Current Testers - Page 105

Manufacturer: VDO Brand: VDO Model: 190 104

Cockpit Ammeter 2-1/16" 60 amps

Manufacturer: Amprobe Brand: Amprobe Model: PM55A

The Amprobe PM55A digital multimeter with built-in non-contact voltage detector is an average-sensing, auto-ranging meter for measuring voltage, resistance, capacitance, frequency, and microcurrent in electrical testing applications. The attached test leads measure alternating current (AC) voltage and direct current (DC) voltage to 600 volts (V), resistance to 6 megaohms, capacitance to 2,000 microfarads, frequency to 30 kilohertz (kHz), and microcurrent to 2,000 microamp. The meter has a non-contact voltage detector that senses AC voltage without touching or interrupting the circuit. The meter measures 4.4 x 2.1 x 0.4 inches (H x W x D, where H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; and D is depth, the horizontal distance from front to back), and it can be carried in a shirt pocket when not in use. The microamp reading identifies current changes in flame detector applications. The meter automatically selects AC voltage, DC voltage, or resistance function based on input. An audible continuity sensor confirms that the circuit conducts electricity, and a diode test detects whether the circuit's diodes work properly. An auto power-off mode turns off the unit after 10 minutes of non-use to conserve battery life, and a low-battery indicator signals when the meter's batteries need to be replaced.This average sensing, or average responding, meter provides accurate readings when measuring linear loads, such as standard induction motors and incandescent lights, where the current or voltage has a sinusoidal waveform. It is an auto-ranging meter and automatically selects the correct operating range for the property being measured. The meter has a 6,000-count (3-5/6 digit) liquid crystal display (LCD) that can display up to 5,999 units before the operating range needs to be changed. It meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category II installations up to 600V (which covers large house...

Manufacturer: Amprobe Brand: Amprobe Model: DM73C

The Amprobe DM73C digital multimeter is an average-sensing, auto-ranging multimeter with built-in test probe for measuring voltage and resistance in electrical testing applications. The meter measures alternating current (AC) voltage and direct current (DC) voltage to 600 volts (V) and resistance to 34 megaohms. The meter measures 7.8 x 1.1 x 1.4 inches (H x W x D, where H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left to right; and D is depth, the horizontal distance from front to back), and it can be carried in a pocket when not in use. It has a liquid crystal display (LCD) that shows readings both in digits and on a 34-segment bar graph. An audible continuity sensor confirms that the circuit conducts electricity, and a diode test detects whether the circuit's diodes work properly. The hold function keeps a reading on the display, even after the meter is disconnected. An auto power-off mode turns off the unit after 10 minutes of non-use to conserve battery life, and a low-battery indicator signals when the meter's batteries need to be replaced. Amprobe began life in Long Island, NY in the late 1940's under the name Pyramid Instrument Company. In 1960 the company name was formally changed to Amprobe Instrument Corporation. Amprobe continued to design, engineer, manufacture and distribute product from its Lynbrook, NY location until it was merged to form ATP and relocated to South Florida in late 1999.

Manufacturer: Klein Tools Brand: Klein Tools Model: CL100

The Klein CL100 600A AC Clamp Meter is a multi-featured clamp meter. It measures AC/DC voltage, AC current, and resistance. It can also test diodes and continuity. It has a backlit display and worklight, and includes case, test leads, and batteries. Weight: 0.62 lbs. Since 1857, the company operated by Mathias Klein and his descendants to the fifth generation, has grown and developed along with the telecommunications and electrical industries where Klein pliers first found major usages. Today, Klein Tools Inc represents much more than Klein pliers. The company's product line has broadened to include virtually every major type of hand tool used in construction, electronics, mining and general industry in addition to the electrical and telecommunications fields. Internationally, Klein's products are available around the world through a well-established network of agents and distributors who stock the products that are required for their particular markets. Klein's reputation as a leading producer of professional-quality products is global.

Manufacturer: Extech Brand: Extech Model: MA250

EXTECH 200 A AC Clamp Meter

Manufacturer: Zhuhai Jida Huapu Instrument Co.,Ltd Brand: HoldPeak Model: HP-90BS Color: blue black 90BS

The HOLDPEAK 90BS Auto / Manual Ranging Multimeter is designed for both commercial and residential applications. It is an auto/manual ranging meter for measuring AC/DC current and voltage, resistance, capacitance, frequency, temperature and duty cycles in commercial, home repair, automotive and electrical testing applications. It comes with non-contact voltage detection, a bright large backlit LCD display and auto power-off feature and also features Data Hold and Max/Min Reading, C/F exchange, Solar Charge, USB Port. Specifications Safety/Compliances: IEC61010 CAT.III 1000V, CAT.IV 600V overvoltage and double insulation standard Display: Maximum reading 6000, analogue bar graph 41 segments Range selection: Auto or Manual Overload display: Display OL DC voltage: 600mV (¡À1.2%), 6/60/600V (¡À0.8%), 1000V (¡À1.5%) AC voltage: 600mV (¡À2.5%), 6/60/600V/750V (¡À1.0%) DC current: 600uA/6000uA/60mA/600mA (¡À1.0%), 6/10A (¡À1.5%) AC current: 600uA/6000uA/60mA/600mA (¡À1.5%), 6/10A (¡À2.0%) Capacitance: 9.999nF (¡À3.0%), 99.99nF/999.9nF/9.999uF (¡À2.5%), 99.99uF/999.9uF (¡À3.0%), 9.999mF/99.99mF (¡À3.5%) Resistance: 600ohm/6k/60k/600kohm (¡À1.2%), 6Mohm (¡À1.5%), 60Mohm (¡À2.5%) Frequency range: 9.999Hz ¨C 9.999MHz (¡À0.5%) hFE: Yes Diode test: Yes Continuity test: Yes Non-contact voltage detection: Yes C/F Temperature Unit Select: Yes True RMS: Yes Relative Value: Yes MAX/MIN Value Test: Yes Solar Charge: Yes USB Port: Yes Dimensions: 6.6¡± x 3.48 x 2.36 Power: 9V 6F22 battery Weight: 0.71 lb Package Includes 1 x HOLDPEAK 90BS Digital Multimeter 1 x Test Leads 1 x special recharge wire 1 x Charger 1 x Carrying Case 1 x Operating Manual 1 x 9V 6F22 battery

