometer.

Manufacturer: Starrett Brand: Starrett Model: 579D-12

Telescoping gauge is used for determining the true size of holes, slots, and recesses up to 6". The ends of both contact is hardened and ground to a radius to allow proper clearance on the smallest hole the gauge will enter. This tool must be slightly "rocked" in the hole being measured to ensure that the tool is on the proper diameter before it is locked and withdrawn. The final hole size is obtained by measuring over the gauge contact with a micrometer.

Manufacturer: Starrett Brand: Starrett Model: 579F-8

Telescoping gauge is used for determining the true size of holes, slots, and recesses up to 6". The ends of both contact is hardened and ground to a radius to allow proper clearance on the smallest hole the gauge will enter. This tool must be slightly "rocked" in the hole being measured to ensure that the tool is on the proper diameter before it is locked and withdrawn. The final hole size is obtained by measuring over the gauge contact with a micrometer.