Electronic Indicators - Page 18

Manufacturer: VCC Optoelectronics Brand: VCC Optoelectronics Model: L58D-G12-W

Leecraft Threaded Green LED indicator Lights, #10-32NF-2A Thread Size, 24 AWG Wire Size Features diffused (wide viewing angle) LED; built-in integral bezel. Termination: 6" color-coded wire leads, red = anode (+), black = cathode (–). Panel Range: 0.187" (4.76 mm) max. Mounting Hole: 0.191" to 0.196". Clear LEDs are also available. Other Options Available: 2 volt and 6 volt LED indicators.

Manufacturer: iGaging Brand: iGaging

iGaging ABSOLUTE Technology IndicatorThe iGaging digital electronic indicator with ABSOLUTE encoder always remembers and traces absolute origin zero or preset data. It provides unlimited measuring speed without losing its origin. This indicator will indicate absolute position when turned on. Features:SPC/USB Data PortABSOLUTE encoder technology - Unlimited measuring speed.IP54 ProtectionRead and convert Inch/mm displayOrigin setPreset valueShank diameter: 3/8"Carbide tip4-48 threaded tipFloating lug back2 Years warrantySpecifications:Range: 2"/100mmResolution: 0.0005"/0.01mmAccuracy: 0.0005"

Manufacturer: Tramex Brand: Tramex Model: HH14TP30

Heavy-duty Pin-type Wood Probe with Cable and Pins for use with CMEX2, MRH3 & PTM. Heavy Duty. Pin Type Wood Probe. Comes with cable and pins.

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 575-121

Mitutoyo IDU Digimatic Indicator, Resolution: 0.01mm Range: 25.4mm, Stem diameter: 8mm, Back: Flat back, Functions: On/Off, Data output, inch/mm conversion, Alarm: Low voltage, Counting value composition error, Over-flow error.

Manufacturer: Fowler Brand: Fowler

Articulating Magnetic Base features: Adjust in almost unlimited ways 85 lb. pull Fine adjust V-slot on base for mounting on rounded surfaces Indi-X blue FRACTION Electronic Indicator features: Direct Inch/Metric/Fraction conversion Auto off feature Lugback and 3/8 stem mountings Resolution: .0005 /.01mm/64ths Tolerance indicators Absolute/incremental reading Floating zero Carbide tipped point

Manufacturer: Mitutoyo Brand: Mitutoyo

Mitutoyo 543 series LCD Absolute Digimatic Indicator ID-S displays inch/metric measurements in a choice of resolution and 0.5"/12.7mm measuring range. The indicator is automatically set to zero when it is turned on for measuring in either or both directions (plus or minus), and has a 0.375"; diameter stem, a steel ball contact point with a 4-48 UNF (Unified National Fine) thread, and a choice of flat or lug back. The LCD display is automatically set to zero when powered on at the current spindle location for measuring in either or both directions, and has a sealed housing that is Ingress Protection (IP) certified IP42 for protection against dust and water. An audible alarm indicates low battery, scale contaminations, and data composition errors. The indicator has SPC (statistical process control) data output for data analysis (requires cable, not included). The indicator is powered by an SR44 battery (included).

Manufacturer: Mitutoyo Brand: Mitutoyo Model: 543-502

The Mitutoyo 543-502 Absolute Solar Digimatic Indicator is an inch and metric digital indicator with LCD for measuring surface variations that has measurement range of 0.5"/12.7mm and a resolution 0.00005"/0.001mm, a lug back, a 3/8" stem diameter, and a solar-powered battery that provides continuous operation at a lighting level of 40 lux and greater. The battery has a reserve capacity of approximately 3.5 hours when fully charged. The indicator's absolute sensor automatically restores the last origin position when the unit is powered on, aiding multipoint measurement. The lug back designs allows lug mounting from the rear of the indicator. The indicator is Ingress Protection certified IP42 against solid objects over 1mm and direct sprays of water up to 15 degrees from the vertical. It meets ANSI (American National Standards Institute) standards and AGD (American Gage Design) standards for stem diameter. It has an SPC (statistical process control) output by which data may be exported. Indicators are used manufacturing and scientific applications to monitor and measure tolerance. SpecificationsUnitsInch and metric, selectableDisplayLCDRange0.5"/12.7mmResolution0.00005"/0.001mmAccuracy0.0001"/0.003mmMeasuring force1.5 N or lessStem diameter3/8"MountingLug backPower sourceSolar-powered battery (installed)Dial indicators are also called dial gauges, probe, and electronic indicators. These precision instruments measure small linear distances and object sizes. The dial magnifies the measurement so that it can be easily read by the human eye. Frequently used in manufacturing, laboratories, and other industrial or mechanical fields, dial indicators are used anywhere a small measurement must be found and recorded or transferred, such as checking the variation in tolerance of a workpiece. Standard dial indicators measure the displacement along the axis of the indicator. Dial test indicators are very similar to dial indicators, except that the axis of measurement is perpendicular to the axis of the indicator. Dial and dial...

Manufacturer: CAS Corporation Brand: CAS Model: CI-2001AS

The CI-2001AS Indicator, with stainless steel enclosure. Use in a variety of applications - floor scales, livestock scales, platform scales, pallet scales, and much more. With it's bright red display, the CI-2001AS Indicator is easy to read. Legal for trade.

Manufacturer: Dwyer Instruments, Inc. Brand: Dwyer

The Series AN2 Indicating Alarm Annunciator provides visible and audible alarms for up to eight inputs. The annunciator also has two SPDT relay outputs that can be used to initiate external alarms, buzzers, or paging devices. The Integral 24 VDC power supply can power most level, temperature, pressure, and flow switches. Audible alarm conditions can be acknowledged, reset, or silenced either via the front panel push buttons or the rear terminal block. The Series AN2 can be set to any common ISA sequences including First-Out.

Manufacturer: INSIZE Brand: INSIZE Model: 2103-10E

Electronic indicator, 5 inch 12 7mm resolution 00005 inch 0/001mm.