Manufacturer: Zhuhai Jida Huapu Instrument Co.,Ltd Brand: HoldPeak Model: HP-90BS Color: blue black 90BS

The HOLDPEAK 90BS Auto / Manual Ranging Multimeter is designed for both commercial and residential applications. It is an auto/manual ranging meter for measuring AC/DC current and voltage, resistance, capacitance, frequency, temperature and duty cycles in commercial, home repair, automotive and electrical testing applications. It comes with non-contact voltage detection, a bright large backlit LCD display and auto power-off feature and also features Data Hold and Max/Min Reading, C/F exchange, Solar Charge, USB Port. Specifications Safety/Compliances: IEC61010 CAT.III 1000V, CAT.IV 600V overvoltage and double insulation standard Display: Maximum reading 6000, analogue bar graph 41 segments Range selection: Auto or Manual Overload display: Display OL DC voltage: 600mV (¡À1.2%), 6/60/600V (¡À0.8%), 1000V (¡À1.5%) AC voltage: 600mV (¡À2.5%), 6/60/600V/750V (¡À1.0%) DC current: 600uA/6000uA/60mA/600mA (¡À1.0%), 6/10A (¡À1.5%) AC current: 600uA/6000uA/60mA/600mA (¡À1.5%), 6/10A (¡À2.0%) Capacitance: 9.999nF (¡À3.0%), 99.99nF/999.9nF/9.999uF (¡À2.5%), 99.99uF/999.9uF (¡À3.0%), 9.999mF/99.99mF (¡À3.5%) Resistance: 600ohm/6k/60k/600kohm (¡À1.2%), 6Mohm (¡À1.5%), 60Mohm (¡À2.5%) Frequency range: 9.999Hz ¨C 9.999MHz (¡À0.5%) hFE: Yes Diode test: Yes Continuity test: Yes Non-contact voltage detection: Yes C/F Temperature Unit Select: Yes True RMS: Yes Relative Value: Yes MAX/MIN Value Test: Yes Solar Charge: Yes USB Port: Yes Dimensions: 6.6¡± x 3.48 x 2.36 Power: 9V 6F22 battery Weight: 0.71 lb Package Includes 1 x HOLDPEAK 90BS Digital Multimeter 1 x Test Leads 1 x special recharge wire 1 x Charger 1 x Carrying Case 1 x Operating Manual 1 x 9V 6F22 battery

Manufacturer: Simpson Electric Company Brand: Simpson

Instrument Protection and Storage CASE FRONT LOAD 260

Manufacturer: Megger Brand: Megger Model: 246034

The Megger 246034 CT miniature current sensor is a clamp-on current sensor with a 2.5' lead that connects to BITE 2 and BITE 2P receivers to measure test current. The sensor measures 4.44 x 1.34 inches (H x W, where H is height, the vertical distance from the lowest to highest point; and W is width, the horizontal distance from left to right), and it can be used for taking measurements on small-gauge wires and in areas where space is limited. The current clamp has a 1.5" jaw opening to measure current without disconnecting the circuit. It can be used to test noisy battery systems and does not require parallel battery strings to be isolated before testing for ground faults. The sensor has a maximum current input of 150 amp. It weighs 5.6 oz. (159 g). Battery testers are used in the industrial, commercial, medical, telecommunications, aircraft, power utility, and military industries to detect the health of a battery. They can measure conductance, impedance, voltage, and current, among other parameters. Battery testers are designed for specific types of batteries, such as lead-acid, nickel-metal-hydride (NiMH) and alkaline batteries. Some testers require a load to be applied to the battery during testing, and some do not. A variety of test leads with contacts, probes, clamps, clips, and other connectors can be used to connect a battery to a tester. Since different testers can measure different parameters to calculate battery health, it is important to use the same tester for consecutive tests on a single battery when analyzing changes in battery health over time. Megger manufactures equipment for cable fault locating, protective relay testing, telecommunications and data integrity, and power quality testing under multiple brand names, among them Megger, Biddle, States, and AVO. The company, founded in 1889, is headquartered in Dover, England, and meets International Organization for Standardization (ISO) 9001:2008 standards.

Manufacturer: Blue Sea Systems Brand: Blue Sea Systems

DC Analog Ammeter,Shunt Type: External,Simple 2-wire connection, Meter Senses Powers from same connection, Includes DC Shunt, Backlit meter face.